PR Lighting XR 380 BWS User manual

1
XR 380 BWS
PR-2393A
The user manual contains important information about the safe installation and use of a projector. Please read and
followtheseinstructions carefullyand keepthemanualina safeplacefor futurereference.
PR LIGHTING LTD.
http://www.pr-lighting.com

2
INDEX
1.
SAFETYANDWARNINGS ………………………………………………………………………………………
3
2.
INSTRUCTIONS……………………………………………………………………………………………………
4
3.
APPEARANCE………………………………………………………………………………………………………
5
4.
INSTALLATION……………………………………………………………………………………………………
5
5.
SETUPANDCONFIGURATION……………………………………………………………………………………
10
6.
OPERATIONMENU ………………………………………………………………………………………………
11
7.
DMXPROTOCOL…………………………………………………………………………………………………
13
8.
ERROR MESSAGE………………………………………………………………………………………………
17
9.
TECHNICALDATA…………………………………………………………………………………………………
17
10
CIRCUITDIAGRAM ………………………………………………………………………………………………
20
11.
COMPONENTORDERCODES……………………………………………………………………………………
21
APPENDIX…………………………………………………………………………………………………………
22
ACCESSORIES
The following items aresupplied with theprojector andplease check:
Name
Quantity
Unit
Remark
Safetycord
1
Pc
Clamp
2
Pc
Foldableclamp
2
Pc
Optional
User manual
1
Pc
Please note that as part of our ongoing commitment to continuous product development, specifications are subject to change
without notice. Whilst every care is taken in the preparation of the manual we reserve the right to change specifications in the
course of product improvement. The publishers cannot be held responsible for the accuracy of the information herein, or any
consequence arising from them.
Every unit is tested completely and packed properly by the manufacturer. Please make sure the packing and / or the unit are in
good condition before installation and use. Should there be any damage caused by transportation, consult your dealer and do not
use the unit. Any damage caused by improper use will not be assumed by the manufacturer and / or dealer.
Any future technical change in the user manual won’t be with any notice.
Note: For the products made by Guangzhou PR lighting Ltd, the warranty for the whole product is one year starting from the
delivery date but the light source is not within the warranty

3
1. SAFETYANDWARNINGS
NOTE
Before a projector’s installation, power-on, operation and maintenance, please carefully read
thesafety informationhereinafter!
Thefollowingsafetysignsareusedintheusermanual.
Warning
User
Manual
Electrical
shock
Goggles
Protective
Gloves
Flames
High
Temperature
● When unpacking , check if there is transportation damage before using the projector. Should there be any damage
caused by transportation,consultyour dealer anddonotuseit.
●The manufacture is not responsible for loss caused by the user not following the manual or changing the projector as
he/shelikes
●Please be notedthatthedamage causedbychangingtheprojector at will is notwarranted.
● Do not hesitate to contact thedealeror the manufacturer if anyquestions or advice.
●Ifa lampisdamagedordeformsbecause of heat,itshould bereplaced.
● Theprojectorisforindoor useonly,IP20.
● Use only in dry locations. Keep this unit away from rain and moisture, excessive heat, humidity and dust. Do not allow
contact with wateroranyother liquids.
●The projector should be kept away from high temperature, fire, electrical surge, vibration and strong light while being
operated
●The projector is only intended for installation, operation and maintenance byqualified personnel. And the operation
muststrictlyfollowtheproceduresinthemanual
●Norepairableparts intheprojectoranddonot opencovers formaintenance byyourself.
●Don’t look straightly into the light sources especially for epileptics, otherwise eyes will be burned.
●Donotconnecta projectortoanytypeofdimmerpack.
●Ifthelamp,lensandscreenprotective coveroftheaprojectorhaveobviousdamage,i.e.,totheextentthatithurtsthe
performancelikecrackingordeformation. Please stopusing itandreplace themwiththeoriginalparts,otherwise its
performancewillbe compromised.
●For the installation location of a projector, it shouldn’t be seen in thedistanceoflessthan4meters foralongtime.
●Before operation, please confirm that all covers(housing) are on and screws tightened. It’s forbidden to use a projector
while covers(housing)areoff
●Keepthelampcleananddonottouchitwithbarehands.
●Whileoperating it, wear protectiveitems.
●Anyelectricalconnectionmustbecarriedoutbyaqualifiedperson.
●Beforeinstallation,pleaseconfirmthevoltagesupplied matcheswhat isrequiredforthe projector
●Eachprojectormustbeproperlyearthed andinstalled as perrelatedelectricalstandards.
●Donotusepower cordwithits insulatordamagedandconnectthe powercord with othercables.
●If the projector is not used or under cleaning,, please hold the plug and unplug it. Do not unplug it forcefully or by
pullingthepowercable.
●Allpowercordsmust conform to relatedsafetyandregulations
●Whilebeingoperated,theprojectorshouldnotbeunderrainsorinhumidity.

