Inspire DUAL INNER/OUTER THIGH Supplement

ASSEMBLY & OPERATION MANUAL
Dual INNER/OUTER THIGH
RECORD SERIAL NUMBER HERE
www.inspirefitness.com by Health In Motion LLC 7-3-19

CONGRATULATIONS… You’ve just taken the first step to a healthier
and stronger body. This Dual Inner/Outer Thigh machine by Inspire offers
the key to unlocking your body’s potential. Regular strength training on a
multi-gym has been shown to deliver a host of benefits including: increased
muscle tone, decreased body fat, improved energy levels, a reduction in
stress, and improved cardiac output. Once again, congratulations, you are
on your way to improving your self image, overall health, and quality of life.
BEFORE ASSEMBLING YOUR INNER OUTER
IMPORTANT: Read this entire manual before attempting to build or use
this Dual Inner/Outer Thigh machine. This manual contains step by step
instructions for proper assembly.
Use the parts list included in this manual to verify that all parts are
accounted for before assembly. If any parts are missing, contact the dealer
of this Dual Inner/Outer Thigh machine for replacement parts or call Inspire
at 877-738-1729.
Make sure that adequate room has been cleared before attempting to build
your Dual Inner/Outer Thigh machine. A rubber mat is recommended for
use under your Dual Inner/Outer Thigh machine to protect wood flooring or
carpeting from damage during assembly and usage. In a multi-use setting
or commercial setting, it is recommended that the machine be bolted to the
floor through the holes in the base plates.
This Dual Inner/Outer Thigh machine is intended for indoor use only. Rust
can form on certain parts in a humid environment resulting in impaired
function.
Service of your Dual Inner/Outer Thigh machine should only be preformed
by an authorized Inspire dealer. Service preformed by anyone else can
result in loss of warranty. If you need help finding an authorized dealer,
please contact us directly:
Inspire Fitness
255 Airport Circle
Suite 101
Corona, CA 92880
Ph: 877-738-1729
Fx: 714-738-1728
www.inspirefitness.com

TABLE OF CONTENTS
Section Description……………………………………………………. Page
Important Safety Instructions………………………………………. 1
Tools Required………………………………………………………………… 1
Parts & Hardware List……………………………………………………. 2
Cable Charts…………….……………………………………………………. 3
Assembly Instructions……………………………………………………. 4
Cable Adjustment…………………………………………………………… 19
Decal Reference……………………………………………………………… 20
Decal Placement…………………………………………………………….. 22
Training Tips…………………………………………………………………… 23
General Maintenance Information…….…………………………… 24
Maintenance Schedule…….……………………………………………… 25
Limited Warranty…………………………………………………………….. 26

Page 1
IMPORTANT SAFETY INSTRUCTIONS
Please read this entire manual and familiarize yourself with all decals and
warnings before using this Dual Inner/Outer Thigh machine.
• WARNING! It is necessary to inspect this Dual Inner/Outer Thigh
machine regularly to maintain safety and proper function. Please use the
maintenance schedule included towards the back of this manual.
Immediately replace any and all defective or worn parts. Pay special
attention to moving parts such as the cables and pulleys and connections
to accessories. See General Maintenance section for complete details.
• Use this Dual Inner/Outer Thigh machine for its intended purpose as
described in this Operation Manual or the Exercise Book. Do not use
attachments not recommended by the manufacturer.
• Make sure bystanders are at least 5 feet away from the Dual Inner/Outer
Thigh machine while it is in use.
• Keep children off the Dual Inner/Outer Thigh machine at all times.
• Keep the Dual Inner/Outer thigh machine away from walls and clear of
any obstructions.
• Stop immediately if you experience shortness of breath, pain, or dizziness
during your workout. Inspire strongly recommends consulting your
doctor before starting an exercise program.
TOOLS REQUIRED FOR ASSEMBLY
• Metric socket set (13mm,16mm, 17mm, 18mm, and 19mm sockets)
• Metric wrenches (13mm, 16mm, 17mm, 18mm, and 19mm)
•4mm, 5mm, and 6mm Allen wrenches (supplied in hardware pack)
• Adjustable wrench

