Prevue Hendryx 58503 User manual

58503—06/22 — A4.1 Made in China for Prevue Pet Products, Inc., 224 N Maplewood Ave, Chicago IL 60612 USA • 1 [312 243-3624 • www.prevuepet.com • customerservice @ prevuepet.com
HARDWARE
& TOOLS :
KEY:
L = Left ide
B = Back
F= Front
R = Right ide
CR = Center/Roof
CM = Center/
MidLevel Floor
CG = Center/
Floor Grille
CT = Center/Tray
C = Center/ helf
Ferret Sta k | Three Story
PARTS LIST
Instructions online at www.prevuepet.com
]Cg
]Cm2
]Cm1
]Cr
]L1
]Cs
]Ct
]B3
]B2
]B1
]F3
]F2
]F1
]R3
]B4
]F4
]R4
]R2
]L3
]L4
]L2
]R1
Hex
S rews
38 p s
Casters
4 p s
CUSTOMER SUPPORT
Please contact Prevue Pet Products:
PHONE [phone]
ONLINE www.prevuepet.com
EMAIL customerservice @prevuepet.com
These pieces are
interchangeable:
]L1 = ]R1
]Cm1 = ]Cm2
]L2, 3, 4
]R2, 3, 4
⁕
PLATFORMS
HAMMOCK
RAMPS
58503
MODEL
#
are all
the same
Hex Key

Orient the front legs (F1)
with the windbell lock
facing forward.
The extended portion of
the tray channel rail (L1)
dovetails into the inside of
the frame leg. Attach frames
together with a hex screw
through the bottom hole.
Orient the backstop on the
back legs (B1) facing the back.
Attach legs to sides with hex
screws in the bottom holes.
Attach the shelf (C ).
HOW TO TELL THE DIFFERENCE : everal parts and panels may look similar. Here’s how to tell the difference:
58503—06/22 — A4.2 For more wonderful cages, toys, and accessories for cats, birds, chickens, rabbits, ferrets, dogs and small animals, visit www.prevuepet.com
NO ADDITIONAL TOOL REQUIRED • For best results, follow the Assembly teps in the order presented.
× 8
FRONT & BACK PANELS :
TOP vs OTHERS
The lower panels (F2, F3, B2,
B3) have top corner brackets.
Top panels (F4, B4) do not.
KEY:
L = Left ide
B = Back
F = Front
R = Right ide
CR = Center / Roof
CM = Center /
Mid-Level Floor
CG = Center /
Floor Grille
CT = Center / Tray
C = Center / helf
1PIECES
]L1]R1
]F1
]Cs
]B1
interchangeable
windbell lock
Cr
Cm
Cg
Cs
CENTER PANELS
The roof panel (CR) has an attached
sliding door on top, and a screw hole
on both ends of the frame.
Both midlevel floor panels (CM)
have a detachable wire divider door,
and a screw hole on both ends of the
frame.
The ground floor grille panel (CG)
has NO door and NO screw hole on
the ends.
The shelf (C ) is longer, and has
threaded screw holes on the front
and back corners of the frame.
Ferret Sta k | Three Story
ASSEMBLY
Instructions online at www.prevuepet.com
CUSTOMER SUPPORT
Please contact Prevue Pet Products:
PHONE [phone]
ONLINE www.prevuepet.com
EMAIL customerservice @ prevuepet.com
58503
MODEL
#
2PIECES
]Cg
Turn the unit over.
Fully insert a caster
in each leg.
Flip the unit upright. et
the floor grille (CG)
in place.
CASTERS

58503—06/22 — A4.3 Made in China for Prevue Pet Products, Inc., 224 N Maplewood Ave, Chicago IL 60612 USA • 1 [312 243-3624 • www.prevuepet.com • customerservice @ prevuepet.com
3PIECES ↙tand the side panel (L2) and the lower
back panel (B2) (with corner brackets)
in position and attach together with a hex
screw at the top and bottom corners.
Repeat the assembly of tep 3 with the duplicate panels:
front & back panels (F3, B3 —with brackets) and side panels
(L3, R3). Attach together with hex screws in the top and
bottom corners.
↙
→Continue adding and attaching
panels [side panel (R2), front panel
(F2)], with hand-tightened hex
screws as detailed above.
interchangeable
Hand-tighten screws so they
remain loose. This will ease the
assembly of the additional levels.
⁕
]L2
]R2
]F2
]Cm1
]B2
× 10
4PIECES
interchangeable
]L3
]R3
]F3
]Cm2
]B3
× 10
←Place one of the midlevel floors (CM1,
or CM2 – with the removeable divider
door) in place and secure it with hex
screws, one screw on each end.
Place the midlevel floor (CM – with
divider door) in place and secure it
with hex screws, one on each end.
↓

Assembly completed. {
58503—06/22 — A4.4 For more wonderful cages, toys, and accessories for cats, birds, chickens, rabbits, ferrets, dogs and small animals, visit www.prevuepet.com
5PIECES ↙
Repeat the assembly method from
teps 3 & 4:
The remaining front & back panels
(F4, B4) will not have brackets in the
upper corners.
Add and attach front, back, and side
panels (R4, L4) as before, with hand-
tightened hex screws at the top and
bottom corners.
Hook a ramp onto the
platform and positioned at
the cage-front end. Place
the platform/ramp in the
lower level, on the middle
horizontal wire.
Remove the divider door. Hook a ramp on
the wire loops, and rest the other end on
the platform below. NOTE: The divider may
be reattached with the ramp installed.
Install the remaining platforms and
ramps in the same manner.
Tighten the screws over the entire cage with the hex key until all screws are snug.
⁕
6PIECES
interchangeable
]L4
]R4
]F4
]Cr
]Ct
]B4
× 10
→
Place the roof (CR – with the non-removable
sliding door) in position and attach with a
hex screw on each end.
Add the hammock.
Rotate the windbell
lock up and slide the
tray into place.
PLATFORMS
HAMMOCK
RAMPS