PR Lighting PR5000 User manual

PR5000 Wash Beam
This product manual contains important information about the safe installation and use of this
projector. Please read and follow these instructions carefully and keep this manual in a safe place
for future reference.
PR LIGHTING LTD.
http://www.pr-lighting.com

2/21
INDEX
SAFE USAGE OF THE PROJECTOR 3
INSTALLING THE PROJECTOR 4
FITTING THE LAMP 4
POWER SUPPLY – MAINS 5
CONTROL CONNECTIONS 5
DMX TERMINATOR 6
SETUP OPTIONS-PROJECTOR CONFIGURATION 6
TO SET THE DMX START ADDRESS 6
OPERATION MENU 8
ERROR MESSAGES 11
REPLACING GOBOS 11
DMX PROTOCOL 12
LED INDICATION 14
MAINTENANCE 14
LUBRICATION 14
KEEPING THE PROJECTOR CLEAN 14
TROUBLESHOOTING 15
TECHNICAL DATA 16
ELECTRICAL DIAGRAM 19
COMPONENT ORDER CODES 20
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change without
notice. Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of
product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any consequence
arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in good
condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not use the
unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.
ACCESSORIES
These items are packed together with the projector:
Name Quantity Unit Remark
G clamps 2 Pcs
XLR cable 1 Pc 5-pin plug
Safety cord 2 Pcs
Spare gobos 4 Pcs
This manual 1 Pc
Ωclamps 2 Pcs Options

When unp
a
Should the
r
The projec
t
excessive
h
The projec
t
The projec
t
The projec
t
that no ven
t
Do not proj
e
A
void direc
t
Do not atte
m
Electrical c
o
Before inst
a
It is essenti
a
Do not con
n
Make sure
with other c
a
Keep the l
a
The projec
t
attached a
s
The lamp
u
cooled, thi
s
lamp and t
h
Never run t
The lamp s
Shields an
d
impaired, f
o
Exterior su
r
There is n
o
covers rem
If you have
Always
d
before a
t
a
cking and be
f
r
e be any da
m
t
or is for ind
o
h
eat, humidity
t
or is not desi
g
t
or is only inte
n
t
or must be in
s
t
ilation slots a
r
e
ct the beam
t
exposure to
t
m
pt to disma
n
o
nnection mu
s
a
llation, ensu
re
a
l that each p
r
n
ect this devi
c
that the pow
e
a
bles. Only ha
n
a
mp clean. D
o
t
or should al
w
s
shown in “in
s
u
sed in this pr
o
s
will require a
h
e projector.
B
he projector
w
hall be chang
d
lens shall b
e
o
r example b
y
r
face tempera
o
user service
a
oved.
any question
s
d
isconnec
t
t
tempting
a
SAF
E
f
ore disposin
g
m
age caused
b
o
or use only,
I
and dust. Do
g
ned or inten
d
n
ded for insta
l
s
talled in a lo
c
r
e blocked.
onto inflamm
a
t
he light from
n
tle and/or m
o
s
t only be car
r
re
that the volt
a
r
ojector is cor
r
c
e to any othe
e
r-cord is nev
e
n
dle the powe
r
o
not touch th
e
w
ays be insta
l
s
talling the pr
o
o
jector is a di
s
pprox 15 min
u
B
ut occasional
w
ithout a lamp
ed if it has be
c
e
changed if
y
cracks or de
e
tures of the lu
a
ble parts insi
d
s
, don’t hesita
t
from the
a
ny maint
e
E
USAG
E
g
of the carto
n
b
y transportat
I
P20. Use o
n
not allow co
n
d
ed to be mou
l
lation, operat
i
c
ation with ad
e
a
ble surfaces,
the lamp. Th
e
o
dify the proje
c
r
ied out by qu
a
a
ge and freq
u
r
ectly earthed
r types of dim
e
r crimped or
r
-cord by the
p
e
lamp glass
w
l
led with a se
c
o
jector” sectio
n
s
charge lamp.
u
tes. Switchi
n
breaks will p
r
.
c
ome damag
e
they have b
e
e
p scratches.
minaire after
5
d
e the projec
t
te to consult
y
mains, w
h
e
nance wo
3/21
E
OF TH
E
n
check if ther
e
ion, consult y
o
n
ly in dry loc
a
n
tact with wat
e
nted directly
o
i
on and maint
e
e
quate ventila
t
minimum di
s
e
light is harm
f
c
tor in any wa
y
a
lified person
n
u
ency of pow
e
and that elec
t
mer apparatu
damaged by
p
lug. Never p
u
w
ith bare han
d
c
ondary safe
t
n
.
After switchi
n
n
g the lamp o
n
r
olong the life
o
e
d or thermall
y
e
come visibly
5
minutes op
e
t
or, do not op
e
y
our dealer or
h
en the d
e
rk !
E
PROJ
E
e
is no transp
o
o
ur dealer an
d
a
tions. Keep t
h
e
r or any othe
r
o
n to inflamm
a
e
nance by qu
t
ion, at least
5
s
tance is 5m.
f
ul to the eye.
y
.
n
el.
e
r supply mat
c
t
rical installati
o
s.
sharp edges
u
ll out the plu
g
d
.
t
y fixing. A sa
n
g off d
o
n’t att
e
n
and off at s
h
o
f the lamp a
n
y
deformed o
r
damaged to
s
e
ration is 80℃
e
n the housin
g
manufacture
r
e
vice is no
t
E
CTO
R
o
rtation dama
g
d
do not use t
h
h
is device a
w
r
liquids.
a
ble surfaces.
alified person
n
5
0cm from adj
5m
c
h the power r
e
o
n conforms t
o
. Never let th
e
g
by tugging t
h
fety cord is s
u
e
mpt to resta
r
h
ort intervals
w
n
d projector.
r
reached its li
s
uch an exte
n
, when stead
y
g
and never
o
r
.
t
in use o
r
g
e before usi
n
h
e apparatus.
w
ay from rain
n
el.
acent wall su
r
e
quirements
o
o
all relevant
s
e
power-cord c
o
h
e power-cor
d
u
pplied for th
i
r
t the projecto
r
w
ill reduce the
fe limi
t
.
n
t than their
e
y
state is achi
e
o
perate the pr
o
r
before cl
e
n
g the project
o
and moistur
e
r
faces. Be su
r
o
f the project
o
s
tandards.
o
me into conta
c
d
.
i
s; it should b
r
until lamp h
a
life of both th
e
ffectiveness
i
e
ved 170℃,
o
jector with th
e
aning it
o
o
r.
e
,
r
e
o
r.
c
t
e
a
s
e
i
s
e
o
r

