Motorline professional LINCE 400 User manual

LINCE 400/600
User’s and Intaller’s manual
v1.0
REV. 09/2013

00. CONTENT
▷ INDEX STANDARDS TO FOLLOW ◁
01. SAFETY INSTRUCTIONS
00. CONTENT
▷ Index | page 01.A
01. SAFETY INSTRUCTIONS
▷ Standards to follow | page 01.B
02. PACKAGE
▷ Inside package | page 02.A
03. OPERATOR
▷ Functionality | page 02.B
▷ Manual release | page 03.B
▷ Technical Specifications | page 04.A
04. INSTALLATION
▷ Installation dimensions | page 04.B
▷ Installation steps | page 06.A
▷ Installation map | page 07.A
05. TROUBLESHOOTING
▷ Final consumers instructions | page 08.A
▷ Instructions for specialized installers | page 08.B
06. COMPONENTS TEST
▷ Capacitors connection scheme | page 09.A
07. MAINTENANCE
▷ Maintenance | page 09.B
ATTENTION:
▷ To ensure the safety of people, it is important that you read all the following
instructions.Incorrect installation or incorrect use of the product can cause physical
injury and material damage.
▷ Keep these instructions in a safe place for future reference.
▷ This product was designed and produced strictly for the use indicated in this
manual. Any other use, not expressly indicated here, could compromise the good
condition/operation of the product and/or be a source of danger.
▷ ELECTROCELOS SA is not responsible for the improper use of the product,
or other use than that for which it was designed.
▷ ELECTROCELOS SA is not responsible if safety standards were not taken
into account when installing the equipment, or for any deformation that may occur to
it.
▷ ELECTROCELOS SA is not responsible for the safety and proper operation
when using components not sold by them.
▷ Do not make any modifications to the operator components and / or their
accessories.
▷ Beore installation unplug the automatism from the source of power.
▷ The installer must inform the client how to handle the product in case of
emergency and provide this manual to user.
▷ Keep remote controls away from children, to prevent the automated
system from being activated involuntarily.
▷ The customer shall not, under any circumstances, attempt to repair or tune
the operator .Must call qualified technician only.
▷ Connect the automatism to a 230V plug with ground wire.
▷ Operator for outdoor and indoor use.
01.A 01.B

02. PACKAGE
▷ INSIDE PACKAGE FUNCTIONALITY ◁
03. OPERATOR
In the package you will find the following components:
▷ 02 Swing operators LINCE
▷ 01 Control Board
▷ 02 4Channel transmitters
▷ 02 Front supports
▷ 02 Rear supports
▷ 02 Capacitors 8µF
▷ 01 Photocells
▷ 01 User’s manual
▷ 02 Release keys
Front supports
The operator LINCE, is a product developed exclusively for the automatic opening of
swing gates.
Besides being pratical, safe and powerful, this product has a new function incorpo-
rated so that you can transform a motor to apply on right leaves to left leaves.
This allows greater flexibility in the use of each operator.
Motor disassembly and assembly process, in order to transform motor, must be done
as follows:
02.A 02.B
Release keys
Photocells
Motor
Rear supports
Transmitters
Capacitor 8µF
Control board
User manual
Middle part
Upper part
Lower part
01 - Loosen the screws that secure the
Lower Part to Middle Part
02 - Remove Lower Part

03 - Loosen the screws of the Middle Part 04 - Remove Middle Part
03. OPERATOR
▷ FUNCTIONALITY MANUAL RELEASE ◁
03. OPERATOR
03.A 03.B
05 - Rotate Upper Part 180° 06 - Assemble operator by tightening all
components with the screws
07 - Full transformed operator
01 - Remove the plastic cap from the rear
end
Information engraved on the unlock shaft
D=Unlock || B= Lock
02 - Insert Release key on the unlock
shaft.
03 - Rotate key 180 ° in the direction
indicated in the figure to unlock
04 - Operator unlocked.
Note: To lock operator so it can work
automatically, must do it by turning the
key anticlockwise.

LINCE specifications are as follow:
LINCE 400 || 600 dimensions are the following:
▷ Power Supply
▷ Power
▷ Current
▷ Operating temperatures
▷Thermal protection
▷Working frequence
▷ Noise level
▷ Force
▷ Max leaf lenght
▷ Course
▷ RPM
AC 230V 50/60Hz
180W
1,3A
-25°C to 75°C
120°C
25%
<50dB
2300N
3000mm
400mm
1400 RPM
AC 230V 50/60Hz
180W
1,3A
-25°C to 75°C
120°C
25%
▷ Protection class IP54 IP54
<50dB
2300N
4000mm
600mm
1400 RPM
LINCE400 LINCE600
A =
B =
?mm
A- 10mm
AB
The operator LINCE must be installed with a small inclination , to prevent water
infiltration through the extension arm.
For this, the front support must be fixed to the gate with a height lower than the height
of the rear support. See example below:
03. OPERATOR
▷ TECHNICAL SPECIFICATIONS
It is very important that these dimensions are respected! Only this way can be
assured the correct functioning and durability of the operators!
It is also very important to have a levelled ground/terrain!
VERTICAL INSTALATION DIMENSIONS ◁
04. INSTALATION
04.A 04.B
Dimension A - Vertical distance from the floor to the top of the rear support .
Dimension B - Vertical distance from the floor to the top of the front support.
- Set dimension A (this can be any size of your choice).
- After you set dimension A, subtract 10mm to find dimension B.
Example:
▷ If the height of the rear bracket (dimension A) is set at 600 mm, then the height of
the front bracket (dimension B) will be 590 mm (600mm-10mm).
A
AB
747mm || 947mm
159mm
104mm
175mm
1162mm || 1562mm