MSA 10207314 User manual

User Instructions
MSA Tool Tethers with Loops
Doc./Mat.: 10208504/01
Print Spec.: 10000005389 (H)
CR 800000039571

1000 Cranberry Woods Drive
Cranberry Township, PA 16066
USA
Phone 1-800-MSA-2222
Fax [phone]
For your local MSA contacts, please go to our website www.MSAsafety.com
©
MSA 2019. All rights reserved
MSA, MSA The Safety Company, and the MSA The Safety Company Logo are
Registered Trademarks of MSA Technology, LLC in the U.S. and/or Other Countries.
For all other trademarks see https://us.msasafety.com/Trademarks.

3MSA Tool Tethers with Loops
US
Safety Instructions
WARNING!
• DO NOT connect any tool weighing more than 5 Ibs (2.26 kg) to a person. Tools
weighing more than 5 Ibs (2.26 kg) must be connected to a suitable structure.
• DO NOT exceed the specified product load capacity rating. See product tables for
load ratings.
• Connect the carabiner on the end of the tether to a suitable attachment point.
• DO NOT tie knots in a tether.
• DO NOT hook the tether to itself.
• DO NOT connect carabiners to each other.
• Inspect the tether before each use in accordance with the inspection instructions.
• Always keep tools tethered at heights. Exchange tools over a secure area (e.g.,
inside a controlled container, over a platform, etc.) or connect the tool to a secondary
anchor before disconnecting from the original anchor point.
• DO NOT alter this equipment or intentionally misuse it.
• DO NOT use fall arrest or rescue equipment in environments with temperatures
greater than 113°F (45°C) or temperatures lower than -31°F (-35°C).
• DO NOT use tool tether products adjacent to moving machinery, electrical hazards, or
in the presence of excessive heat, open flame or molten metal.
• DO NOT use tool tether products as part of a personal fall arrest or restraint system.
• Any tool tether product that has been subjected to fall arrest forces must be
immediately inspected for damage prior to continued use.
• DO NOT make a modification to a connected tool or product that will result in a
deviation from the manufacturer’s recommendation or specification.
• DO NOT make tool attachments in a manner that would allow the tool tether product
to be unintentionally disconnected.
• DO NOT use a tool tether product if it will interfere with the safe working condition, or
operation, of any personal fall protection product or system.
• DO NOT use a tool tether product if it will interfere with the safe working condition, or
operation, of the connected tool or equipment.
• Ensure the tool tether is kept free from any and all obstructions including, but not
limited to, entanglement with other workers, yourself, and surrounding objects.
• DO NOT wrap tool tether components around rough or sharp edges.
• All connected tools and equipment, including connection points, must be compatible
for use with tool tether products, and properly maintained and inspected in
accordance with the manufacturer’s instructions.
• Ensure proper tool drop clearance. Tool drop clearance is defined as:
Tool Tether Maximum Length + Tool Length + 1 ft (0.3 m) Safety Factor.
• DO NOT modify a tool or primary anchoring location that could result in manufacturer
guideline deviation.
Failure to follow these warnings can result in serious personal injury or death.
!

4MSA Tool Tethers with Loops
US
WARNING!
• DO NOT attach tool tether products to straight-shafted or tapered tools, unless in
accordance with the Taping Instructions included in this manual.
• DO NOT connect multiple tool tethers together.
• DO NOT use tool tether products to hoist taglines or other objects or to statically suspend
tools and equipment.
• Always wear appropriate personal protective equipment when installing or using tool tether
products.
• If PPE is resold, it is essential that instructions for use, maintenance, and periodic
examination are provided in the language of destination.
• DO NOT use MSA tool tether products if under the influence of drugs or alcohol.
Failure to follow these warnings can result in serious personal injury or death.
Compliance
The product may comply with:
• ANSI-ISEA 121-2018
See product label for specific compliance notifications.
MSA Tool Tethers with Loops labeled with ANSI-ISEA 121-2018 have been tested in compliance
with the requirements of ANSI-ISEA 121-2018.
Use
1. Thread the tether loop through the attachment point of the tool. (Figure 1)
If there is no attachment point, see the Taping Instructions included in this manual.
2. Guide the opposite end of the tether including the D-ring or side release buckle through the
loop. (Figure 2)
3. Pull tight and adjust the slide lock to snugly secure the loop around the tool. (Figure 3)
4. Attach the D-ring on a Tool Tether Loop Tail to a suitable connector. If using a Tool Tether
Detachable Loop, connect the hook end of the side release buckle to the insertion end of
the buckle on a Tool Tether Carabiner Detachable Loop. (Figure 4)
Inspection
• Tool tether products must be thoroughly inspected by a competent1person before each use.
• Tool tether products with deformities, unusual wear or deterioration must be immediately
removed from service and replaced.
• Inspect all material, stitching, hardware, D-rings, carabiners, side release buckles and other
connectors for damage or wear that may affect proper use of the tool tether.
• Ensure carabiners, side release buckles and other connectors operate properly.
• If a tool is dropped, inspect the tool tether and connector for damage. Any damaged tool
tether must be immediately removed from service and replaced.
• If a tool tether product has been taped to a tool using the Taping Instructions included in this
manual, the tape must be thoroughly inspected by a competent1person before each use.
Tape showing signs of wear or deterioration must immediately be removed and replaced.
1 Competent person: A person, other than the User, competent in the examination of PPE in accordance
with MSA instructions.
!

5MSA Tool Tethers with Loops
US
Fig. 1 Fig. 2
Fig. 3 Fig. 4