4/21
INSTALL THE PROJECTOR
Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers
attached to each clamp. Hang the fixture on the structure and fasten the screws attached to each clamp. (See the
WARNING on the underside of the base as shown above) To pass 2 SAFETY CORDS through 4 HOLES for safety!
Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning. Always ensure that
the structure that you are going to mount the projector is secure and is strong enough to support the weight of PR5000
FS(PR3000 FS)
WARNING
1. Unlock the PAN and TILT before the 1st application of projector for safety.
2. The projector MUST be lifted or carried by the HANDLES instead of clamps.
3. For safety the safety cord should support 10 times of the unit’s weight.
FITTING THE LAMP
Unplug the projector from power before lamp installation or replacement and wait for it to cool.
Lock the yoke before fitting/replacing the lamp.
Loosen 4 fast-fit screws and remove the back cover, you can see the structure as shown in the figure above.
Rotate the lampholder to the left and take out the worn-out lamp.
Fit new lamp and close the back cover by fastening 4 fast-fit screws. Note: don’t touch the bulb of the new lamp with
bare hand so as not to influence the beam output;
WARNING: The MSR series are high-pressure lamps with external igniters ( ). Care should always be taken
when handling these lamps.Always read the manufacturers "Instructions for use" enclosed with the lamp.
106
256
HANDLE
SAFETY CORD CLAMP
To pass 2 SAFETY CORDS
through 4 HOLES for safety!
WARNING
CONTROL PANEL
CLAMP
FAST-FIT SCREWS
LAMP REAR COVER

5/21
POWER SUPPLY-MAINS
Connect the power cord as follows:
L (live) =brown
E (earth) =yellow/green
N (neutral) =blue
Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked
on the panel of the projector. It is recommended that each projector be supplied separately so that they may be
individually switched on and off.
IMPORTANT
It is essential that each projector is correctly earthed(yellow/green twin wire) and the electrical installation
conforms to all relevant standards.
CONTROL CONNECTION
Connection between controller and projector and between one projector and another must be made with a 2
core-screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via
cannon 3 pin (which are included with the projector) or 5 pin XLR plugs and sockets. The XLR's are connected as shown
in the figure above.
Note: care should be taken to ensure that none of the pins touch the metallic body of the plug or each other. The body of
the plug is not connected in any way other than as shown above. The projector accepts digital control signals in protocol
DMX512 (1990).
Connect the controller’s output to the first fixture’s input, and connect the first fixture’s output to the second fixture’s input
and connect the rest fixtures in the same way. Eventually connect the last fixture’s output to a DMX terminator as shown
in the figure below.
DMX IN DMX OUT DMX IN DMX OUT DMX IN DMX OUT
TO TERMINATER
TO CONTROLLER

