Inspire LEG PRESS OPTION Supplement

ASSEMBLY & OPERATION MANUAL
LEG PRESS OPTION
RECORD SERIAL NUMBER HERE
www.inspirefitness.net by Health In Motion LLC Sept. 2006

TABLE OF CONTENTS
Section Description………………………………………………….. Page
Instructions………………………………………………………………….. 1
Tools Requires……………………………………………………………… 1
Parts & Hardware List………………………………………………….. 2
Hardware Sizing Chart ………………………………………………… 3
Assembly Instructions (M1 & M2)……………………………….. 4-10
Assembly Instructions (M3)………….…………………………….. 11-16
Decal Reference……………………………………………………………. 17
Decal Placement…………………………………………………………… 18
General Maintenance Information…….………………………… 19
Maintenance Schedule…….………………………………………….. 20
Limited Warranty.………………………….……………………………. 21

BEFORE ASSEMBLING YOUR LEG PRESS
IMPORTANT: Read this entire manual before attempting to build or use
your leg press. This manual contains step by step instructions for proper
assembly.
Use the parts list included in this manual to verify that all parts are
accounted for before assembly. If any parts are missing, contact the retailer
of this home gym for replacement parts. Or, call Inspire at 714-738-1729
Service of your home gym should only be preformed by an authorized
INSPIRE retailer. Service preformed by anyone else can result in loss of
warranty. Use only Inspire replacement parts on this machine. The use of
any other brand of parts can also result in a loss of warranty. If you need
help finding an authorized retailer, please contact us directly:
Inspire Fitness
637 S. State College Blvd.
Fullerton, CA 92831
Ph: 714-738-1729
Fx: 714-738-1728
www.inspirefitness.net
TOOLS REQUIRED FOR ASSEMBLY
• Standard socket set (including 9/16” and 1/2” sockets)
• 9/16” wrench
• Adjustable wrench
• Tape Measure
• Rubber Mallet
PAGE 1

PARTS & HARDWARE LIST
Item Parts Description Qty Qty
Rec'd Item Hardware Description Qty Qty Rec'd
1 Leg Press Base 1 1 Bolt, 3/8-16 x 1" L 2
2 Press Arm 1 2 Bolt, 3/8-16 x 2" L 6
3 Foot Plate 1 3 Bolt, 3/8-16 x 2 1/4" L 2
4 Handles 1 4 Bolt, 3/8-16 x 2 1/2" L 2
5 Attachment Arm 1 5 Bolt, 3/8-16 x 3 3/4" L 3
6 Back Pad Stem 1 6 Bolt, 3/8-16 x 4 1/4" L 3
7 Floating Pulley Bracket Assembly 1 7 Bolt, 3/8-16 x 4 3/4" L 1
8 Orthopedic Pads 2 8 Bolt, 3/8-16 x 5" L 3
9 LP1 Cable 1 9 Bolt, 1/2-13 x 5" L 1
10 Seat Base 2
11 3 1/2" Pulley 5 10 3/8" Washer 29
11 1/2" Washer 2
12 3/8-16 Locknut 13
13 1/2-13 Locknut 1
14 Step Spacer, 1" Long 2
15 Barrel Spacer, 5/16” Long 1
16 Cable Adapter 1
17 Pivot Shaft 1
18 4 mm Wrench 1
PAGE 2
NOTE: There May Be Extra Parts Left Over Depending On Which Machine
You Attach the LP1 Too.

HARDWARE SIZING CHART
PAGE 3
3/8" DIA. Bolt Allen Wrench
3/8" Washer 1/2" Washer Step Spacer
1/2" Locknut 3/8" Locknut 5/16" Barrel Spacer
1/2" DIA. Bolt
ACTUAL PARTS MAY BE SMALLER OR LARGER THAN SHOWN
Pivot Shaft
1" 2" 3" 4" 5" 6" 7"

ASSEMBLY INSTRUCTIONS
PAGE 4

STEP 1
Assembly Procedure for Attaching Leg Press to M1 & M2
Go directly to page 11 if attaching Leg Press to M3
NOTE: The Leg Press may be attached to either side of the machine.
The pictures show only one side
Lower Cable
Pulley 1
Disconnect Cable and
Remove Pulley 1
Step 1: Remove Pulley 1 and disconnect lower cable from Home Gym. Retain pulley 1
and hardware for future steps.
Page 5

