LuxaFlex 2106/56 User manual

83 Installation and User manual:
Model
Installation and User’s manual PB - GB
Subject to technical changes
FaceFix installation to a window frame / wall [F1]
Do not damage the product when using a sharp knife to open
the packaging! Fitting screws: Use a size-2 screwdriver (PO-
ZIDRIVE) or use an electric screwdriver at it’s lowest torque.
5DLOUHPRYDO8VHDÀDWVFUHZGULYHURIPD[PPZLGH2QO\
use the original screws enclosed, to prevent malfunctioning
from using too thick screw heads!
B
C
A
A
B
X=5 cm
xx
max. 70 cm
xx
max. 70 cm
2 3 3 3 1 10 30 - 80 cm
3 4 4 4 1 14 481 - 115 cm
3 5 5 5 1 16 5116 - 150 cm
4 6 6 6 1 20 6151 - 185 cm
4 7 7 7 1 22 7186 - 220 cm
5 8 8 8 1 26 8221 - 230 cm
AB
C
Removal
5
Connection
3
Tensioning/slackening the steel wire
1
FaceFix installation
2
Fitting the lower covers
4
Installation sequence
4-A1 4-A2
4-B1 4-B2
Rail installation sequence on Clips
The built-in motor (24 V DC) with automatic end position
adjustment may only be connected to the 230V mains
using a stabilized 24 Volt DC Power Supply.
Only use Power Supplies and controls recommended
by the manufacturer of the Pleated Blind, to prevent
damage or malfunctioning caused by non-compatible
electric components! When connecting electric compo-
nents, the wiring diagram provided by the manufacturer of
the Power Supply must be observed.
Note: if necessary, before clicking the rail
into place, slacken the steel wire
Push ¿rmly to the rightleft to tensionslacken
the steel wire
Number of partsProduct width
21-03-2014
2106/56 [F1]

84 Installation and User manual:
Model
Installation and User’s manual PB - GB
Subject to technical changes
Installation TopFix / RecessFix [R1]
Do not damage the product when using a sharp knife to open
the packaging! Fitting screws: Use a size-2 screwdriver (PO-
ZIDRIVE) or use an electric screwdriver at it’s lowest torque.
5DLOUHPRYDO8VHDÀDWVFUHZGULYHURIPD[PPZLGH2QO\
use the original screws enclosed, to prevent malfunctioning
from using too thick screw heads!
A
B
X=5 cm
xx
max. 35 cm
xx
y
y
max. 70 cm
A
BC
Removal
ABC
1
Clip installation (bottom rail)
2
Clip installation (high rail)
3
Tensioning/slackening the steel wire
5
Connection
4
Installation sequence
4-A1 4-A2
4-B1 4-B2
Rail installation sequence on Clips
The built-in motor (24 V DC) with automatic end position
adjustment may only be connected to the 230V mains
using a stabilized 24 Volt DC Power Supply.
Only use Power Supplies and controls recommended
by the manufacturer of the Pleated Blind, to prevent
damage or malfunctioning caused by non-compatible
electric components! When connecting electric compo-
nents, the wiring diagram provided by the manufacturer of
the Power Supply must be observed.
Note: if necessary, before clicking the rail
into place, slacken the steel wire
Push ¿rmly to the rightleft to tensionslacken
the steel wire
2 3 1 50 - 80 cm
3 4 1 781 - 115 cm
3 5 1 8116 - 150 cm
4 6 1 10151 - 185 cm
4 7 1 11186 - 220 cm
5 8 1 13221 - 230 cm
Product width Number of parts
21-03-2014
2116/66 [R1]