Ironwood GLACIER CD36R User manual

CIRCULATION DESK
CD36R
RISER UNIT
0720
BY
IMPORTANT!
Assembly may require the assistance of
another person.
Before you begin assembly:
READ THE DIRECTIONS all the way through one
time. This will speed up the process and help you
understand the sequence of steps.
COUNT THE PARTS AND HARDWARE before
assembly. This ensures you have received all
necessary parts before you begin.
TOOLS: You may need a Phillips head screwdriver,
a medium slotted screwdriver or a plastic mallet. To
protect your new furniture from damage during
assembly, it is recommended to work on a carpeted
surface.
CAUTION: On assemblies requiring glue, make
sure the unit is assembled correctly before gluing.
Once this unit is assembled with glue, the
manufacturer will not be responsible for damaged
parts. Keep a damp cloth or sponge handy to wipe
off excess glue.
To care for this furniture, simply wipe with a cloth
dampened with glass cleaner containing ammonia-D.
In the event any parts are missing from
this package, send your name, address,
telephone number, and a description of
the missing part(s) to: PARTS, Box 1420,
Missoula, MT 59806 or call:
1-800-769-5693 or FAX [phone].

A
B
C
D
E
PARTS DIAGRAM
Left Side 01011641 1 ea.
Facia Strip 01011686 1 ea.
Back 01011652 1 ea. Top 01011601 1 ea.
Right Side 01011641 1 ea.
A
B
C
D
E
AB
C
D
E
AB
C
D
E
AB
C
D
E
H3 Rafix Bolt 909925 11 ea.
Attachment Tape 298530 2 ea.
H1 Rafix Cam 909909 4 ea.
HARDWARE
E
H6
H2 Rafix Flush
Cam 909834 7 ea.
H4

Insert four Rafix Camsv
H1) into the Top (C) and
Rafix Flush cams (H2)
into Back (D)
#1
Insert three Rafix Bolts (H3) into the Facia Strip (E)
Position the Rafix Bolts into the corresponding holes in the Top (C).
#2
C
D
H1
H2
H2
H1
E
C
H3
H3
H3
H1
H3
ASSEMBLE DISASSEMBLE
Using the Rafix System:
Insert the Rafix Cams into the
appropriate holes. The flat edge of
the cam should be facing the edge
of the panel.
Slide Rafix Cams of the panel to be
attached onto the corresponding posts.
Using a #3 Phillips screwdriver, turn the
rotating portion of the Rafix Cam a 1/2
turn clockwise to secure. IMPORTANT!
Do not exceed 1/2 turn when tightening
cams. Turn 1/2 turn counterclockwise
to disassemble and remove panel.
When screwing post
into hole, Do Not
over tighten. Screw
post down until
bottom face of post
flange just touches
board surface.
Flat
edges
must be
aligned
H2
H6

Screw four Rafix Bolts (H4) into the Left Side (A) and Right Side (B) where indicated.
#3
AB
H3 H3
#4 Place the Top (C) and Facia Strip (E)
on some packing material as shown.
Position the bolts Left Side (A) into
the Top (C) and turn cams clockwise
to secure.
Position the Right Side (B) onto
the unit and turn the cams (H1)
clockwise to secure.
#6
Position the Back (D) onto the
bolts of the Left Side (A) and
turn the cams (H1) clockwise
to secure.
#5
H3

Uncoil the Tape Strips (H4) and
affix one strip onto each of the
bottom edges of the Left Side (A)
and Right Side (B).
#7
Remove the backing from each Tape Strip
(H4) and carefully align rear and side
edges of the Riser and the unit to be
attached as shown. When aligned, place
the Riser on the desk unit.
Note: It will be difficult to remove or
reposition the units once joined.
#8
#9 Your Glacier Riser is now fully installed
to the Desk Unit and is ready for use.