Ironwood GLACIER PA6032 User manual

PA6032-PA6039
PATRON ACCESS
STATION
0720
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a carpeted
surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].
BY

PARTS DIAGRAM
AB
C
H
G
D
Right Side-PA6032
Right Side-PA6039
01102541
01102641
1 ea.
1 ea.
Top 01102701 1 ea.
Back 01102752 1 ea.
Divider 01102744 1 ea. Center Support 01012590 1 ea.
EK
Storage Shelf 01102732 1 ea. Keyboard Shelf 01102728 1 ea.
Left-PA6032
Left-PA6039
01102541
01102641
1 ea.
1 ea.
V
Left Support 01012788 1 ea.
W
Right Support 01012788 1 ea.

H8 Confirmat Screw 950100 8 ea.
H6 Rafix Bolt 909925 21 ea.
H4 Leveler 300870 4 ea.
H3 Leveler Insert 274650 4 ea.
H9 Grommet 286580 4 ea.
H1 Rafix Cam 909909 24 ea.
HARDWARE
H2 Rafix Flush
Cam 909834 12 ea.
ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned

E K H
C
H1
H1
H1
H1 H1
H1
H1 H1
H1
Place the Top (C) Divider (H), Storage Shelf (E), and Keyboard Shelf (K)
on a clean, carpeted surface as shown. Tap in Rafix Cams (H1) into each
panel where indicated with the flat edges aligned.
#1
H1

Screw two Rafix Bolts (H6) into the Top (C) where indicated.
#2
H6 C
H6
Insert Rafix Bolts and Flush Rafix Cams
V
G
C
W
#3 Place Rafix flush cams (H2) into center support (G), Left Support (V) and Right Support (W)
Then place rafix bolt (H6) into each hole in Top (C) to allow each support to sit upon. Place
each support and turn Rafix Flush cam to lock into place.
H6
H6
H6
H6
H6
H6
H6
H6
H6
#4 Screw nine Rafix Bolt (H6) into the Left Side (A) and Right Side (B) where
indicated.
.
H6
H2

Insert Leveler Inserts (H3) into the holes in the bottom
edges of Left Side (A) and Right Side (B) and tap into
place. Screw the Levelers (H4) into the Leveler Inserts.
Adjust the Levelers when the assembled unit is in
place.
#5
H3 H4
Screw four Rafix Bolts (H6) into the Back Panel (D) where indicated. Insert
six Rafix Cams (H1) into the Back with the arrows of the Cams facing out.
#6
H1
H1
H6
D
H6 H1
#7
D
A
H1
Place the Left Side (A) with the bolts facing up
as shown. Position the Back (D) onto the Left
Side and turn the cams (H1) secure.

#8
K
H1
A
D
Position the Keyboard Shelf (K) onto the
Left Side (A) as shown and turn Rafix
Cams (H1) clockwise to secure.
#9
K
H1
A
D
H8
H8
#10
H1
A
C
V
G
W
D
H1
Position the top (C) and Support Panel
(G, V, & W) assembly onto the Left Side
(A) and turn Rafix Cams (H1) clockwise
to secure.
Secure the Keyboard Shelf (K) to the Left
Support (V), Center Support (G), and Right
Support (W) using the Confirmat Screws (H8).
F
A
D
E
H1
H1
K
#11 Position the Storage Shelf (E) onto the
Left Side (A) and turn Rafix Cams (H1)
clockwise to secure.

#12 Position the Divider (H) onto the Top (C)
and turn Rafix Cams (H1) clockwise to
secure.
Secure the Divider (H) to the Storage Shelf
(E) using two Confirmat Screws (H8).
Position the bolts and dowels of the
Right Side (B) onto the unit and turn
cams clockwise to lock in place.
There will be six Rafix and three Minifix
Cams to tighten.
#13
H1 H
H8
H8
With the help of another person, turn the unit
upright.
Insert two Grommets (H9) each into the Top (C)
and the Storage Shelf (E).
C
E
H9
H9
H9
H9
H9
Your Glacier Patron Access Station
is now fully assembled and ready for use.
#14