STEP 5
Leg Press Base
2 – 5” Hex Bolts
4 – 3/8” Flat Washers
1 – 4 ¼” Hex Bolt 2 – 3/8” Lock Nuts
1 – 3/8” Flat Washer
Press Arm Attachment Arm
Pulley 1
1 – 3 ½” Pulley
1 – 2” Hex Bolt
2 – 3/8” Flat Washers
1 – Pivot Shaft 1 – 3/8” Lock Nut
2 – 5” Hex Bolts
Home Gym 4 – 3/8” Flat Washers
2 – 3/8” Lock Nuts
Step 2: Attach Pulley 1 to Leg Press Base using: One (3 ½” Pulley)
(Wrench Tighten) One (2” Hex Bolt)
Two(3/8”FlatWashers)
One(3/8”LockNut)
Step 3: Secure Attachment Arm to Home Gym using: Two (5” Hex Bolts)
(Finger Tighten Only) Four (3/8” Flat Washers)
Two(3/8”LockNuts)
Step 4: Secure Attachment Arm to Leg Press Base using: Two (5” Hex Bolts)
(Finger Tighten Only) Four (3/8” Flat Washers)
Two(3/8”LockNuts)
Step 5: Secure tubular portion of Attachment Arm to
LegPressBaseusing:One (4 ¼” Hex Bolt)
(Wrench Tighten bolts in steps, 3, 4, & 5 Now) One (3/8” Flat Washer)
Step 6: Attach Press Arm to Leg Press Base using: One (Pivot Shaft)
(Tighten Allen Screws using 4mm Allen Wrench Included)
Page 6
STEP 3
STEP 4
STEP 2
STEP 6

1 – Cable Adapter
Floating Pulley Bracket Assembly
Pulley 2 Pulley 3
1 – 3 ½” Pulley
1 – 3 ½” Pulley 2 – 3 ¾” Hex Bolts
1 – 4 ¾” Hex Bolt 1 – 2” Hex Bolt 2 – 1“ Step Spacers
2 – 3/8” Flat Washers 2 – 3/8” Flat Washers 2 – 3/8” Flat Washers
1 – 3/8” Lock Nut 1 – 3/8” Lock Nut 2 – 3/8” Lock Nuts
Step 7: Attach Pulley 2 to Arm Assembly using: One (3 ½” Pulley)
(Wrench Tighten Bolt) One (2” Hex Bolt)
Two(3/8”FlatWashers)
One(3/8”LockNuts)
Step 8: Attach Pulley 3 and retainer bolt to Base using: One (3 ½” Pulley)
(Wrench Tighten Bolts) Two (3 ¾” Hex Bolt)
Two(1”StepSpacers)
Two(3/8”FlatWashers)
Two(3/8”LockNuts)
Step 9: Attach Cable End to Leg Press Base using: One (4 ¾” Hex Bolt)
(Wrench Tighten Bolt) Two (3/8” Flat Washers)
(Run Cable as shown in diagram. Make sure that the cable One (3/8” Lock Nut)
is routed between pulley 3 and the cable retainer bolt.)
Step 10: Attach Floating Pulley Bracket Assy to Cable Using: One (Cable Adapter)
Thread the cable end through the hole in the Floating Pulley Bracket Assy and attach Cable
Adapter, as shown in diagram above. This will prevent the cable end from pulling through.
Page 7
STEP 7 STEP 8
STEP 9
STEP 10

