Lamp FD50-H User manual

1
Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation.
Please keep this manual at hand for future reference.
FD50-H SLIDING DOOR SYSTEM Installation Manual
(Surface Mount Roller, Standard Sliding) Part No.
FD50HMP
SPECIFICATIONS
●This product is a parts set for a sliding door system for indoor
use.
●
Easy door installation and adjustment.
Door height Max. 2400 mm 2401‑2700mm
Door width 774‑1500mm 800‑1500mm
Min. Door thickness 30 mm
Max. Door weight 50 kg / door
Adjustable height range ±4 mm
ABOUT THE PRODUCT
FOR YOUR SAFE WORK AND CORRECT INSTALLATION
WARNING:

If not followed, death or serious injury may result.
Caution:
If not followed, injury or damage may result. 
This (sliding door system) should be installed by a qualified person. If the system is not installed correctly, the door will not
operate smoothly, and may cause injury.
It is necessary to manufacture the frame with sufficient strength so that it endures the weight of the door and any impact
upon opening/closing the door. Only use designated screws and ensure that they are fastened firmly. A frame with poor
strength or loose screws might result in the door falling and causing injury.
Do not try to use this product for anything other than its original purpose. Do not use any part for applications outside of its
specification.
Do not disassemble nor modify any parts other than those described in this document.
Make sure to follow the designated dimensions, specifications, and horizontal/vertical angles. Make sure that the frame is
not warped, since it may affect the movement of the door.
If cutting any parts, make sure to remove any burrs before installation. Also check the upper track for any left-over burrs or
scraps and remove these.
This product is a part for architectural fittings. After installation, make sure to test the finished product thoroughly to ensure
that it is well-functioning and safe.
Make sure to check the screws for slack at regular intervals (one month from first usage, half a year and then one time
every year is recommended).
Prohibited
Warning
Caution Required
Meaning of symbols

2
COMPONENT PARTS
INSTALLATION DRAWING (EXAMPLE)
9
41
16
5
28
6
41
18《32》
64
3
5
9
30
Track hole pitch 300
Track mount hole I4.5
15
1710《24》
28
16
20 25
28
17
15
80
25 110
35
4
4
25
12
72
12
74.5×9.5 elongated hole4×I4.5
4×5.2×8.2 elongated hole
screw 3.8×40
Min:30
5
Door vertical adjustment range
1 14
3
2
2
Dimension in
《》 : When floor guide L⑥(Option) is used.
Door process dimension
When vertical frame is notused,
apply two-way soft closer.
No. ①②③④⑤
Name Upper Roller
Surface Mount End stopper Floor guide S Upper track Door guide track
Item No. FD50-WRM FD50-HTST FD50-BG18 FD50-TRM
FD30-HBRT1500SIL
Item
Accessory screw:
Pan head tapping screw
4×45･････････4 pcs
Accessory screw:
Bind head tapping screw
4×16･････････5 pcs
(various sizes) 1500mm
Hole pitch : 300 mm
Pitch end : 30 mm
Accessory screw:
Flat fillistar pan head tapping screw
3.8×40
Hole pitch : 250 mm
Pitch end : 30 mm
Recommended screw:
Countersunk head
tapping screw
4×20
Single sliding
2 pcs 2 pcs 1 pc 1 pc 1 pc
Double sliding
4 pcs 4 pcs 2 pcs 2 pcs 2 pcs
In line sliding
4 pcs 4 pcs 2 pcs 1 pc 2 pcs
OPTIONAL
PA R T S
No ⑥⑦
Name
Floor guide L Spanner
Item No. FD50-BG32 FD50-BG32
Item
Accessory screw:
Pan head tapping screw
4×16･･････････5 pcs