Page 2
Item Parts Description Qty Qty Rec'd Item Hardware Description Qty Qty Rec'd
1 Main Frame 1 1 M10 x 25 Hex Bolt 2
2 Guide Cable Support 1 2 M10 x 95 Hex Bolt 2
3 Upright 1 1 3 M10 x 75 Hex Bolt 8
4 Rear Foot 1 4 M12 x 130 Hex Bolt 1
5 Base Frame 1 5 M6 x12 Button Head Bolt 8
6 Top Weight/Selector Stem 2 6 M10 x 125 Hex Bolt 2
7 Selector Handle 1 7 M10 x 50 Hex Bolt 1
8 Rubber Donut 4 8 M10 x 50 Threaded HexBolt 3
9 Top Weight Stop Assembly 2 9 M10 x25 Button Head Bolt 3
10 Guide Rods 4 10 M10 x90 HexBolt 4
11 Upper Pulley Mount, Left 1 11 M8 x 20 HexBolt 2
12 Upper Pulley Mount, Right 1 12 M8 x 12 Button Head Bolt 9
13 Cable Connector 1 13 M10 x25 Counter Sunk Bolt 4
14 Back Pad Mount 1 14 M10 x70 HexBolt 7
15 Back Pad 1 15 M8 x 100 HexBolt 1
16 Seat Pad 1 16 M8 x 20 Button Head Bolt 6
17 Thigh Pad Mount 2 17 M8 x 70 Button Head Bolt 2
18 Shaft Collar 2
19 Thigh Pad 2 18 M10 Flat Washer 38
20 Rear Shroud Plate Support 1 19 M8 Flat Washer 20
21 Metal Shroud Placard Left 1 20 M6 Flat Washer 8
22 Metal Shroud Placard Right 1 21 M10 Large OD Flat Washer 2
23 Left Metal Shroud Plate 1 22 M12 Washer 2
24 Right Metal Shroud Plate 1
25 Upper Metal Shroud 1 23 M10 Locknut 13
26 Lower Metal Shroud 1 24 M8 Locknut 3
27 Fabric Shroud 1 25 M12 Locknut 1
28 Rubber Cup 2 26 Slotted Cable Bolt 2
29 Rubber Tablet Holder 1
30 Molded Top Cap 1 27 Weight Pin 2
31 Guide Rod Lube 1 28 4 mm Allen Wrench 1
32 Touch-up Paint 1 29 5 mm Allen Wrench 1
33 Main Cable 1 30 6 mm Allen Wrench 1
34 Guide Cable 2
35 Weight Stack Cable 2
36 3 1/2" Pulley 4
37 4 1/2" Pulley 3
DUAL Inner/Outer PARTS & HARDWARE LIST

Page 3
Weight Cable p/n GM 882-500-002
1396 mm
1411 mm
2736 mm
Main Cable p/n GM 888-500-001
Guide Cable p/n GM 882-500-001
Cable lengths could change at any time without notice.
Cable lengths are in millimeters and for reference only.
DUAL LINE INNER/OUTER CABLE CHART

Page 4
ASSEMBLY INSTRUCTIONS

Page 5
Step 1: Attach Upright 1 to the Main Frame using: 2 - M10 x 25 Hex Bolts
2 - M10 x 95 Hex Bolts
NOTE: Finger Tighten Only.6 - M10 Flat Washers
2 - M10 Locknuts
Step 2: Attach Guide Cable Support to Main Frame
and Upright 1 using: 4 - M10 x 75 Hex Bolts
8 - M10 Flat Washers
4 - M10 Locknuts
NOTE: Finger Tighten Only.
2 - M10 x 25 Hex Bolts
2 - M10 x 95 Hex Bolts
6 - M10 Flat Washers
2 - M10 Locknuts
Step 1
Step 2
4 - M10 x 75 Hex Bolts
8 - M10 Flat Washers
4 - M10 Locknuts
Upright 1
Guide Cable
Support
Main Frame

Page 6
Step 3: Attach the Rear Foot to Base Frame using: 2 - M10 x 75 Hex Head Bolts
4 - M10 Flat Washers
2 - M10 Locknuts
NOTE: Wrench Tighten Now.
Step 4: Attach the Base Frame to Upright 1 using: 1 - M10 x 70 Hex Head Bolts
2–M10 x 125 Button Head Bolt
6 - M10 Flat Washers
3 - M10 Locknuts
NOTE: Wrench Tighten Now.
Step 3
2 - M10 x 75 Flat Head Bolts
4 - M10 Flat Washer
2 - M10 Lock Nuts
Step 4
2–M10 x 125 Button Head Bolts
1 - M10 x 70 Flat Head Bolts
6 - M10 Flat Washers
3 - M10 Locknuts
Rear Foot
Upright 1