Home Gym Lower Cable
1 – 3 ½” Pulley
1 – 2” Hex Bolt
2 – 3/8” Flat Washers
1 – 3/8” Lock Nut
Pulley 4
1 – 3 ½” Pulley
1 – 2” Hex Bolts
2 – 3/8” Flat Washers
1– 3/8” Lock Nuts
Pulley 5 1 – 2” Hex Bolt
2 – 3/8” Washers
1 – 3/8” Lock Nut
1 – 2” Hex Bolt
2 – 3/8” Flat Washers
1 – 3/8” Lock Nut
Step 11: Attach Pulley 4 to Attachment Arm using: One (3 ½” Pulley)
(Wrench Tighten Bolt) One (2” Hex Bolt)
Two(3/8”FlatWashers)
One(3/8”LockNut)
Step 12: Attach Pulley 5 to Floating Pulley Bracket Assy using:
(Wrench Tighten Bolt) One (3 ½” Pulley)
One (2” Hex Bolt)
Two(3/8”FlatWashers)
One(3/8”LockNut)
Step 13: Thread Home Gym Lower Cable around Pulleys 4 & 5 as
shown in diagram and attach to Leg Press using: One (2” Hex Bolt)
(Wrench Tighten Bolt) Two (3/8” Flat Washers)
One(3/8”LockNut)
Step 14: Attach Retainer Bolt to Attachment Arm using: One (2” Hex Bolt)
(Wrench Tighten Bolt) Two (3/8” Flat Washers)
(Make sure that the cable is routed between pulley 4 and the One (3/8” Lock Nut)
cable retainer bolt.)
Page 8
STEP 11
STEP 12
STEP 13
STEP 14

Orthopedic Pad
Seat Base
Assembled
Back & Seat Pad
Step 15: Place Orthopedic Pad on Seat Base. Work the edge of pad into the groove
of the Seat Base on all sides. Do not use sharp objects during
installation.
Press Arm Leg Press Base
Press Arm Floating Pulley
Jam Nut Jam Nut
Step 16:
Cable Adjustment
Thread the press arm stop so that there is one inch between the Press Arm and the Leg
Press Base, as shown in the diagram. Tighten the Jam Nut. Next thread the floating
pulley stop out until it contacts the floating pulley as shown in the diagram. Tighten jam
nuts on the floating pulley stop. After first weeks use and as needed, adjust cable slack
by alternately adjusting the floating pulley stop and press arm stop.
Page 9
STEP 15

BackPadStem
2 – 1” Hex Bolts
2 – 3/8” Flat Washers
2 – 2 ½” Hex Bolts
4 – 3/8” Flat Washers
Back Pad 2 – 3/8” Lock Nuts
Handles
Seat Pad Leg Press Base
Foot Plate
1 – 5” Hex Bolts
2 – ½” Flat Washers 2 – 2 ¼” Hex Bolts
1 – ½” Lock Nut 2 – 3/8” Flat Washers
Step 17: Attach Handles to Leg Press Base using: Two (2 ½” Hex Bolts)
(Wrench Tighten Bolts) Four (3/8” Flat Washers)
Two(3/8”LockNuts)
Step 18: Slide Back Pad Stem into Leg Press Base, Then
Attach Back Pad to Back Pad Stem using: Two (1” Hex Bolts)
(Wrench Tighten Bolts) Two(3/8”FlatWashers)
Step 19: Attach Seat Pad to Leg Press Base using: Two (2 ¼” Hex Bolts)
(Wrench Tighten Bolts) Two(3/8”FlatWashers)
Step 20: Attach Foot Plate to Press Arm using: One (½”X 5” Hex Bolt)
(Wrench Tighten Bolt) Two (½” Flat Washers)
One (½” Lock Nut)
Page 10
STEP 17
STEP 18
STEP 19
STEP 20

STEP 1
STEP 2
STEP 3
Assembly Procedure for Attaching Leg Press to M3
NOTE: The Leg Press may be attached to either side of the machine.
The picture shows only one side.
Disconnect Middle Cable
Middle Cable
Remove Pulley 1 & 1” Barrel Spacer
From M3 Base Frame
Pulley 1 &
1” Barrel Spacer
Remove the Swivel Pulley
Bracket from M3 Base Frame
Swivel Pulley Bracket
M3 Main Upright
Step 1: Remove the Swivel Pulley Bracket from the M3 Main Upright. Leave the cable
connected to the Swivel Pulley. Save Washers and Locknuts for later use.
Step 2: Remove Pulley 1 and 1” Long Barrel Spacer from M3 Main Upright.
Save Parts for later use.
Step 3: Disconnect the Middle Cable from the Main Upright. Re-install Bolt, Washers, and
Locknut. Wrench tighten bolt.Page 11

