Inspire LEG PRESS 2 OPTION Supplement

ASSEMBLY & OPERATION MANUAL
LEG PRESS 2 OPTION
RECORD SERIAL NUMBER HERE
www.inspirefitness.net by Health In Motion LLC 10-30-07

TABLE OF CONTENTS
Section Description………………………………………………….. Page
Instructions………………………………………………………………….. 1
Tools Required……………………………………………………………… 1
Parts & Hardware List………………………………………………….. 2
Hardware Sizing Chart ………………………………………………… 3
Cable Chart …………………………………………………………………. 4
Assembly Instructions – attaching to M1 & M2 …………. 6
Assembly Instructions – attaching to M3……….………….. 9
Assembly Instructions – attaching to M4……….………….. 12
Decal Reference……………………………………………………………. 21
Decal Placement…………………………………………………………… 22
General Maintenance Information…….………………………… 23
Maintenance Schedule…….………………………………………….. 24
Limited Warranty.………………………….……………………………. 25

BEFORE ASSEMBLING YOUR LEG PRESS
IMPORTANT: Read this entire manual before attempting to build or use
your leg press. This manual contains step by step instructions for proper
assembly.
Use the parts list included in this manual to verify that all parts are
accounted for before assembly. If any parts are missing, contact the retailer
of this home gym for replacement parts. Or, call Inspire at 714-738-1729
Service of your home gym should only be preformed by an authorized
INSPIRE retailer. Service preformed by anyone else can result in loss of
warranty. Use only Inspire replacement parts on this machine. The use of
any other brand of parts can also result in a loss of warranty. If you need
help finding an authorized retailer, please contact us directly:
Inspire Fitness
637 S State College Blvd.
Fullerton, CA 92831
Ph: 714-738-1729
Fx: 714-738-1728
www.inspirefitness.net
TOOLS REQUIRED FOR ASSEMBLY
• Standard socket set (including 9/16” and 3/4” sockets)
• 9/16” wrench
• 3/4” wrench
• Adjustable wrench
• Tape Measure
• Rubber Mallet
PAGE 1

PARTS & HARDWARE LIST
Item Parts Description Qty
Qty
Rec'd Item Hardware Description Qty
Qty
Rec'd
1 Leg Press Base 1 1 Bolt, 3/8-16 x 1" L Button Head 4
2 Press Arm, Left 1 2 Bolt, 3/8-16 x 1" L 2
3 Press Arm, Right 1 3 Bolt, 3/8-16 x 1 1/4" L 2
4 Foot Plate 2 4 Bolt, 3/8-16 x 1 3/4" L 2
5 Leg Press Attachment Arm 1 5 Bolt, 3/8-16 x 2" L 10
6 Back Pad Stem 1 6 Bolt, 3/8-16 x 2 1/2" L 4
7 Dual Pulley Mount 1 7 Bolt, 3/8-16 x 3 3/4" L 1
8 Seat Base 2 8 Bolt, 3/8-16 x 4 1/4" L 2
9 Handle Assy 1 9 Bolt, 3/8-16 x 4 3/4" L 1
10 Floating Dual Pulley Bracket 1 10 Bolt, 3/8-16 x 5" L 5
11 LP2-M4 Attachment Cable 1 11 Bolt, 3/8-16 x 8" L 1
12 Locking Rod 1 12 Bolt, 1/2-13 x 10 3/4" L 1
13 3 1/2" Pulley 9
14 LP2 Main Cable 1 13 3/8" Washer 41
14 3/8" Small OD Washer 6
15 1/2" Washer 2
16 3/8-16 Locknut 18
17 3/8-16 Thin Locknut 4
18 1/2-13 Locknut 1
19 Barrel Spacer, 5/16” Long 1
20 Barrel Spacer, 3/8” Long 4
21 Cable End with Bushing 2
22 Cable Adapter 1
23 Adjustable Bumper 2
24 6mm Allen Wrench 1
Note: There may be extra hardware left over depending on which machine
the LP2 is attached.
PAGE 2

3/8" DIA. Bolt Allen Wrench
1/2" Washer 3/8" Washer 3/8" Small OD Washer Cable End
1/2" Locknut 3/8" Locknut 3/8" Thin Locknut 3/8" Barrel Spacer Bushing Sleeve
1/2" DIA. Bolt
ACTUAL PARTS MAY BE SMALLER OR LARGER THAN SHOWN
1" 2" 3" 4" 5" 6" 7"
HARDWARE SIZING CHART
PAGE 3