4
●Do not switch on and off the projector constantly in very short intervals, otherwise the light source’s and other
electrical parts’ life will be shortened .
●There are safety cord holes at the bottom of the base of a projector. In view of safety, please run the safety cord
supplied throughthesafetycord holesfor safety support.
●Before any installation, maintenance and cleaning work, please ensure the projector is disconnected from power
mains.
●.Afterstableoperationundernormalsituation, its temperatureis80℃.
●While the lamp is stricken for the first time, there will be smoke and strange smell. It’s normal and does not mean the
projectorhassomedefects.
●While it running, don’t touch the metal housing to avoid being burned!
●Donotmounttheprojectordirectlyoninflammablesurface.
●Do not project the beam straightly on combustible items and the minimum distance between the projector and
illuminateditemsis8m.
●Aprojector should be installed with good ventilation and the minimum distance between the projector and walls is
50cm.Atthesametime,pleaseensurethe fansandairinletsandoutletsareworkable.
●Donotletthefrontlensundersunlightorotherstronglightsourcesatanyangle,otherwisethedanger
offirecanbecaused bythe focused beambythe lensinsideaprojector.
●TheproductmeetsTheGeneralTechnicalRequirementsandStandardsforRecycleand UseOfExpiredAppliance
andElectronic Products.
●Whentheproductmeets disposal standardsand needs tobedisposed,aclient needstodisposeandrecycle it.
2. INSTRUCTIONS
●CLEANINGANDMAINTENANCE
Keeping a projector is necessary and thedust, oil and smoke should not accumulate onor in it, otherwise its light output will be greatly
compromised. Regular cleaning will ensure light output at maximum and reliable running during its whole life span. It’s advised to use
softclothwithgoodqualitydetergent.Underwhatevercircumstances, it shouldnot usealcoholor othersolvent.
Forthe accumulationofoiland smoke onthe front lens, thussharpdecrease in light output, the front lensshouldbe cleaned once every
week. Cooling fans cleaned once every month. Internal items inside the projector should be cleaned once every year using vacuum or
blower.Colorfilters,rotators andinternalmirrorsshould becleanedonceevery month.
Regular inspection of air filters and clean them before they fully blocked. Clean air filters at the bottom of the base. Please vacuum or
compressedairtocleanandputthembackaftercleaning.
●Beforeanymaintenanceandcleaning,pleaseensuretheprojectisoff thepower
●Onlyqualifiedpersonisallowedtodomaintenance
●During maintenanceandbeforemaintenance,theprojector mustbe off power.
●To avoid internal damage, sun light or other light mustn’t penetrate into the projector via front lens whether it
runsornot
●Donotusealcoholorotherorganic solventtocleanthehousingtoavoiddamage.
●Donotuseanysolventwithchemicalelementsto cleancolorfiltersorhot mirror.
.Hotmirrorshouldbecleanedevery3daysandcoatedwith
●LUBRICATION
To ensure smooth movement of gobos and zoom and focus lens, it’s advised rotators’ bearings and 2 sliding bars for zoom and focus
lensbelubricated every2 months.Highqualityandhightemperaturelubricant/grease is advised..

