NUUO 6000S SERIES User manual

The Intelligent Surveillance Solution
Hardware & Software NDVR
Installation Guide
Ver. 5.1

Intelligent Surveillance Solution
Table of Contents
page - 1
T
TA AB BL LE E O OF F C CO ON NT TE EN NT TS S
TABLE OF CONTENTS......................................................................................................1
6000S/7000S SERIES ........................................................................................................2
Product Specification...............................................................................................2
System Requirement .................................................................................................2
Hardware Installation................................................................................................4
Maximum I/O Cards support for 6000S/7000S...................................................6
7100 SERIES.......................................................................................................................7
Product Specification...............................................................................................7
System Requirement .................................................................................................7
Hardware Installation................................................................................................8
8000HD SERIES ...............................................................................................................10
Product Specification.............................................................................................10
System Requirement ...............................................................................................10
Hardware Installation..............................................................................................11
DRIVER INSTALLATION..................................................................................................13
SOFTWARE INSTALLATION...........................................................................................15
SOFTWARE INSTALLATION –EXPRESS MODE..........................................................21
SOFTWARE INSTALLATION –FAILOVER AGENT (STANDARD MODE) ...............24
SOFTWARE INSTALLATION –FAILOVER AGENT (EXPRESS MODE).....................29
APPENDIX - MINIMUM HARDWARE REQUIREMENT ..............................................33

Intelligent Surveillance Solution
page - 2
6
60 00 00 0S S/ /7 70 00 00 0S S S SE ER RI IE ES S
Product Specification
Model
6016S
6008S
6004S
Display Rate
480fps(NTSC);
400fps (PAL)
240fps(NTSC);
200fps (PAL)
120fps(NTSC);
100fps (PAL)
Recording Rate
(CIF)
480fps(NTSC);
400fps (PAL)
240fps(NTSC);
200fps (PAL)
120fps(NTSC);
100fps (PAL)
Maximum Card
4
4
4
Video Input
16
8
4
Audio Input
16
8
4
Video Resolution
NTSC: 176x120; 352x240; 704x480
PAL: 176x144; 352x288; 704x576
Compression Format
Hardware Compression H.264
7016S
7008S
7004S
Display Rate
480fps(NTSC);
400fps (PAL)
240fps(NTSC);
200fps (PAL)
120fps(NTSC);
100fps (PAL)
Recording Rate (D1)
480fps(NTSC);
400fps (PAL)
240fps(NTSC);
200fps (PAL)
120fps(NTSC);
100fps (PAL)
Maximum Card
4
4
4
Video Input
16
8
4
Audio Input
16
8
4
Video Resolution
NTSC: 176x120; 352x240; 704x480
PAL: 176x144; 352x288; 704x576
Compression Format
Hardware Compression H.264
System Requirement
The system requirement depends on the number of camera connections
and the total bit rate of the IP cameras. Please refer Appendix - Minimum
Hardware Requirement or check NUUO Calculator on
http://support.nuuo.com/calculator/

Intelligent Surveillance Solution
Hardware Installation
page - 3
Caution
The electronic components within the unit are sensitive to
damage from Electro-Static Discharge (ESD). Please take
precautions at all times when handling the unit or its
sub-assemblies.
Proper Surge solution is needed for outdoor application. It
provides protection from damaging transient voltage surges and
spikes.

Intelligent Surveillance Solution
page - 4
Hardware Installation
Step1: Insert the card onto an empty PCI-e slot. Connect the Audio/Video
Cable to the connector.
Note 1: The audio input connectors are with red wires and marked of “A”
on them (such as “A1/9”); the video input connectors are with black wires
and marked of “V” (such as “V8/16”).
Note 2: You need to power down the PC before you insert the card.
Step 2: Connect the Watchdog wire to the reset connector on the main
board.
Note: With the Watchdog Wire connected, the system will be restarted if
any abnormal conditions.
Step 3: Turn on your PC and start Windows.
Step 3: Insert the included Software CD into CD-ROM.
Step 4: Refer the section Driver Installation on page 18 to install driver.
Step 5: After driver is installed, restart your PC.
Optional I/O Card: refer to the figures on the following pages.
Step 1: Fix the IO card onto your PC.
Step 2: Connect the Capture Card and the I/O Card with an included
ribbon cable (2.00mm IDC cable).
Note 1: The default configuration of blue slide switch on I/O Card as
below.
Note 2: If you only use one I/O card to connect with one of 6000S/7000S
cards, please make sure the configuration of the black slide switch as
below.
Maximum optional I/O Card support:
6000S/7000S can support maximum 4 I/O cards. Please refer to figures on
the following pages.