LP2-M4 Attachment Cable
LP2 Main Cable
CABLE CHART
Page 4

Assembly Instructions Leg Press 2
Assembly Procedures for attaching LP2 to Home Gym
Refer to page 6 if attaching to M1 & M2
Refer to page 9 if attaching to M3
Refer to page 12 if attaching to M4
Page 5

Assembly Procedure for attaching Leg Press 2 to M1 & M2
NOTE: The Leg Press may be attached to either side of the Home Gym.
The Illustrations show only one side.
DisconnectCable&
RemovePulley1
Step 1: Remove Pulley 1 and disconnect Lower Cable from Home Gym. Retain
Pulley 1 and hardware for later use.
Page 6
STEP
1
Lower Cable

2– 5” Hex Bolts 1– 4 ¾” Hex Bolt
4– 3/8” Flat Washers 1 – 3/8” Flat Washer
2 – 3/8” Lock Nuts
Leg Press Base Attachment Arm
2 – 5” Hex Bolts
Home Gym 4 – 3/8” Flat Washers
2 – 3/8” Lock Nuts
Step 2: Attach Attachment Arm to Home Gym using: Two (3/8” x 5” Hex Bolts)
(Finger Tighten Only) Four (3/8” Flat Washers)
Two(3/8”LockNuts)
Step 3: Attach Leg Press Base to Attachment Arm using: Two (3/8” x 5” Hex Bolts)
(Wrench Tighten Bolts in Steps 2 & 3 Now) One (4 ¾” Hex Bolt)
Five(3/8”FlatWashers)
Two(3/8”LockNuts)
Page 7
S
TEP 2
STEP 3

1– 3 ½” Pulley 1– 3 ½” Pulley
1– 2” Hex Bolt 1– 2” Hex Bolt
2– 3/8” Flat Washers 2– 3/8” Flat Washers
1– 3/8” Lock Nut 1– 3/8” Lock Nut
1 – 2” Hex Bolt
2– 3/8” Flat Washers
1 – 3/8” Lock Nut
1–2”HexBolt
2– 3/8” Flat Washers
1–3/8”LockNut
Step 4: Attach Pulley 8 to Attachment Arm using:
One (3 ½” Pulley) One (3/8” x 2” Hex Bolt)
Two (3/8” Flat Washers) One (3/8” Lock Nut)
Step 5: Attach Pulley 9 to Floating Dual Pulley Bracket using:
One (3 ½” Pulley) One (3/8” x 2” Hex Bolt)
Two (3/8” Flat Washers) One (3/8” Lock Nut)
Step 6: Thread Home Gym Lower Cable around Pulleys 8 & 9 and attach cable eyelet end to
Attachment Arm (bottom hole) using:
One (3/8” x 2” Hex Bolt) Two (3/8” Flat Washers)
One (3/8” Lock Nut)
Step 7: Attach Retainer Bolt to Attachment Arm using:
One (3/8” x 2” Hex Bolt) Two (3/8” Flat Washers)
One (3/8” Lock Nut)
(Wrench Tighten Bolts in Steps 4-7 Now)
(Make sure that the cable is routed between pulley 8 and the cable retainer bolt.)
Assembly Steps are continued on page 15
Page 8
STEP 5 STEP 4
Pulley-9
Pulley-8
STEP 7
STEP 6 Cable
Retainer
Bolt
Floating Dual
Pulley Bracket

Assembly Procedure for Attaching Leg Press 2 to M3
NOTE: The Leg Press may be attached to either side of the Home Gym.
The Illustrations show only one side.
Disconnect Middle Cable
RemovePulley1&1”BarrelSpacer
fromM3BaseFrame
Remove the Swivel Pulley Bracket
fromM3BaseFrame
Step 1: Remove the Swivel Pulley Bracket from the M3 Main Upright. Leave the cable
connected to the Swivel Pulley. Save Washers and Locknuts for later use.
Step 2: Remove Pulley 1 and 1” long Barrel Spacer from M3 Main Upright.
Save parts for later use.
Step 3: Disconnect the Middle Cable from the Main Upright. Re-install Bolt, Washers and
Locknut. Wrench tighten bolt.
Page 9
STEP 3
S
TEP 2
STEP
1
Middle Cable
Pulley 1 &
Barrel Spacer
Main Upright
Swivel Pulley