Page 7
A
Step 5: Attach the Selector Handle to Left Arm Assembly using: 1 - M12 x 130 Hex Head Bolts
2 - 10 x 5 Shoulder Bolts
2 - M12 Flat Washers
1 - M12 Locknuts
NOTE: Wrench Tighten The M12 Bolt To Secure The Selector Handle, But
Do Not Over Tighten. Selector Handle Must Move Freely.
Wrench Tighten The Shoulder Bolts.
Step 5
1 - M12 x 130 Hex Bolt
2 - 10 x 5 Shoulder Bolts
2 - M12 Washers
1 - M12 Lock Nuts
Selector Handle
Left Arm Assembly
Left Arm Assembly

Page 8
Step 6: Insert two Guide Rods into the holes in the bottom tube of the Main Frame. Carefully tilt the
Guide Rods back away from the machine. Slide one Rubber Donut into each guide Rod. Slide ten
Weight Plates onto the Guide Rods. Make sure the recessed area on the front of the weight plate
is facing towards the front of the machine. Slide Top Weight/Selector Stem onto the Guide Rods.
Slide the Top Weight Stop Assembly onto the Guide Rods making sure the rubber pad is facing
down. Attach the Upper Pulley Mount, Top Weight Stop Assembly, and Guide Rods to the Main
Frame Using:
1 - M10 x 75 Hex Bolt
2 - M10 x 90 Hex Bolts
6 - M10 Flat Washers
3 - M10 Locknuts
NOTE: Finger Tighten Only. 1 - M8 x 20 Hex Bolt
1 - M8 Flat Washer
Step 7: Repeat Step 6 for Right side.
NOTE: Finger Tighten Only.
Step 6
2 - M10 x 90 Hex Bolts
1 - M10 x 75 Hex Bolt
1 - M8 x 20 Hex Bolt
6 - M10 Flat Washers
3 - M10 Locknuts
1 - M8 Flat Washer
Guide Rods
Top Weight/ Selector Stem
Weight Plates
Rubber Donuts
Main Frame
Upper Pulley
Mount,Left
Top Weight
Stop Assembly
Front of weight plate has recessed
area for the number sticker
Bottom of weight
plate has three feet

Page 9
Weight Cable p/n GM 882-500-002
Main Cable p/n GM 888-500-001
Step 8: Route the Main Cable through the upright and then install
Pulley 3 using: 1 - M10 x 50 Hex Bolt
2 - M10 Washers
1 - M10 Lock Nuts
NOTE: Wrench Tighten Now.
Step 9: On the Weight Cable, install the Hex Bolt end completely into the Selector Stem and tighten the
Jam Nut. Route the Weight Cable up over Pulley 1, then over and down Pulley 2. Be sure the
Weight Cable is routed between the pulleys and the cable retainer pins. Feed the end of the
Weight Cable through Cable Connector as shown, attach one Cable Adapter and pull the Weight
Cable back to seat the Cable Adapter. Repeat for the other side.
NOTE: The Cable Hex Bolts need to be threaded completely into the Selector Stems and the Jam
Nuts fully tightened to prevent the Cable Hex Bolts from coming loose.
Cable
Connector
Cable Adapters
Main
Cable
Weight Cables
Weight
Cable
Jam Nut
Selector Stem
Thread Bolt completely into Selector
Stem and tighten Jam Nut
Step 9
1 - M10 x 50 Hex Bolt
2 - M10 Flat Washers
1 - M10 Lock Nuts
Pulley 3
Pulley 1
Pulley 2
Step 8