3
30
100
Cut side
I4.5(Track mount hole)
ASSEMBLY
PREPARATION AND INSTALLATION
1
1. Cutting and drilling holes on upper track
Cut to suitable length. For cutting and drilling holes, refer to the
illustration below.
When cutting, reinforce the track to prevent deformation at cut
section.
When length from cut end to installation hole is more than 100
mm, provide 4.5 mm dia. hole at 30 mm from cut end
2. Installing Bracket
❶Disassemble
Door (tailing edge)
32
screw 4×16
Floor guide
80
25
80
6
72
110 25
121225
screw 4×45
Opening Opening
Outside
Outside
Bracket
Holder
Surface mount roller
Remove
❷Fastening
Pay attention to setting the direction of the bracket.
The open part of the bracket should face in the outside direction.
Electric screwdriver may damage the
track due to excessive tightening force.
Manual driver is recommended.
Surface mountroller①
Upper track④
3. Installing door guide track
(1) Cut the track to the same length as the door width.
When cutting, reinforce the track to prevent deformation at the
cut section.
(2) Fasten the track with countersunk head tapping screws 4×16
(not provided)
Door bottom guide track ⑤
6. Mounting Floor Guide
3RVLWLRQÀRRUJXLGHMXVWEHORZWKHcenter of upper track.
3RVLWLRQWKHÀRRUJXLGHVRWKDWWKHÀRRUguide stays under the door when
it is opened or closed.
4. Inserting Parts into Upper Track
Assemble the parts in order from ❶to ❹with care of direction.
Fasten end stoppers temporarily to prevent the inserted parts from falling.
5. Installation of track
Remove any dirt or aluminum chips from the track.
End stopper②
End stopper②
Countersunk head
tapping screw
(Not provided)
1
4
2
3
(This describesinstallation of a single side sliding door.)
Tapping screw
3.8×40(provided)

4
SUGATSUNE KOGYO CO.,LTD
Tokyo, JAPAN
Phone: [phone] E-mail:[email protected]
SUGATSUNE KOGYO (UK) LTD
Reading, UK
Phone: [phone] E-mail:[email protected]
SUGATSUNE EUROPE GmbH
Dusseldorf, GERMANY
Phone: [phone] E-mail:[email protected]
SUGATSUNE SHANGHAI Co., LTD
Shanghai, CHINA
Phone: [phone] E-mail:[email protected]
Guangzhou, CHINA
Phone: [phone] E-mail:[email protected]
SUGATSUNE KOGYO INDIA PRIVATE LIMITED
Mumbai, INDIA
Phone: [phone] E-mail:[email protected]
SUGATSUNE AMERICA, INC
California, USA
Phone: [phone] E-mail:[email protected]
Chicago, USA
Phone: [phone] E-mail:[email protected].
SUGATSUNE CANADA, INC.
Phone: [phone] E-mail:[email protected]
2018.12 0595-5
HANGING THE DOOR AND ADJUSTMENT
2
2. Hanging (Top part)
Insert the upper roller into the bracket as shown in the drawing below.
1. Hanging (Bottom part)
Put a 10 mm support under the door.
While holding the door, insert the floor guide
into the groove under the door.
U
pper roller
Bracket
Support
Bottom guide S
Bracket
Lower Raise
M8 Hanger bolt
6- 14
widthacrossflat
Bracket
Roller
Holder
Stopper position adjust screw
35
5. Fixing end stopper
Fix the end stopper to the right position. Set the end stopper in place
as shown below. Then, fasten with the provided screw.
Fasten the opposite end stopper in a similar manner
3. Adjustment of Door Height
(1)Remove the 10 mm support under the door.
(2)Adjust the door so that it is parallel to the upper track with 6- 14 mm of
clearance between the door and floor.
4. Installation of holder
Insert the holder as shown below.
Confirm that the claw of the
shaft support holder catches
the opposite side of the
holder.
Ensure that hanger
bolt head is straight
as shown for proper
fastening of the
holder.
Trouble Check Point Solution
Abnormal noise during
operation
Check track rollers for existence of dust or aluminum
powder. Remove the track and pull out the roller. Then, clean the roller.
Check for loose screws retaining the upper track. Tighten the screw.
Heavy door operation &KHFNLIGRRUERWWRPFRQWDFWVWKHÀRRU
9HULI\WKDWWKHWUDFNIL[LQJ VFUHZVDUHQRWORRVHQHG7KHQ DGMXVW WKHGRRU
KHLJKWVXFKWKDWWKHFOHDUDQFHEHWZHHQWKHGRRUERWWRPDQGÀRRULVPP
Door does not move. Check the track retaining screws for looseness. Roller touches the screw.
Retighten screws to free the roller.
Door starts to move. Check if the upper track is set horizontally. Using a level gauge, reset upper track horizontally.
■HOW TO REMOVE DOOR
(1)Put a support under the door.
(2)Pull out the Holder.
(4)Remove the door from the Bottom guide.
(3)Pull out the Upper roller
from the Bracket.
Holder
Bracket
Upper roller
TROUBLESHOOTING
)LQDOYHUL¿FDWLRQ Verify that all screws are securely tightened, and verify that all screws have been used.
PERIODICAL INSPECTION
・Clean inside of track.
・&KHFNXSSHUDQGORZHUJDSVEHWZHHQWKHGRRUDQGIUDPH,IQHFHVVDU\DGMXVWWKHJDSV