Ironwood GLACIER CDCPU User manual

0307
CIRCULATION DESK
CDCPU
CPU HOLDER
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a
carpeted surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
BY

PARTS DIAGRAM
HARDWARE
A
Outside Panel 01051041 1 ea.
B
Inside Panel 01051041 1 ea.
C
Top/Bottom 01051001 2 ea.
H1 Minifix Cam 909810 8 ea. H2 Minifix Bolt 909834 8 ea.
H4 #8 x 1-1/4"
Panhead Screw 901212 7 ea.
H3 Dowel 195000 8 ea.

Place the Top (C) and Bottom (C) on a clean, carpeted surface with the pre-drilled holes facing up.
Insert four Minifix Cams (H1) into the Top (C) with the arrows of the cams facing out.
#1
H1
ASSEMBLED DISASSEMBLED
Using the Minifix System:
Insert the Minifix Cams into the
appropriate holes with the arrow
facing outwards as shown.
Using the #2 Phillips screwdriver,
rotate the Cam Devices a half turn
clockwise until snug.
To disassemble, turn the Cam
Devices counter-clockwise and
remove panels.
When screwing post into hole, Do
Not over tighten. Screw post down
until bottom face of post flange just
touches board surface.
The CDCPU CPU Holder may be assembled for either a lefthand or righthand application.

Position the Inside Panel
(A) and Outside Panel (B)
as shown. Screw four
Minifix Bolts (H2) and insert
four Dowels (H3) into each
Panel where indicated.
#2
#3 Place Outside Panel (B) with the bolts facing up as shown. Position the Top/Bottom (C) onto the
Outside Panel as shown. Turn the arrows of the indicated Minifix Cams (H1) clockwise to secure.
#4 Position the Top/Bottom (C) with the edge as shown onto the Outside Panel (B) and turn the
arrows of the indicated cams (H1) clockwise to secure.
H2
H3

#6
With the assistance of another person, position the
CPU Holder unit into the selected side of the Desk
unit. Using three #8 x 1-¼" Panhead Screws (H4),
attach the Top (C) to the underside of the desk as
shown.
Do not fully tighten these screws yet!
#5 Position the Inside Panel (A) with the edge as shown onto the unit. Turn the arrows of the
cams (H1) of the Top (C) and the Bottom (C) clockwise to secure.
#7
Using four #8 x 1-¼" Panhead Screws (H4)
through the pre-drilled holes, attach the Outside
Panel (B) to the side of the desk as shown.
Tighten all screws (H4) at this time!
H4
H4