Page 10
Step 10: Insert the eyelet end of the Guide Cable through the plastic bushing in the Cable Connector
Assembly. Attach one end of a Spring to the eyelet and the other end to the hole in the plate at
the bottom of Upright 1. Insert the bolt end into the hole in plate on the Guide Cable Support.
Make sure there is one jam nut on the bottom side the plate and the other jam nut is on the top
side of the plate. Tighten the top jam nut just enough to make the Guide Cable tight. Tighten
the bottom jam nut against the bottom of the plate so the bolt will not come loose during use.
Step 11: Attach the Rear Shroud Plate Support to Upright 1
and Main Frame using: 1 - M8 x 100 Hex Bolt
2 - M8 Flat Washers
1 - M8 Locknut
Optional: Insert one M10 x 50 Fully Threaded Bolt from Step 16 to hold/stabilize the
Rear Shroud Plate Support in place until top Shroud Plate is attached.
NOTE: Wrench tighten all hardware from Steps 2, 5, 6, 7and 11 now.
Step 10
Install Guide
Cables
Cable Connector
Assembly
Springs
Rear Shroud Plate Support
Step 11
1 - M8 x 100 Hex Bolt
2 - M8 Flat Washers
1 - M8 Locknut

Page 11
Step 12: Attach the Back Pad Mount to the Base Frame using: 2 –M8 x 70 Button Head Bolts
6 –M8 x 20 Button Head Bolts
10 –M8 Flat Washers
2 –M8 Locknuts
NOTE: Wrench Tighten Now.
Back Pad Mount
Base Frame
Step 12
2 –M8 x 70 Button Head Bolts
6 –M8 x 20 Button Head Bolts
10 –M8 Flat Washers
2 –M8 Locknuts

Page 12
Step 13: Attach the Seat Pad to the Base Frame and
Back Pad to Back Pad Mount using: 4 –M10 x 70 Hex Bolts
4 –M10 Flat Washers
Note: Wrench Tighten Now.
Step 13
4 –M10 x 70 Hex Bolts
4 –M10 Flat Washers
Base Frame
Back Pad Mount

Page 13
Step 14: Insert Thigh Pad Mount into Left Arm, followed by sliding Shaft
Collar onto Thigh Pad Mount and tighten Set Screws. Attach the
Thigh Pad to Thigh Pad Mount using: 2 –M10 x 25 Flat Head Screws
NOTE: Repeat for Right Arm and Thigh Pad Mount.
Thigh Pad
Mount
Left Arm
Shaft Collar
Step 14
2 –M10 x 25 Flat Head Screws

Page 14
Insert Shroud into Metal Pieces
Step 15: To install Fabric Shroud, start from one end of the Lower Metal Shroud and insert the Fabric
Shroud inwards as shown. Make sure to have the same orientation as shown or else the fabric
shroud will be installed backwards. Continue to pull the Fabric Shroud along the inside of the
Lower Metal Shroud until it approaches the other end.
Repeat above for the Upper Metal Shroud. Be sure to pull tight as fabric shroud is wrapped.
If ripples appear on the fabric shroud, stretch and smooth out the fabric shroud to give a nice
smooth consistency to the shroud.
Step 15
Upper Metal Shroud
Lower Metal Shroud
Fabric Shroud

Page 15
Step 16: Attach the Lower Metal Shroud to the Upright 1
and Main Frame using: 1 –M10 x 25 Button Head Bolt
2 –M10 x 70 Hex Bolts
NOTE: Wrench Tighten Now. 3 –M10 Flat Washers
Step 17: Attach the Upper Metal Shroud to the Guide
Cable Support and Main Frame using: 3 –M10 x 50 Fully Threaded Bolts
3 –M10 Flat Washers
NOTE: Tighten bolts until fabric shroud is tight.
Step 16
1 –M10 x 25 Button Head Bolt
2 –M10 x 70 Hex Bolts
3 –M10 Flat Washers
Step 17
3 - M10 x 50 Fully Threaded Hex Bolts
3 - M10 Flat Washers
Shroud Assembly

Page 16
Step 18: Attach Right and Left Metal Shroud Plates
to Upright 1 using: 8 –M6 x 12 Button Head Bolts
8 –M6 Flat Washers
NOTE: Wrench Tighten Now.
Step 18
8 –M6 x 12 Button Head Bolts
8 –M6 Flat Washers
Right Metal Shroud
Plate

Page 17
Step 19: Attach the Left and Right Metal Shroud Placard to the
Upper Metal Shroud using: 6 –M8 x 12 Button Head Bolts
6 –M8 Flat Washers
NOTE: Wrench Tighten Now.
Step 19
6 - M8 x 12 Button Head Bolts
6 - M8 Flat Washers
Metal Shroud Placard, Left
Upper Metal Shroud