Prevue Hendryx 58502 User manual

58502—06/22 — A4.1 Made in China for Prevue Pet Produ ts, In ., 224 N Maplewood Ave, Chi ago IL 60612 USA • 1 [312] 243-3624 • www.prevuepet. om • ustomerservi e @ prevuepet. om
KEY:
L = Left ide
B = Back
F= Front
R = Right ide
CR = Center/Roof
CM = Center/
MidLevel Floor
CG = Center/
Floor Grille
CT = Center/Tray
C = Center/ helf
F rr t Stack | Two Story
PARTS LIST
Instructions online at www.prevuepet.com
]Cg
]Cm
]Cr
]L3
]L2
]L1
]Cs
]Ct
]B3
]B2
]B1
]F3
]F2
]F1
]R3
]R2
]R1
CUSTOMER SUPPORT
Please contact Prevue Pet Products:
PHONE [phone]
ONLINE www.prevuepet.com
EMAIL [e-mail]
These pieces are
interchangeable:
]L1 = ]R1
]L2, ]L3, ]R2,
]R3 are all the same
⁕
PLATFORMS
HAMMOCK
RAMPS
HARDWARE
& TOOLS :
H x
Scr ws
28 pcs
Cast rs
4 pcs
H x K y
58502
MODEL
#

Orient the front legs (F1)
with the windbell lock
facing forward.
The extended portion of
the tray hannel rail (L1)
dovetails into the inside of
the frame leg.
Attach frames together
with a hex screw through
the bottom hole.
Orient the ba k legs (B1)
with the tray channel
backstop facing the back.
Attach legs to sides with
hex screws in the bottom
holes.
Attach the shelf (C ) with
hex screws through the
holes near the base
of the legs.
HOW TO TELL THE DIFFERENCE : everal parts and panels may look similar. Here’s how to tell the difference:
58502—06/22 — A4.2 For more wonderful ages, toys, and a essories for ats, birds, hi kens, rabbits, ferrets, dogs and small animals, visit www.prevuepet. om
NO ADDITIONAL TOOL REQUIRED • For best results, follow the Assembly teps in the order presented.
× 8
FRONT & BACK PANELS :
TOP vs BOTTOM
The bottom panels (F2 & B2)
have brackets on the corners.
Top panels (F3 & B3) do not.
KEY:
L = Left ide
B = Back
F = Front
R = Right ide
CR = Center / Roof
CM = Center / Mid-
Level Floor
CG = Center /
Floor Grille
CT = Center / Tray
C = Center /
helf
1PIECES
]L1
]R1
]F1
]Cs
]B1
interchangeable
windbell lock
Cr
Cm
Cg
Cs
CENTER PANELS
The roof panel (CR) has an attached
sliding door on top, and a screw hole
on both ends of the frame.
The midlevel floor panel (CM) has
a detachable wire divider door, and
a screw hole on both ends of the
frame.
The ground floor grille panel (CG)
has NO door and NO screw hole on
the ends.
The shelf (C ) is longer, and has
threaded screw holes on the front
and back corners of the frame.
F rr t Stack | Two Story
ASSEMBLY
Instructions online at www.prevuepet.com
CUSTOMER SUPPORT
Please contact Prevue Pet Products:
PHONE [phone]
ONLINE www.prevuepet.com
EMAIL [e-mail]
58502
MODEL
#

58502—06/22 — A4.3 Made in China for Prevue Pet Produ ts, In ., 224 N Maplewood Ave, Chi ago IL 60612 USA • 1 [312] 243-3624 • www.prevuepet. om • ustomerservi e @ prevuepet. om
2PIECES
3PIECES tand the side panel (L2) and the lower
ba k panel (B2) (with corner brackets)
in position and attach together with a hex
screw at the top and bottom corners. →
Continue adding and attaching the
right side (R2) and front (F2) panels
with hex screws at the top brackets.
↘
Finish by adding screws around the base,
in the open holes of the bottom brackets. →
interchangeable
Hand-tighten the screws so they
remain loose. This will ease the
assembly of the next level.
⁕
]L2
]R2
]F2
]Cm
]Cg
]B2
× 10
Turn the assembled unit
upside down. Fully insert
a aster in each leg.
Turn it right-side up and set
the floor grille (CG) in place.
Place the midlevel floor (CM) (with the
removeable divider door) in place
and secure it with a hex
screw on each end.
↘
CASTERS

Assembly completed. {
58502—06/22 — A4.4 For more wonderful ages, toys, and a essories for ats, birds, hi kens, rabbits, ferrets, dogs and small animals, visit www.prevuepet. om
4PIECES Follow the assembly method from tep 3:
Place the left side (L3) and upper ba k (B2)
(no brackets) panels in place and attach
together at the top with a hex screw. →
Continue adding and attaching the right side
(R3) and front (F3) panels with hex screws at
the top and bottom corners.
↘
Hook a ramp onto the
underside of a platform,
and positioned at the cage
front. Place the platform
in the lower level, on the
middle horizontal wire.
Remove the divider door. Hook a ramp on
the wire loops, and rest the other end on
the platform below. NOTE: The divider may
be reattached with the ramp installed.
Tighten s rews over the
entire age with the hex
key, until all are snug.
⁕
5PIECES
interchangeable
]L3
]R3
]F3
]Cr
]Ct
]B3
× 10
Place the roof (CR) (with the attached sliding
door) in position and attach with a hex screw
on each end.
↓
Add the remaining
ramp and platform
in the upper level.
Add the hammo k.
Rotate the windbell
lock up to slide the
tray into place.
PLATFORMS
HAMMOCK
RAMPS