STEP 5
STEP 6
Pulley 1 &
1” Barrel Spacer
Swivel Pulley
Pulley 2 Bracket
Attachment Arm
1 – 3 ½” Pulley
1 – 2” Hex Bolt
2 – 3/8” Flat Washers
1 – 3/8” Lock Nut
Step 4: Attach Pulley 2 to Leg Press Base using:
Two (3/8” Flat Washers) One (3 ½” Pulley)
One (3/8” Lock Nut) One (2” Hex Bolt)
(Wrench Tighten)
Step 5: Secure Attachment Arm & Swivel Pulley Bracket to Main Upright using:
Two (4 ¼” Hex Bolts) Two (3/8” Lock Nuts)
Four (3/8” Flat Washers)
(Finger Tighten Only)
Step 6: Secure attachment arm to main upright using:
One (3 ½” Pulley) One (5/16” Barrel Spacer) One (1” Barrel Spacer)
One (3 ¾” Hex Bolt) Two (3/8” Flat Washers) One (3/8” Lock Nut)
Note: Re-install Pulley 1 and 1” Barrel Spacer in original location
(Finger Tighten Only)
Step 7: Secure Attachment Arm to Leg Press Base using: Two (5” Hex Bolts)
(Finger Tighten Only) Four (3/8” Flat Washers)
Two(3/8”LockNuts)
Step 8: Secure tubular portion of Attachment Arm to Leg Press Base Using:
(Wrench Tighten Bolts in Steps 5-8 Now) One (4 ¼” Hex Bolt)
One(3/8”FlatWasher)
Step 9: Attach Press Arm to Leg Press Base using: One (Pivot Shaft)
(Tighten Allen Screws using 4mm Allen Wrench Included)
Page 12
STEP 4
STEP 7
STEP 9
STEP 8 5/16” Barrel Spacer
Press Arm
1 – 4 ¼” Hex Bolt
1 – 3/8” Flat Washer
2 – 5” Hex Bolts
2 – 3/8” Lock Nuts
4
–
3/8” Flat Washers
Leg Press Base
1 – Pivot Shaft
2 – 4 ¼”Hex Bolts
4 – 3/8” Flat Washers
2 – 3/8” Lock Nuts
1 – 3 ¾” Hex Bolt
1 – 5/16” Barrel Spacer
1 – 3/8” Lock Nut
2
–
3/8” Flat Washers

1 – Cable Adapter
Floating Pulley Bracket Assembly
Press Arm
Pulley 3 Pulley 4
1 – 3 ½” Pulley
1 – 3 ½” Pulley 2 – 3 ¾” Hex Bolts
1 – 4 ¾” Hex Bolt 1 – 2” Hex Bolt 2 – 1“ Step Spacers
2 – 3/8” Flat Washers 2 – 3/8” Flat Washers 2 – 3/8” Flat Washers
1 – 3/8” Lock Nut 1 – 3/8” Lock Nut 2 – 3/8” Lock Nuts
Step 10: Attach Pulley 3 to Press Arm using: One (3 ½” Pulley)
(Wrench Tighten Bolt) One (2” Hex Bolt)
Two(3/8”FlatWashers)
One(3/8”LockNuts)
Step 11: Attach Pulley 4 and retainer bolt to Base using: One (3 ½” Pulley)
(Wrench Tighten Bolts) Two (3 ¾” Hex Bolt)
Two(1”StepSpacers)
Two(3/8”FlatWashers)
Two(3/8”LockNuts)
Step 12: Attach Cable End to Leg Press Base using: One (4 ¾” Hex Bolt)
(Wrench Tighten Bolt) Two (3/8” Flat Washers)
(Run Cable as shown in diagram. Make sure that the cable One (3/8” Lock Nut)
is routed between pulley 4 and the cable retainer bolt.)
Step 13: Attach Floating Pulley Bracket Assy to Cable Using: One (Cable Adapter)
Thread the cable end through the hole in the Floating Pulley Bracket Assy and attach Cable
Adapter, as shown in diagram above. This will prevent the cable end from pulling through.
Page 13
STEP 10 STEP 11
STEP 12
STEP 13