5
●TROUBLESHOOTING
PROBLEM
ACTION
The projector doesn’t switch on
Checkthe fuseonthepower socket.
Checkthelamp.
Thelampisonbuttheprojector doesn’t respond
to thecontroller
Makesurethatthe fixture’s start address is right
ReplaceorrepairtheXLRsignalcable.
The projectorfunctionsintermittently
Makesurethefanisworkingwellorfansandtheirshieldsarenotblocked
Beamappearsdim, Lowinbrightness
Make sure the lamp is withinitslifespan
Removedustor grease fromthelenses.
Theprojectimageappearstohavea halo
Carefullycleanthelamp,opticallensesandothercomponents.
HeavilyDefectiveBeam
Checkif lensareingoodcondition(notcracked)
Cleandustorgreaseonthelens.
3. APPEARANCE
4. INSTALLATION
Aprojector can be placed on the stage floordirectlyor mounted on a truss at any direction without impacting itsperformance. Please
use a safety cord, which can support 10 times the weight of the projector, while mounting it on the truss. The safety cord should be
used with magazine witha lock. Just as the figuresbelow, please run the safety cord through the holesat the bottomof the base and
aroundthetruss.
● RIGGING
1. Use M12 bolt to fix the clamp(1) into the omega holder (3), run the bolt through the holder’s holes
2. Push2quick-lockfasteners(4)intoholesatthebottomofthebase,fix themand tighten themclockwise
3.Run safetycord(2)through holesatthebottomofthe baseandaround thetruss(6)
Head
Arm
Base

6
Usethespanner suppliedwitha projectortohelpinstallation.
WARNING:
●TheprojectorMUSTbeliftedorcarriedbytheHANDLESinsteadofclamps.
●.Forsafetythesafetycordshouldafford10timestheProjector’s weight.

7
It must use secondary safety accessory like appropriate net. The structures of the secondary accessory must ensure that while
malfunction happens, the installed parts won’t fall to the ground.
While rigging, mounting or maintaining, the projector mustn’t be placed in the areas listed hereinafter: the bridge, high work areas
or otherdangerous areas.
Theoperatorof the projector orits related safety items must be accepted by safetyexperts before first launching or re-running after
anyreplacementsorrepairing.
The operator must ensure a test before acceptance every 4 years and the related safety measures and installation accepted by
experts.
The operator must ensure the related safety measures and its installation must be approved by the technicians every year. The
projector may be installed in places under which people may walk by or sit. Important! Installations in high places requires wide
experience, including but not limited to load limit calculation, the installing materials needed and regular inspection of installing
materials and the projectors. If lacking the qualifications, please don’t try installation by yourself, but seek help from professionals
using designated lifting gears.Abnormalinstallation maycausebodyharmorpropertydamages.
The projectors must be installed in places where people can’t reach. If they are removed from ceiling or high places, professional
truss mustbe used.Itisforbiddentoletanyprojector movefreelyinaroomafterinstallation.
Note: Device falling down can cause heavy body harm! If you have any questions about its safety, don’t install any projector!
Beforeinstallation, please ensuremounting areascan endure 10times the weightof aproject atleast.
●POWERCONNECTION
Connect thepowercordasfollows:
L(live)=brown
E(earth)=yellow/green
N(neutral)=blue
Before power connection, please ensure the power supplied must match what the nameplate says. It is recommended that each
projectorbeconnectedwithpowerseparatelyso thattheymaybeindividuallyswitched onandoff.
●The earth wire(yellow/green)mustbe connected to the ground. And electrical connection
mustbeinaccordancewiththestandardsconcerned.
●If any questions about the electrical installation, do not continue but consult a qualified
electrician.
●DMXCONTROLCONNECTION
Connection between controller and projector and between one projector and another must be made with a twin-screened cable, with each
wire having at least a 0.5mm in diameter. Connection to and from the projector is via cannon 5 pin (which are included with the projector)
or5pin XLR plugsand sockets.The XLR's are connectedasshown in the figure above.
Note: care should be takento ensure that none ofthe pinstouch the metallic bodyof the plug or eachother. XLR plugs and sockets mustn’t
be connected in any way other than mentioned in the above figure. The XR330BWS accepts digital control signals in protocol DMX512
(1990).
Connect the controller’s DMX output to the first fixture’s DMX input, and connect the first fixture’s DMX output to the second fixture’s
DMX input and connect the rest fixtures in the same way. Eventually connect the last fixture’s DMX output to a DMX terminator asshown
inthefigurebelow.

