Ironwood PA3632 User manual

PA3632-PA3639
PATRON ACCESS
STATION
0720
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a carpeted
surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].

PARTS DIAGRAM
AB
C
G
D
Right Side-PA3632
Right Side-PA3639
01102541
01102641
1 ea.
1 ea.
Top 01102501 1 ea.
Back 01102552 1 ea.
Center Support 01012590 1 ea.
EK
Storage Shelf 01102532 1 ea. Keyboard Shelf 01102528 1 ea.
Left-PA3632
Left-PA3639
01102541
01102641
1 ea.
1 ea.

H8 Confirmat Screw 950100 2 ea.
H5 Rafix Bolt 909925 11 ea.
H4 Leveler 300870 4 ea.
H3 Leveler Insert 274650 4 ea.
H9 Grommet 286580 2 ea.
HARDWARE
H1 Rafix Cam 909909 18 ea. H2 Rafix Flush
Cam 909834 4 ea.
ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned

Place the Top (C),
Storage Shelf (E), and
Keyboard Shelf (K) on
a clean, carpeted
surface as shown. Tap
in Rafix Cams (H1)
into each panel where
indicated with the flat
edges aligned.
#1
C E
F
H1
H1
H1
H1
H1
H1
H1
K

Insert two rafix bolts (H5) into the
Top (C). Insert flush rafix cams
(H2) in the center support (G) and
place on rafix bolts and turn to
secure.
#2
H2
C
GH2
H5
H5
H5
H5
H5
H5
H5
H5
#3 Screw nine rafix Bolts (H5) into the Left Side (A) and Right Side (B) where
indicated.
Insert Leveler Inserts (H3) into the holes in the bottom edges
of Left Side (A) and Right Side (B) and tap into place. Screw
the Levelers (H4) into the Leveler Inserts.
Adjust the Levelers when the assembled unit is in place.
H3 H4
#4
H5 AB

Place the Left Side (A) with
the bolts facing up as shown.
Position the Back (D) onto the
Left Side (A) and turn the
cams (H1) to secure.
#6
Insert six rafix Cams (H1) into the Back (D)
#5
H1
D
A
H1
Position the Top (C) and Center Support Panel (G)
assembly onto the Left Side (A) and turn Rafix
Cams (H1) clockwise to secure.
Do not exceed 1/2 turn when tightening.
#7
A
D
C
G
H1

#8
A
D
F
H1
Position the Storage Shelf
(E) onto the Left Side (A)
and turn Rafix Cams (H1)
clockwise to secure.
#9
A
D
FE
H1
Position the Keyboard Shelf (K)
into the Left Side (A) and turn Rafix
Cams (H1) to secure.
Secure the Keyboard Shelf (K) to
the Center Support Panel (G) using
two Confirmat Screws (H8).
H8
H8
H8
K

Position the bolts of the Right
Side (B) onto the unit and turn
cams to lock in place.
There are nine Rafix Cams to
tighten
#10
B
With the help of another person,
turn the unit upright.
Insert Grommets (H9) into the top
(C) and the Storage Shelf (E).
#11
Your Glacire Patron Access Station is now fully assembled
and ready for use.
H9