2– 5” Hex Bolts 1 – 4 ¾” Hex Bolt 1 – 3 ¾” Hex Bolt
4– 3/8” Flat Washers 1 – 3/8” Flat Washer 1– 5/16” Barrel Spacer
2 – 3/8” Lock Nuts 2 – 3/8” Flat Washers
1 – 3/8” Lock Nut
1 – 3 ½” Pulley
1– 1” Barrel Spacer
Leg Press Base Attachment Arm
2 – 4 ¼” Hex Bolts
Home Gym 4 – 3/8” Flat Washers
2 – 3/8” Lock Nuts
Step 4: Attach Attachment Arm and Swivel Pulley Bracket to Home Gym using:
Two (3/8” x 4 ¼” Hex Bolts)
(Finger Tighten Only) Four (3/8” Flat Washers)
Two(3/8”LockNuts)
Step 5: Attach Attachment Arm to Main Upright using: One (3/8” x 3 ¾” Hex Bolt)
Note: Re-install Pulley 1 & 1” Barrel Spacer One (5/16” Barrel Spacer)
in original location Two(3/8”FlatWashers)
(Finger Tighten Only) One(3/8”LockNut)
One (3 ½” Pulley)
One (1” Barrel Spacer)
Step 6: Attach Leg Press Base to Attachment Arm using: Two (3/8” x 5” Hex Bolts)
One(4¾”HexBolt)
Five(3/8”FlatWashers)
(Wrench Tighten all Bolts in Steps 4 - 6 Now) Two (3/8” Lock Nuts)
Page 10
S
TEP
4
STEP 6
S
TEP
5
5/16” Barrel Spacer

1– 3 ½” Pulley 1 – 3 ½” Pulley
1– 2” Hex Bolt 1 – 2” Hex Bolt
2– 3/8” Flat Washers 2 – 3/8” Flat Washers
1– 3/8” Lock Nut 1 – 3/8” Lock Nut
1 – 2” Hex Bolt
2– 3/8” Flat Washers
1 – 3/8” Lock Nut
2” Hex Bolt
2– 3/8” Flat Washers
1 – 3/8” Lock Nut
Step 7: Attach Pulley 8 to Attachment Arm using:
One (3 ½” Pulley) One (3/8” x 2” Hex Bolt)
Two (3/8” Flat Washers) One (3/8” Lock Nut)
Step 8: Attach Pulley 9 to Floating Dual Pulley Bracket using:
One (3 ½” Pulley) One (3/8” x 2” Hex Bolt)
Two (3/8” Flat Washers) One (3/8” Lock Nut)
Step 9: Route Home Gym Middle Cable around Pulleys 8 & 9 and attach eyelet end to
Attachment Arm (bottom Hole) using:
One (3/8” x 2” Hex Bolt) Two (3/8” Flat Washers)
One (3/8” Lock Nut)
Step 10: Attach Retainer Bolt to Attachment Arm using:
One (3/8” x 2” Hex Bolt) Two (3/8” Flat Washers)
One (3/8” Lock Nut)
(Wrench Tighten Bolts in Steps 7-10 Now)
(Make sure that the cable is routed between pulley 8 and the cable retainer bolt.)
Assembly Steps are continued on page 15
Page 11
STEP 8 STEP 7
Pulley-9
Pulley-8
STEP 9
STEP 10
Floating Dual
Pulley Bracket
Cable
Retainer
Bolt

Assembly Procedure for Attaching Leg Press 2 to M4
NOTE: The Leg Press can only be attached to the right side
of the Home Gym.
Step 1: Disconnect Floating Pulley Bracket from Main Upright and save removed hardware.
Page 12
Floating Pulley
Bracket
STEP 1