8
●DMXTERMINATOR
In the Controller mode, atthe last fixture in the chain, the DMX output has to beconnected witha DMXterminator.Thispreventselectrical
noisefromdisturbingandcorruptingtheDMXcontrolsignals.
The DMX terminator is simply an XLR connector with a 120(ohm) resistor connected across pins 2 and 3, which is then plugged into
theoutputsocketonthelastprojectorinthechain.Theconnectionsareillustratedbelow.
● ALIGNMENT/INSTALLATION/REPLACEMENTOFALAMP
1. Loosen and remove screws B,C and D .Loosen screw A which can only be loosened but can’t be removed, for details please see the
figureontheright.Thenthelamp and itssupporting framescanbe seen.
2. Loosen screws E and F and push the lamp supporting frames downward to expose the lamp’s side, and remove the lamp after
pushingit downward. After unplugging the lamp, remove it. Plug a newlamp with lamp wires after it is in place, push the supporting
frames upward and tighten the screws to fix the new lamp. Tighten the screws after the lamp chamber cover is on. At last restore the
projector’s original appearancebasedontheopposite sequencesofdismantling.
DMX512 OUTPUT INPUT
DMX
terminator
OFF
ON FUSE 250V 8A
POWER I N POWER OUT DMX IN DMX OUT OFF
ON FUSE 250V 8A
POWER I N POWER OUT DMX IN DMX OUT OFF
ON FUSE 250V 8A
POWER I N P OWER O UT D MX IN DMX OUT
OUTPUT INPUT
21
3
120
DMX TERMINATOR
CONNECTION
Connect a 120 (OHM) resistor
across pins 2 and 3 in an XLR plug
and insert into the DMX out socket
on the last unit in the chain. PIN 3
PIN 2
A B
C
D
E
F

9
● GOBOREPLACEMENT
1.Disconnecttheprojectorwithmainspowerandlet it cool
2.Afterloosening4 1/4 fastenersofthehead cover, removeit
3.Gentlypullthe goboholder(3)fromrotatinggobowheelupward.
4. Use appropriate tool like flat screwdriver of small size to remove spring lock(1). Do not use bare hand to touchpattern side of the
gobo.
5. Remove the old gobo(2) and insert new one with the smooth side facing light source. At the edge of the Gleelite gobo, there is
small positioning point(8), which must overlap with gobo holder’s positioning point(4). Insert spring lock and fix the gobo inside
the gobo holder.
6. Insert the gobo holder into the rotating gobo wheel via locking pins (6 and 7) and ensure positioning point (4) overlaps extruding
point in the shape of tooth at the edge of the rotating wheel(5). Important! After inserting rotators into the wheel, the neighboring
rotators must be positioned based on same rules, which means positioning point(4) must overlap extruding point(5) at the edge of
the wheel. With2 markings (4) and (5), whenthe wheel is at properposition where the rotators canbe inserted, the rotatorscanbe
placedonebyone.
7.Before power on,please installthehead cover.
8.Use menutofinetunereplacedgobos( Service->Calibration->Standardeffect->R. Gobo Indexing 1…R Gobo Indexing(6)
Note:The magnet(9) in the gobo holder isofthe same functionasthe positioning point(4).
DANGER！
BEOFOREGOBOREPLACEMENT,ITMUSTBEOFFPOWER！