Intelligent Surveillance Solution
page - 5
6000S/7000S Series Capture Card
I/O card
Note: Please do not connect 2 capture cards in one IO board at the same
time.
Connect to IO board
(2.00mm IDC cable)

Intelligent Surveillance Solution
page - 6
Maximum I/O Cards support for 6000S/7000S
Note: If you use more than one IO card, please make sure the
configuration of each black switch as above.

Intelligent Surveillance Solution
page -7
7
71 10 00 0 S SE ER RI IE ES S
Product Specification
7116
7108
Display Rate
480fps(NTSC);
400fps (PAL)
240fps(NTSC);
200fps (PAL)
Recording Rate (D1)
480fps(NTSC);
400fps (PAL)
240fps(NTSC);
200fps (PAL)
Maximum Card
1
1
Video Input
16
8
Audio Input
16
8
Video Resolution
NTSC: 176x120; 352x240; 704x480
PAL: 176x144; 352x288; 704x576
TV Output Rate
w/ HDMI: RCA & HDMI: 10fps
w/o HDMI: RCA: 25fps
Only HDMI: HDMI: 14fps
Compression Format
Hardware Compression H.264
System Requirement
The system requirement is depend on the number of camera connections
and the total bit rate of the IP cameras. Please refer Appendix - Minimum
Hardware Requirement or check NUUO Calculator on
http://support.nuuo.com/calculator/
Caution
The electronic components within the unit are sensitive to
damage from Electro-Static Discharge (ESD). Please take
precautions at all times when handling the unit or its
sub-assemblies.
Proper Surge solution is needed for outdoor application. It
provides protection from damaging transient voltage surges and
spikes.

Intelligent Surveillance Solution
page - 8
Hardware Installation
Step1: Insert the card onto an empty PCI-e slot. Connect the Audio/Video
Cable to the connector.
Note 1: The audio input connectors are with red wires and marked of “A”
on them (such as “A1/9”); the video input connectors are with black wires
and marked of “V” (such as “V8/16”).
Note 2: You need to power down the PC before you insert the card.
Step 2: Connect the Watchdog wire to the reset connector on the main
board.
Note: With the Watchdog Wire connected, the system will be restarted if
any abnormal conditions.
Step 3: Turn on your PC and start Windows.
Step 3: Insert the included Software CD into CD-ROM.
Step 4: Refer the section Driver Installation on page 18 to install driver.
Step 5: After driver is installed, restart your PC.
Optional I/O Card: refer to the figures on the following pages.
Step 1: Fix the IO card onto your PC.
Step 2: Connect the Capture Card and the I/O Card with an included
ribbon cable (2.54mm IDC cable).
Note 1: The default configuration of blue slide switch on I/O Card as
below.
Note 2: Before install SCB-7100 Series cards, please connect HDMI cable
first then it would be easier to fix the card onto the PCI -e slot.
Note 3: Some chassis may not be suitable for installing SCB-7100 series due
to the original design, please check the dimension of the chassis before
installing.

Intelligent Surveillance Solution
page - 9
7100 Series Capture Card
I/O card
Maximum I/O Cards support for 7116
Please refer to page 5 Maximum I/O Cards support for G3-3016

Intelligent Surveillance Solution
page - 10
8
80 00 00 0H HD D S SE ER RI IE ES S
Product Specification
8004HD
Display Rate
120fps(NTSC);
100fps(PAL)
Recording Rate
1080P@120(NTSC)
1080P@100(PAL)
Maximum Card
4
Video Input
4
Audio Input
0
Video Resolution
1080P30/25
720P60/50/30/25
Compression Format
Hardware Compression H.264
System Requirement
The system requirement is depend on the number of camera connections
and the total bit rate of the IP cameras. Please refer Appendix - Minimum
Hardware Requirement or check NUUO Calculator on
http://support.nuuo.com/calculator/
Caution
The electronic components within the unit are sensitive to
damage from Electro-Static Discharge (ESD). Please take
precautions at all times when handling the unit or its
sub-assemblies.
Proper Surge solution is needed for outdoor application. It
provides protection from damaging transient voltage surges and
spikes.