2– 5” Hex Bolts 1– 4 ¾” Hex Bolt
4– 3/8” Flat Washers 1 – 3/8” Flat Washer
2 – 3/8” Lock Nuts
2 – 1 ¼” Hex Bolts
4 – 3/8” Flat Washers
2 – 3/8” Lock Nuts
Step 2: Attach Leg Press Attachment Arm to Home Gym using:
Two (3/8” x 1 ¼” Hex Bolts)
Four (3/8” Flat Washers)
(Finger Tighten Only) Two (3/8” Lock Nuts)
Step 3: Attach Leg Press Base to Leg Press Attachment Arm using:
Two (3/8” x 5” Hex Bolts)
One(4¾”HexBolt)
Five(3/8”FlatWashers)
(Wrench Tighten Bolts in Steps 2 & 3 Now) Two (3/8” Lock Nuts)
Page 13
Le
g
Press Base
Leg Press
Attachment Arm
Home G
y
m
S
TEP 2
STEP 3
Use Upper Holes

1– 3 ½” Pulley 1– 3 ½” Pulley
1– 2” Hex Bolt 1– 2” Hex Bolt
2– 3/8” Flat Washers 2– 3/8” Flat Washers
1– 3/8” Lock Nut 1– 3/8” Lock Nut
1– Cable Adapter
1– 2” Hex Bolt
2– 3/8” Flat Washers
1– 3/8” Lock Nut
1– 3 ½” Pulley
1–2”HexBolt 1– 2” Hex Bolt
2– 3/8” Flat Washers 2– 3/8” Flat Washers
1– 3/8” Lock Nut 1– 3/8” Lock Nut
Step 4: Attach LP2-M4 Attachment Cable end to Floating Pulley Bracket using:
One (3 ½” Pulley) One (Cable Adapter)
One (3/8” x 2” Hex Bolt) Two (3/8” Flat Washers) One (3/8” Lock Nut)
Step 5: Attach Pulley 8 to Attachment Arm using:
One (3 ½” Pulley) One (3/8” x 2” Hex Bolt)
Two (3/8” Flat Washers) One (3/8” Lock Nut)
Step 6: Attach Pulley 9 to Floating Dual Pulley Bracket using:
One (3 ½” Pulley) One (3/8” x 2” Hex Bolt)
Two (3/8” Flat Washers) One (3/8” Lock Nut)
Step 7: Route LP2-M4 Attachment Cable around Pulleys 8 & 9 and attach cable eyelet end to
Attachment Arm (bottom hole) using:
One (3/8” x 2” Hex Bolt) Two (3/8” Flat Washers) One (3/8” Lock Nut)
Step 8: Attach Cable Retainer Bolt to Attachment Arm using:
One (3/8” x 2” Hex Bolt) Two (3/8” Flat Washers) One (3/8” Lock Nut)
(Wrench Tighten Bolts in Steps 4-8 Now)
(Make sure that the cable is routed between pulley 8 and the cable retainer bolt.)
Assembly Steps are continued on page 15
Page 14
Pulley-8
Pulle
y
-9
Floating Pulley
Bracket
STEP 4 STEP 5
Cable Adapter
STEP 6
STEP 7
Floating Dual
Pulley Bracket
Cable
Retainer
Bolt
STEP 8

2 – 5” Hex Bolts Leg Press Base
4– 3/8” Flat Washers
2 – 3/8” Lock Nuts
Dual Pulley Mount
Press Arms
short end of tube
faces outward
1 – 1/2” x 10 ¾” Hex Bolt
2 – 1/2” Flat Washers
1 – 1/2” Lock Nut
Caution: Press arms are unstable until the
cables are attached. It is recommended to
lay the press arms forward onto a protective
surface until the cables are installed.
Step 1: Attach Dual Pulley Mount to Leg Press Base using:
Two (3/8” x 5” Hex Bolts)
Four (3/8” Flat Washers)
(Wrench Tighten Bolts) Two (3/8” Lock Nuts)
Step 2: Attach Press Arms to Leg Press Base using:
One (1/2” x 10 ¾” Hex Bolt)
Two (1/2” Flat Washers)
One(1/2”LockNut)
(Wrench Tighten Bolts, Assembly Should Move Freely.)
Note: Leg Press Arms angle outward from Leg Press Frame,
short end of tube faces outward.
Page 15
STEP 1
STEP 2