10
5. SETUPAND CONFIGURATION
●FRONT PANEL OPERATION
To browse through or view a projector’s function settings, push any key to activate the screen after power-on.. After screen
unlocked, push both key and to enter into menus. Each main menu has its sub-menus with different special functions, for
detailspleasesee the5th pointhereinafterOPERATION MENU.
1、Under menupageforfunctionsettings，push or toselectfunctiondesired.
2、During menuoperation ，keyis toescape，keymeansENTER，push keytosavesettingsorenter into
submenus，push or keyto changevalues（plusorminus）.
Push keytogo backtouppermenu.Ifnot,thescreen willgoback toinitialdisplayautomatically.
●DMXSTARTADDRESS
Pushanykeytoenter into options interface.
If multiple projectors are controlled by DMXcontroller, each projector must have its own DMXaddressto receive DMX signals fromthe
controller and respond to them. The projector has 2 DMX modes. There are short mode and standard mode. For example standard mode
has 23 channels, so set the No. 1 projector’s address 001, No. 2 projector’s address 024, No. 3 projector’s address 047, No. 4 projector’s
address70andsoon.
Turnona projectorandpushanykey toenterinto options interface
SelectCHANNELMODEiconandpushENTERkey .SelectDMXADRESSin2nd level menu tosetstartaddress
PushkeyUP orDOWN tosetvaluedesired.
PushENTERkey toconfirmit.
PushESCAPEkey toenter intoupper level menus.
●STAND-ALONEMODE
Without connecting a projector with a controller via XLR cable, after preset memories under the master mode enabled, it
will run in Stand-Alone mode.
●MASTER/SLAVEMODE
(1)Editthescenedesired
Two ways toeditscene
a. Editmanually
Disconnect a projector from XLR cable and enter into scene editing via control panel. Ascene has 20 steps and select any step via its
sequence No.. Enter into channel control to edit its data. After disconnected from a DMX controller, a projector will respond to data
edited simultaneously.
b. Editwithhelpofa DMXcontroller
Use a DMX controller to control a projector. After the projector is controlled properly in positions, select the sequence No. of step to
besavedandclickto storeDMXvalues.
Current DMX data will be automatically saved to its scene’s data and the sequence NO. added 1. And so on, it can save 20-stepscene.
(2) Select usemodefromscenemenu.There are2modesforselection: single andrecycle.If notused,itcanbe closed.

11
6. OPERATIONMENU
Menu interface:1. DMXaddress 2. Config3. Manual control 4. Scene5. Systemsettings 6. Information
1) Explanationsformenu functions.Push anykeytoenterintooptioninterface while atinitial display
Main menu
1st levelmenu
2nd levelmenu
Description
DMX
address
DMXSetting
001-512
Select “DMX address”option
1）AfterENTERkeypushed，thecurrentDMXaddresswill
be shown
2）PushUPorDOWNkeytosetaddress
3）PushENTERkeytosave andexit.PushESCAPEkeyto
exitdirectly
Config
Channel mode
19CH
ShortMode
Select ”Channel mode” option
1）AfterENTER keypushed,currentchannelmodewillbe
shown(20CHfor standard mode,16CH for shortmode)
2）PushUPorDOWNkeytoselecteitheroftheoptions；
3）PushENTERkeytosave the modeselected.PUSH
ESCAPEkeytogobacktotheupperlevelmenu and
cancelthemode selected
23CH
Standardmode
LampStriking
Auto lamp-on
Select “Lamp Striking”Option
1）PushENTERkeytoshowcurrentmode(Auto lamp-on,
lamp-on byDMXcontrol).
2）PushUPorDOWNkeytoselecteitheroftheoptions.
3）Push ENTER key to save the mode selected. PUSH
ESCAPE key to go back to the upper level menu and cancel
themode selected
Lamp-on byDMXcontrol
Pan&Tilt
Pan Invert
Select“Pan and Tilt Invert”option
1）Push ENTER key and the options will be shown on the
display（OpenorClose）
2）PushUPorDOWNkeytoselecteitheroftheoptions.
3）Push ENTER key to save the selected. PUSH ESCAPE
keytocancelthesetting.
TiltInvert
PanandTiltswap
Select“Pan and Tilt Swap”option
1）Push ENTER key and the options will be shown on the
display（OpenorClose）
MASTER SLAVE SLAVE
OFF
ON
FUSE 25 0V 8 A
POWER IN POWER OUT DMX IN DMX OUT
OFF
ON
FUSE 25 0V 8 A
POWER IN POWER OUT DMX IN DMX OUT
OFF
ON
FUSE 25 0V 8 A
POWER IN POWER OUT DMX IN DMX OUT
OUTPUT INPUT OUTPUT INPUT DMX
terminator