Intelligent Surveillance Solution
page -11
Hardware Installation
Step1: Insert the card onto an empty PCI-e slot. Connect the BNC Cable
(not in product content) to the connector.
Note: You need to power down the PC before you insert the card.
Step 2: Connect the Watchdog wire to the reset connector on the main
board.
Note: With the Watchdog Wire connected, the system will be restarted if
any abnormal conditions.
Step 3: Turn on your PC and start Windows.
Step 3: Insert the included Software CD into CD-ROM.
Step 4: Refer the section Driver Installation on page 18 to install driver.
Step 5: After driver is installed, restart your PC.
Optional I/O Card: refer to the figures on the following pages.
Step 1: Fix the IO card onto your PC.
Step 2: Connect the Capture Card and the I/O Card with an included
ribbon cable (2.00mm IDC cable).
Note 1: The default configuration of blue slide switch on I/O Card as
below.
Note 2: If you only use one I/O card to connect with an 8004HD card,
please make sure the configuration of the black slide switch as below.
Maximum optional I/O Card support:
Please refer to page 11 Maximum I/O Cards support for 6000S/7000S

Intelligent Surveillance Solution
page - 12
8004HD Card
Note: The default configuration of the black switch on 8004HD card is as
above. Do not adjust it.
I/O card

Intelligent Surveillance Solution
page - 13
D
DR RI IV VE ER R I IN NS ST TA AL LL LA AT TI IO ON N
Step 1: Insert the Installation CD. Run autostartup.exe from the
CD-ROM directly to start the installation.
Step 2: Select “DVR Driver Installation” then click on it.
Step 3: In the NUUODriver Setup Wizard dialog box, click Next to
continuous.
Step 4: Check the “License agreement”. Click “I Agree” to continuous.

Intelligent Surveillance Solution
page - 14
Step 5: Installing NUUODriver.
Step 6: Click “Finish”after installing the system completely, and then
choose to reboot now or later.

Intelligent Surveillance Solution
page -15
S
SO OF FT TW WA AR RE E I IN NS ST TA AL LL LA AT TI IO ON N
Step 1: Insert the Installation CD. Run Autorun Tool from the CD-ROM
directly to start the installation.
Step 2: Select “Server Application Installation” then click on it.
Step 3: In the InstallShield Wizard dialog box, select language and click
Next to continuous.
Step 4: There are 2 Installation Mode of options in “Initiation Mode”
window, select one and click Next to start the installshield of Server
package.

Intelligent Surveillance Solution
page - 16
Step 3: There are 4 system types of options in “System Setup Tool” window,
select one and click Next to start the installshield of Server
package.
-NUUO IP Surveillance System/Trial System
-NUUO MPEG-4 Hybrid System
-NUUO Full HD/D1 H.264 Hybrid System
Not e: The Setup Tool will detect the type of capture cards installs
on PC and enable the options of system types automatically.

Intelligent Surveillance Solution
page - 17
Step 4: In the InstallShield Wizard dialog box, click Next to continuous.
Step 5: Check the option “I accept the terms of the license agreement”.
Click Next to continuous.
Step 6: Please enter your name and the company name for which you
work. Click Next to continuous.

Intelligent Surveillance Solution
page - 18
Step 7: Select “Complete Setup Type” or “Custom Setup Type” to install the
System.
COMPLETE SETUP TYPE
Install all program features into the default directory.
-Check the option “Complete”, and then click “Next”. All
program features will be installed. [Require the most disk
space.]
CUSTOM SETUP TYPE
Install the system to a preferred directory. Or select whichever
program feature(s) to install. This is recommended for advanced
users.
-Check the option “Custom”, and then click “Next”.
-Select appointed folder where setup will install files to. Click
“Change” to modify the installation directory.

Intelligent Surveillance Solution
page - 19
-Select the features setup will install. There are 4 features to
choose in the server setup process: MainConsole, Playback,
LiveView, Backup, and Verification tool. Click “Next” after
confirmation.
Step 8: Click install to start the installation.
Step 9: Click Finish after installing the system completely.