2– 3 ½” Pulleys 1 – 3 ½” Pulley
2– 2” Hex Bolts 1– 2” Hex Bolt
4– 3/8” Flat Washers 2 – 3/8” Flat Washers
2 – 3/8” Lock Nuts 1 – 3/8” Lock Nut
1– 8” Hex Bolt 2– 3 ½” Pulleys 2 – 3 ½” Pulleys
2 – 3/8” Small OD 2– 2” Hex Bolts 2–1 ¾” Hex Bolts
Washers 4– 3/8” Flat Washers 2 – 3/8” Flat Washers
1– 3/8” Lock Nuts 2– 3/8” Lock Nuts
Step 3: Attach Pulleys 1 & 2 to Press Arms using: Two (3 ½” Pulleys)
Two (3/8” x 2” Hex Bolts)
Four(3/8”FlatWashers)
(Wrench Tighten Bolts) Two (3/8” Lock Nuts)
Step 4: Attach Pulleys 3 & 4 to Leg Press Base using: Two (3 ½” Pulleys)
Two (3/8” x 1 ¾” Hex Bolts)
(Wrench Tighten Bolts) Two (3/8” Flat Washers)
Step 5: Attach Pulleys 5 & 6 to Pulley Bracket using: Two (3 ½” Pulleys)
Two (3/8” x 2” Hex Bolts)
Four (3/8” Flat Washers)
(Wrench Tighten Bolts) Two (3/8” Lock Nuts)
Step 6: Attach Pulley 7 to Floating Pulley Bracket using: One (3 ½” Pulley)
One (3/8” x 2” Hex Bolt)
Two (3/8” Flat Washers)
(Wrench Tighten Bolts) One (3/8” Lock Nut)
Step 7: Attach Main Cable by sliding end of cable thru slot of Cable End as shown,
then slide Bushing into Cable End, attach Bolt. Route the Main Cable around
Pulleys 1, 3, 5 and thru Floating Pulley 7, continue routing cable around Pulleys 6,
4, 2 and attach other end of cable to Cable End using:
One (3/8” x 8” Hex Bolt)
Two(3/8”SmallODWashers)
(Wrench Tighten Bolts) One (3/8” Lock Nut)
Page 16
STEP 5
STEP 4STEP 3
Pulley-3 & 4
Pulley-5 & 6
Pulley-1 & 2
STEP 6
Pulley-7
Cable
Cable End
w/ Bushing
STEP 7

Orthopedic Pad
Seat Base
Assembled
Back & Seat Pad
Step 8: Place Orthopedic Pad on Seat Base. Work the edge of pad into the groove
of the Seat base on all sides. Do not use sharp objects during
installation.
Press Arm Stops Floating Pulley Stop
Step 9: Cable Adjustment
Screw Press Arm Stops up or down to remove slack in Main Cable, tighten the Jam Nuts.
Make sure both Press Arm Stops are adjusted to the same height; otherwise it might be
difficult to insert the Press Arm Locking Rod later. Next, adjust the Floating Pulley Stop out
until it contacts the Floating Dual Pulley Bracket as shown in the diagram. Tighten jam
nuts on the floating pulley stop. After first weeks use and as needed, adjust cable slack
by alternately adjusting the Floating Pulley Stop and Press Arm Stops.
Page 17
STEP 8
Floating Dual
Pulley Bracket

2 – 1” Hex Bolts
2 – 3/8” Flat Washers
2 – 2 ½” Hex Bolts
4 – 3/8” Flat Washers
2 – 3/8” Lock Nuts
2 – 2 ½” Hex Bolts
2 – 3/8” Flat Washers
Step 10: Attach Handles to Leg Press Base using:
Two (3/8” x 2 ½” Hex Bolts)
Four (3/8” Flat Washers)
(Wrench Tighten Bolts) Two (3/8” Lock Nuts)
Step 11: Attach Back Pad to Back Pad Stem using:
Two (3/8” x 1” Hex Bolts)
(Wrench Tighten Bolts) Two(3/8”FlatWashers)
Step 12: Attach Seat Pad to Leg Press Base using:
Two (3/8” x 2 ½” Hex Bolts)
(Wrench Tighten Bolts) Two(3/8”FlatWashers)
Page 18
STEP 12
STEP 10
STEP 11
Handles
Back Pad
Seat Pad
Back Pad Stem
To these sets of holes
Attach Seat & Handle
For more Leg Room
To these sets of holes
Attach Seat & Handle
For more Pre-Stretch