6/21
DMX TERMINATOR
In the Controller mode, at the last fixture in the chain, the DMX output has to be connected with a DMX terminator. This
prevents electrical noise from disturbing and corrupting the DMX control signals.
The DMX terminator is simply an XLR connector with a 120Ω(ohm) resistor connected across pins 2 and 3, which is
then plugged into the output socket on the last projector in the chain. The connections are illustrated below.
SETUP OPTIONS-PROJECTOR CONFIGURATION
Projector configuration can be set conveniently via switch button and LCD display. Turn the projector on and the LCD
display will show DMX address you set and save last time and it can be reset and saved again as you please.
Launch the projector. Press button ENTER more than 5 seconds to unlock panel. After this, the display shows the
projector’s function menu and each option has its own sub-menus. Each menu stands for special function, see details as
follows.
Press button UP or DOWN if you want to browse through the various Setup Options. There are 10 option codes
from DMX Address to Wireless options, and each code has a specific function. If you turn the encoder
knob clockwise, the function like as button UP . On the contrary, the function like as button DOWN .
Press button ENTER to save your settings or enter the next menu. There is same function if you push the encoder knob.
Press button UP or DOWN to shift.
Press button FUNC, it will return to the upper menu one by one. If you stay for minutes defaulted will show display status
automatically.
TO SET THE DMX START ADDRESS
Each projector must be given a DMX start address so that the correct projector responds to the correct control signals.
This DMX start address is the channel number from which the projector starts to “listen” to the digital control information
being sent out from the controller. PR5000 Wash Beam has 3 DMX modes. There are standard mode, extended mode
and short mode. For example standard mode have 17 channels, so set the No. 1 projector’s address 001, No. 2
projector’s address 018, No. 3 projector’s address 035, No. 4 projector’s address 052, and so on.
Launch the projector. Press button ENTER or encoder knob more than 5 seconds to unlock panel.
21
3
120
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain.
PIN 3
PIN 2
UP
UP

7/21
Press button FUNC to display DMX address;
Press button UP and DOWN, you can set the address;
Press button ENTER to confirm; In the same time. The GREEN LED will flash one time. It means the setting has
been enabled.
Press button FUNC, it will return to the upper menu one by one.

8/21
OPERATION MENU
1st LEVEL 2nd LEVEL 3rd LEVEL 4th LEVEL
PR LIGHTING
PR5000 Wash Beam
DMX Address=XXX
DMX Address
DMX Address
Short Mode
Standard Mode
Extended Mode
Reset Rese
t
A
re You Sure?
Config Settings
DMX Mode
DMX Mode
Standard
DMX Mode
Extended
DMX Mode
Short
Lamp Control
Lamp Control B
y
Control Channel
Lamp
C
ontrol B
y
Power
Lamp
C
ontrol B
y
DMX Si
g
nal
Loss of DMX
When DMX is Los
t
Normal time ou
t
When DMX is Los
t
Hold Last Value
Fan Speed
Quiet
Standard
High Speed
Factory Settings
(Press button
DOWN/UP/ENTER at the
same time to enter the
sub-menu)
Fixture type
(WARNING：Never
change the fixture type
or the systemwill be
damaged!)
Option Settings
Colour Rotations
Colour Rotations
STEPPED
Colour Positions
LINEAR
Pan DMX Invert
Pan DMX Invert
OFF
Pan DMX Invert
ON
Tilt DMX Invert
Tilt DMX Invert
OFF
Tilt DMX Invert
ON
Pan Tilt Swap
Pan Tilt Swap
OFF
Pan Tilt Swap
ON
Dimmer Invert
Dimmer Invert
OFF
Dimmer Invert
ON
Zoom Invert
Zoom Invert
OFF
Zoom Invert
ON
CMY Invert CMY Invert
OFF

9/21
CMY Invert
ON
CTO Invert
CTO Invert
OFF
CTO Invert
ON
Defaults
Defaults
OFF
Defaults
Restore Defaults
Display Options
Display Mode
Display
On Always
Display
Off After Delay
Display Dimming
Disp Dim Level
Min
Disp Dim Level
1
Disp Dim Level
2
Disp Dim Level
3
Disp Dim Level
4
Disp Dim Level
5
Disp Dim Level
6
Disp Dim Level
7
Disp Dim Level
8
Disp Dim Level
9
Disp Dim Level
Full
Display Contrast Display Contrast
XXX(1~36, Default is 16)
Display Language
Language =
English
Language =
Chinese
Information
Lamp Hours Lamp Hours =
XX Reset Lamp Hours Are You Sure?
Total Hours Total Hours =
XX
Temperature
Display Board Display Board =
XX℃
Driver Board 1 Driver Board 1 =
XX ℃
Driver Board 2 Driver Board 2 =
XX ℃
Pan and Tilt Pan and Tilt =
XX ℃
Head Sensor Head Sensor=
XX ℃
Software Version
Display Board Display Board =
X.X.X
Driver Board 1 Driver Board 1 =
X.X.X
Driver Board 2 Driver Board 2 =
X.X.X

10/21
Pan and Tilt Pan and Tilt =
X.X.X
Power Board Power Board =
X.X.X
View DMX values DMX Channel
1=XXX
Electronic SN Electronic SN=
************
RDM Device Label
RDM Device Label
ANSI E1.20 RDM
Version
Test M o d e s
Factory Setup
Factory Setup
OFF
Factory Setup
ON
Self Test
Self Test
OFF
self test
ON
Lamp Manual
Control
Lamp Status S = X C=X
Turn Lamp On
Turn Lamp Off
Wireless Options
Wireless Mode
Wireless Mode
Wireless First
Wireless Mode
XLRFirst
Wireless Mode
Wireless Only
Wireless Mode
XLROnly
Wireless Mode
Wireless To XLR
Un Link Wireless Really Un Link
Enter=Yes