12
2）PushUPorDOWNkeytoselecteitheroftheoptions.3）
Push ENTER keyto save the selected. PUSH ESCAPE key
tocancelthesetting.
GOBO
Calibration
GOBO1
GOBO2
GOBO3
GOBO4
GOBO5
GOBO6
GOBO7
1）Push ENTER key and the quantity of the shift will be
shownonthedisplay
2）PushUPorDOWNkeytosettheshiftquantity.
3）Push ENTER key to save the selected. PUSH ESCAPE
keytoexitdirectly.
Channel
calibration
（Hidden ）
PushbothUPandDOWN keystoenter intothemenu，
pushDOWNor UPkeyto select,pushENTER keytosave.
Lampcontrol
Open
Select“Lamp Control”option
1）PushENTERkeyand theoptionswillbeshownonthe
display（OpenorClose）
2）PushUPorDOWNkeytoselecteitheroftheoptions.
3）Push ENTER key to save the selected. PUSH ESCAPE
keytocancelthesetting.
Close
Manual
control
Lamppower
Fullpower
Select“Lamp power”option
1）PushENTERkeyand theoptionswillbeshownonthe
display（Fullorhalfpower）
2）PushUPorDOWNkeytoselecteitheroftheoptions.
3）PushENTERkeytosave the selected.PUSH ESCAPE
keyto cancelthesetting.
Halfpower
Systemreset
Headreset
Select“System reset”option
1）PushENTERkeyand the resetoptionswillbeshownon
thedisplay（Headreset,panandtiltresetand totalreset）
2）PushUPorDOWNkeytoselectanyoftheoptions.
3）PushENTERkeytosave the selected.PUSH ESCAPE
keytocancelthesetting.
PanandTiltreset
Totalreset
Scene
Mode
Close
Select“Mode”option
1）PushENTERkeyand theoptionswillbeshownonthe
display（Close, singleand cycle）
2）PushUPorDOWNkeytoselectanyof theoptions.
3）PushENTERkeytosave the selected.PUSH ESCAPE
keytocancelthesetting.
Single
Cycle
Select“Scene”options
1）PushENTERkeyand theoptionswillbeshownonthe
display（No.,Effectiveand time）
2）PushUPorDOWNkeytoselectanyof theoptions.
3）PushENTERkeytosave the selected.PUSH ESCAPE
keytocancelthesetting.
Sequence No
1-20
Effective
Yes
No
Time
3.0
Save DMX
value
Yes

13
Cancel
Channel
control
DMXChannel
Select“Channel control”options
1）PushENTERkeyand theoptionwillbeshownon the
display（allDMXchannels）
2）PushUPorDOWNkeytoenterinto anyofthe
options(adjustablebetween0and 255).
3）Push ENTER key to save the selected. PUSH ESCAPE
keytocancelthesetting.
System
settings
Languages
Chinese
Select“Language”options
1）PushUPorDOWNkeytoselecteitheroftheoptions.
2）PushENTERkeytosave the selected.PUSH ESCAPE
keytocancelthesetting.
English
Display
Normal
Select“Display”options
1）Push ENTERkeyand the waythescreen displayed will
be shown
2）PushUPorDOWNkeytoselecteitheroftheoptions.
3）PushENTERkeytosave the selected.PUSH ESCAPE
keytocancelthesetting.
Invert
Backlight
Auto
Select“Backlight”options
1）PushUPorDOWNkeytoselecteitheroftheoptions.
2）PushENTERkeytosave the selected.PUSH ESCAPE
keytocancelthesetting.
On
Factorysettings
Yes
Select“Factory settings”options
1）PushUPorDOWNkeytoselecteitheroftheoptions.
2）PushENTERkeytosave the selected.PUSH ESCAPE
keytocancelthesetting.
Cancel
Information
1. Totalhours （H）
2. Lamptime（min）
3. TheNo.Lamp
replacements
4. replace Lamp
5. Fanvoltage
6. Errormessages
7. About
Select“Information”options
1）PushENTERkeyand theinformationwillbeshown
2）PushUPorDOWNkeytoselectanyof theoptions.
3）PushENTERkeytosave the selected.PUSH ESCAPE
keytocancelthesetting.
7. DMX PROTOCOL
PR-2393AdoubleprismDMXchart
DMX channel
Value
Function
Short Mode
Standard
Mode
1
1
Pan
0-255
0-100%
2
Pan Fine
0-255
0-100%
2
3
Tilt
0-255
0-100%

