MRC RG-12-RM User manual
PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATION
MRC.VER.02-11.10
INSTRUCTION MANUAL FOR
RG-12/06/03-RM/RTM
HIGH TORQUE STIRRER
1
Ⅰ
ⅠⅠ
Ⅰ、
、、
、
OUTLINE
Ⅱ
ⅡⅡ
Ⅱ、
、、
、
SPECIFICATION
Model RG-03 / RM / RTM RG-06 / RM / RTM RG-12 / RM / RTM
Speed (rpm) 0-300 0-600 0-1,200
Max. Torque (kg-cm) 60 30 15
Motor DC 200W
Power AC 110 / 220V , 50 / 60 Hz, 5 / 3A
Chuck φ1~10 mm
Safety device Heat breaker, glass fuse
Coating Medicine-resisting
Size ( 240 x 125 x 250 mm
Weight 6.8 kg
Needle type tachometer
& torque meter
2
Ⅲ
ⅢⅢ
Ⅲ、
、、
、
ACCESSORIES
1. Stirring shaft (SUS#304): φ8 x (L) 500 mm……………1 pc
2. Propeller: No. 6……………1pc
3. Holder……………1pc
4. Stand base: 7.7 kg……………1pc
5. Pole: φ19 x (L) 800 mm, 1.8 kg……………1pc
6. RM type equipped with a needle tachometer.
7. RTM type equipped with a need tachometer & torque meter.
Ⅳ
ⅣⅣ
Ⅳ、
、、
、
OPERATION INTRODUCTION
1. Set speed adjuster to “OFF” and then put plug into the socket.
2. Turn on the power switch behind the controller.
3. Turn on the speed adjuster.
(* Only when the adjuster indicates “OFF”, you can take off the plug or turn off the
source during high-speed rotation.)
4. When the temperature of motor reaches 75℃, the built-in thermal circuit breaker will stop
the
rotation to prevent the motor from burning out and the re-performance is allowed to start
only when the temperature is less than 55℃(about 30 min.).
(* If the rotation stops again, please reduce the stirring burden.)
5. Attached auto current-restraining function under control system, excessive viscosity or
current adding.
6. After renewing the carbon brush, and unloaded low-speed rotation for 1~2 hours is
needed for motor protection.
7. The choosing of propellers & stirring vessels depend on the temper of the materials.
(* For example, consistency, viscosity, etc.)
8. Using more than 2 propellers depends on the torque of the machine.
3
Ⅴ
ⅤⅤ
Ⅴ、
、、
、
ATTENTION
1. Avoid using the same source with other electrical appliances.
2. The overload burden will exhaust and damage the gear.
Ⅵ
ⅥⅥ
Ⅵ、
、、
、
ASSEMBLING
1. Place pole onto the stand base, and lock the screw nut.
2. Insert the flat end of pole into the stirrer body, then lock the hatless screw tightly, and
fasten in the holder slot.
3. Set the machine body, and adjust the altitude to prepare the placement of stirring shaft.
4. Put propeller on the flat side of screw, then fix it on one end of haft.
5. Turn left to open the holder, get stirring shaft into the hole, then fasten it.
Ⅶ
ⅦⅦ
Ⅶ、
、、
、
INSPECTION
When the machine is out of order, please check up whether:
1. The carbon brush on the two sides of the motor are out of using or in bad contact.
(Take them out and renew while out of using)
2. The fuse burns out or not.
3. The speed adjuster works normally or not.
* If everything is O.K., please send it back to the agent for examination & maintenance.*
This manual suits for next models
5
Table of contents
Other MRC Laboratory Equipment manuals
