Kohler PARALLEL 23492T-4 User manual

1333450-2A-A 1
1333450-2A-A 4
Ø28
240
250
G1/2˝
723~743
57
Ø35
Ø60
117
270
Ø20
10º
846~866
782~802
89
70 Min.
630 Max.
125×125
*221
G1/2˝
G1/2˝
G1/2˝
1500
PARALLEL
SERVICE PARTS
23492T-4 Floor Mount Bath Filler With Handshower 23492T-4 Floor Mount Bath Filler With Handshower
**Color code must be specified when ordering.
NOTE: For all Asia pacific regions (excluding China) add SP (SPxxxxxxx**) in front of the part number when ordering.
INSTALLATION INSTRUCTIONS
PARALLEL
BEFORE YOU BEGIN
All information is based on the latest product information available at the time of publication. Kohler Co. reserves
the right to make changes in product characteristics, packaging, or availability at any time without notice.
Please leave these instructions for the consumer. They contain important information.
NOTES:
1. Flush the water supply pipes thoroughly to remove debris.
2. Inspect the supply tubing for damage. Replace as necessary.
3. Observe local plumbing codes.
4. The minimum working pressure for the diverter is 0.05MPa(0.5bar).
5. Check for leaks before covering the pipes, repairs as needed.
6. The highest working pressure for handshower is 0.5MPa(5bar). If it exceeds 0.5MPa(5bar), a pressure reducer is
needed. The highest water and environment temperature is 60ºC. Please keep handshower and shower arm away
from heater, or it may become damaged and cause injury to the user.
7. Please purchase the matched mounting base 97905T when install the faucet.
ROUGH-IN DIMENSIONS
Special model meets or exceeds the following at date of manufacture: TIS
STANDARD APPLICABLE
*Please purchase the appropriate bathtub according to the dimension.
1333529**
1333434**
1333433
1333432
835016
835018
1358691
1333440**
1333437
835015
74463
77950
1229992
1358690**
77955
38618
1337774
1333439**
3013706
3008523
1333448
1258088
1177225
833438
3008523
1297467**
1030624
1240266
77420
77955
834404
32657
1082901
1010167
65218
3006148
880010
831727**
880010

1333450-2A-A 2
1333450-2A-A 3
5
4
7
8
1
6
2
3
10
11
13
12
9
HANDLE OPERATION
Lift the handle gently. Turn clockwise for hot water, counter-clockwise for cold water.
Pull the diverter for handshower. Push the diverter back in the normal position for bath spout.
Press the buttons of the handshower to change the water flow.
INSTALLATION
INSTALLATION CHECKOUT
How to Maintain the Handshower
Any debris or mineral build-up may cause
the flow stream distorted or reduce the flow
rate. To remove the debris or mineral
build-up, run water through the handshower,
firmly press or rub your finger back and forth
across the rubber nozzles.
How to Install the Faucet
Shut off water supply. Cut away the
extending part of the base protector(1) in
accordance with the tile surface. Remove
plug(2) from the base. Remove protector(3)
from the faucet.
Slide up escutcheon kit(4). Install the faucet.
NOTE: Keep the faucet vertical to base, to
avoid damaging the O-rings on the bottom.
Keep the spout pointing to tub. Fix the
faucet to the base with screws(5) and
washers(6) through flange(7). Tighten the
screws with hex wrench(8).
Slide down the escutcheon kit, make sure it
is against the finished floor.
Ensure that all coupling nuts are tight.
Ensure that the handle is in the off position.
Turn on the main water supply, and
check for leaks. Repair as needed.
Remove the aerator(15) by key(14).
Remove the handshower(10). Turn on
faucet handle. Run hot and cold water
through spout for about one minute to
remove any debris. Remove and clean the
screen washer. Check for leaks at
this time. Remove any debris. Shut off
the faucet. Reinstall the aerator and hand-
shower.
How to Install the Handshower
If needed, install the restrictor(9) into the
inlet of the handshower(10). Connect
hose(11) to diverter kit and handshower with
washers. Tighten all the connections.
Hang the handshower on the bracket(13) of
the faucet.
All Finishes: Clean the finish with mild soap and warm water. Wipe entire surface completely dry with clean soft
cloth. Many cleaners may contain chemicals, such as ammonia, chlorine, toilet cleaner etc, which could adversely
affect the finish and are not recommended for cleaning.
Do not use abrasive cleaners or solvents on Kohler faucets and fittings.
CLEANING INSTRUCTIONS
14
15
10