14
4
Tilt Fine
0-255
0-100%
3
5
Pan andTilt speed
0-255
Fast->Slow
4
6
Strobe
0-3
Close
4-103
Strobe:Slow->Fast
104-107
Open
108-207
Pulse strobe:Slow->Fast
208-212
Open
213-225
Strobeatrandom:slowspeed
226-238
Strobeatrandom:mediumspeed
239-251
Strobeatrandom:fastspeed
252-255
Open
5
7
Dimmer
0-255
0-100%
6
8
Colors
0-4
Open
5-9
Color1
10-14
Color2
15-19
Color3
20-24
Color4
25-29
Color5
30-34
Color6
35-39
Color7
40-44
Color8
45-49
Color9
50-54
Color10
55-59
Color11
60-64
Open+Color1
65-69
Color1+Color2
70-74
Color2+Color3
75-79
Color3+Color4
80-84
Color4+Color5
85-89
Color5+Color6
90-94
Color6+Color7
95-99
Color7+Color8
100-104
Color8+Color9
105-109
Color9+Color10
110-114
Color10+Color11
115-119
Color11+Open
120-185
Clockwiserotation:Fast->Slow
186-189
Stop
190-255
Anti-clockwiserotation:slow->fast

15
7
9
Effectwheel
0-9
Open
10-255
Flowingwatereffect ：Slow->Fast
8
10
Fixed gobowheel
0-4
Open
5-9
GOBO1
10-14
GOBO2
15-19
GOBO3
20-24
GOBO4
25-29
GOBO5
30-34
GOBO6
35-39
GOBO7
40-44
GOBO8
45-49
GOBO9
50-54
GOBO10
55-61
GOBO1 SHAKE:Slow->Fast
62-68
GOBO2 SHAKE:Slow->Fast
69-75
GOBO3 SHAKE:Slow->Fast
76-82
GOBO4 SHAKE:Slow->Fast
83-89
GOBO5 SHAKE:Slow->Fast
90-96
GOBO6 SHAKE:Slow->Fast
97-103
GOBO7 SHAKE:Slow->Fast
104-110
GOBO8 SHAKE:Slow->Fast
111-117
GOBO9 SHAKE:Slow->Fast
118-124
GOBO10SHAKE:Slow->Fast
125-187
Clockwiserotation:Fast->Slow
188-192
Stop
193-255
Anti-clockwiserotation:slow->fast
9
11
RotatingGOBOwheel
0-9
Open
10-19
GOBO1
20-29
GOBO2
30-39
GOBO3
40-49
GOBO4
50-59
GOBO5
60-69
GOBO6
70-79
GOBO7
80-89
GOBO1 SHAKE:Slow->Fast
90-99
GOBO2 SHAKE:Slow->Fast
100-109
GOBO3 SHAKE:Slow->Fast
110-119
GOBO4 SHAKE:Slow->Fast
120-129
GOBO5 SHAKE:Slow->Fast
130-139
GOBO6 SHAKE:Slow->Fast
140-149
GOBO7 SHAKE:Slow->Fast

16
150-202
Clockwiserotation:Fast->Slow
203-255
Anti-clockwiserotation:slow->fast
10
12
GOBORotation
0-127
Positioning:0-360°
128-191
Clockwiserotation:Fast->Slow
192-255
Anti-clockwiserotation:slow->fast
11
13
16facet prism
0-127
No
128-191
Prism 1in
192-255
Prism 2in
12
14
16facet prismrotation
0-127
0-360°
128-191
Clockwiserotation:Fast->Slow
192-255
Anti-clockwiserotation:slow->fast
13
15
8facet prism
0-127
No
128-191
Prism 1in
192-255
Prism 2in
14
16
8facet prismrotation
0-127
0-360°
128-191
Clockwiserotation:Fast->Slow
192-255
Anti-clockwiserotation:slow->fast
15
17
Frost
0-255
0-100%
16
18
Zoom
0-255
0-100%
19
Zoom Fine
0-255
0-100%
17
20
Focus
0-255
0-100%
21
Focus Fine
0-255
0-100%
18
22
Reset
0-25
NO
26-76
Headreset
77-127
Pan &Tilt reset
128-255
Total reset
19
23
Lampcontrol
0-25
No
26-100
Lampoff
101-255
Lampon