Middle Cable
Pulley 5
1 – 3 ½” Pulley
1 – 2” Hex Bolt
2 – 3/8” Flat Washers
1 – 3/8” Lock Nuts
Pulley 6
1 – 3 ½” Pulley
1 – 2” Hex Bolt 1 – 2” Hex Bolt 1 – 2” Hex Bolt
2 – 3/8” Flat Washers 2 – 3/8” Flat Washers 2 – 3/8” Flat Washers
1 – 3/8” Lock Nut 1 – 3/8” Lock Nut 1 – 3/8” Lock Nut
Step 14: Attach Pulley 5 to Attachment Arm using: One (3 ½” Pulley)
(Wrench Tighten Bolt) One(2”HexBolt)
Two(3/8”FlatWashers)
One(3/8”LockNut)
Step 15: Attach Pulley 6 to Floating Pulley Bracket Assy using: One (3 ½” Pulley)
(Wrench Tighten Bolt) One(2”HexBolt)
Two(3/8”FlatWashers)
One(3/8”LockNut)
Step 16: Thread Middle Cable around Pulleys 5 & 6 as shown in
Diagram and attach to Leg Press using: One (2” Hex Bolt)
(Wrench Tighten Bolt) Two (3/8” Flat Washers)
One(3/8”LockNut)
Step 17: Attach Retainer Bolt to Attachment Arm using: One (2” Hex Bolt)
(Wrench Tighten Bolt) Two (3/8” Flat Washers)
One(3/8”LockNut)
(Make sure that the cable is routed between pulley 5 and the cable retainer bolt.)
Page 14
STEP 14
STEP 15 STEP 16 STEP 17

Orthopedic Pad
Seat Base
Assembled
Back & Seat Pad
Step 18: Place Orthopedic Pad on Seat Base. Work the edge of pad into the groove
of the Seat Base on all sides. Do not use sharp objects during
installation.
Press Arm Leg Press Base
Press Arm Floating Pulley
Stop Stop
Step 19:
Cable Adjustment
Thread the press arm stop outward until cable is taut. Tighten the Jam Nut. Next thread
the floating pulley stop outward until it contacts the floating pulley as shown in the
diagram. Tighten jam nut on the floating pulley stop. After first weeks use and as
needed, adjust cable slack by alternately adjusting the floating pulley stop and press arm
stop.
Page 15
STEP 18
STEP 19

Back Pad Stem
2 – 1” Hex Bolts
2 – 3/8” Flat Washers
2 – 2 ½” Hex Bolts
Back Pad 4 – 3/8” Flat Washers
2 – 3/8” Lock Nuts
Handles
Seat Pad
Foot Plate
Leg Press Base
1 – ½” x 5” Hex Bolt
2 – ½” Flat Washers
1 – ½” Lock Nut
2 – 2 ¼” Hex Bolts
2 – 3/8” Flat Washers
Step 20: Attach Handles to Leg Press Base using: Two (2 ½” Hex Bolts)
(Wrench Tighten Bolts) Four (3/8” Flat Washers)
Two(3/8”LockNuts)
Step 21: Slide Back Pad Stem into Leg Press Base, Then
Attach Back Pad to Back Pad Stem using: Two (1” Hex Bolts)
(Wrench Tighten Bolts) Two (3/8” Flat Washers)
Step 22: Attach Seat Pad to Leg Press Base using: Two (2 ¼” Hex Bolts)
(Wrench Tighten Bolts) Two (3/8” Flat Washers)
Step 23: Attach Foot Plate to Press Arm using: One (1/2” x 5” Hex Bolt)
(Wrench Tighten Bolts) Two (1/2” Flat Washers)
One(1/2”LockNut)
Page 16
STEP 20
STEP 21
STEP 22
STEP 22

DECAL REFERENCE
PAGE 17

DECAL PLACEMENT
PAGE 18
“WARNING, PINCH
POINTS” between
press pedals, on
leg press arm (60 x
40)
Serial number
label (60 x 40)