17
8. ERRORMESSAGE
Name
Type
Correction
Pan
Optical sensorerror:Pan
Checkifwiring, optical sensor and motorsare normal
Tilt
Optical sensor error:Tilt
Checkifwiring, optical sensor and motorsare normal
Pan&Tilt driverboard
Communicationerror:module1
Checkifwiring, hall sensorandmotorsarenormal
Motordriverboard
Communicationerror:module2
Checkifwiring, hallsensorandmotorsarenormal
Focus
Hall error: Focus
Checkifwiring, hallsensorandmotorsarenormal
Zoom
Hall error:Zoom
Checkifwiring, hallsensorandmotorsarenormal
Effectwheel
Hall error: Effectwheel
Checkifwiring, hall sensorandmotorsarenormal
Colorwheel
Hall error:Color wheel
Checkifwiring, hallsensorandmotorsarenormal
Fixed gobowheel
Hall error:Fixedgobowheel
Checkifwiring, hallsensorandmotorsarenormal
Rotatinggobo wheel
Hall error: Rotatinggobowheel
Checkifwiring, hallsensorandmotorsarenormal
Lampstriking
Lampstrikingerror
Check if wiring and igniter are normal and if the voltage of
theigniterisnormal
9. TECHNICALDATA
ELECTRICPARAMETERS
Inputvoltage200V~240VAC，50/60Hz
Inputpower500W@230V
Power factor PF>0.90
THESPECIFICATIONSOFTHELIGHTSOURCE
Lamp MSDPlatinum300SFlex
Color temperature 7800K+/-300K
rated life 6000hrs
COLORS
1colorwheel: 11colors+Open
FIXEDGOBOWHEEL/EFFECTWHEEL
1 fixed gobo wheel:10gobos+open,gobo diameter=6.5mm, itsthickness=0.5mm
1fireeffectwheel

18
ROTATINGGOBOWHEEL
1rotatinggobowheel:7gobos+open
GobodiameterФ12.5mm, 2.2mm thick
1
2
3
4
5
6
7
PRISM/FROST
1 8-facetprismand1 16-facetprism, bi-directionalrotationfromslow tofast
FOCUS
DMX linear focus
DIMMER /STROBE
Strobeat variablespeeds(15 F.P.Satmaximum)
0-100%lineardimmer
HEADMOVEMENT
Pan540º,Tilt 270ºwith 16bitcontrol
BEAMANGLE
Beam:2°～20°
Spot:6°～30°
Wash:17°～45°
CONTROL
Projectorandlampinformation readable, externalDMX valuereceived and thermalsensorbuilt-inforerror and malfunctionanalysis
Preset memory
Unintentionalheadmove tocausepower-off, quietfansforcooling
1
1
1
1
1
1

19
InternationalstandardDMX512 protocol,5-pininterface
19channelsinshortmode and23channelsinstandardmode
OPTIONALWIRELESSCONTROLMODULE/RDMMODULE
CompliantwithUSITTDMX-512（1986 and 1990）and 512-AFullDMXforfidelityandDMXframingintegrity
Auto-detectingDMXframingsizeandspeed
<5msDMXdelay
Frequencyrange2402-2480MHz
HOUSING
HightemperatureABSand aluminum,IP20
NETWEIGHT
19Kg
OPERATIONTEMPERATURE
Ambienttemperatureatmaximum：40°C
SIZES:
LIGHTOUTPUT:
609
382
347
393
515
299
2° DIAMETER (m)
DISTANCE (m) 0m 10m 20m 30m
0.31 0.64 1.21
0
2.9°
2°Lux 420000 105600 45600
0
60°
40° DIAMETER (m)
40°Lux 05200 2380 960
3.9 7.7 11.50
0

20
10. CIRCUITDIAGRAM