quadient IS-350 User manual

INSTALL THE HAND FEED TABLE AT THE LEFT OF THE BASE:
t the slots of the Base over the tabs of the table.
CONNECT THE LAN to a network RJ45 plug of the Base and
to the LAN wall socket using the LAN cable B.
OPEN THE BASE COVER, remove the headset protecting
strips and insert the headset in its compartment, then push
the headset back until it clicks.
WRITE DOWN THE PSD number, you may need the number
later.
INSTALL THE PSD in the slot and then close the cover. CONNECT THE SYSTEM POWERPLUG. Follow the installation wizard on the screen. Refer to the installation section in the User Guide.
IS-350 QUICK INSTALLATION GUIDE
BC
CAUTION: use a solid and steady table, far
from any door or fan.
2 4
7
5
3
6
C
A
1Check the box contents.
For more information about your mailing
system, please visit:
kbhelp.quadient.com/is350_dl

2c
13
4
2a
2b
IS-350 QUICK START GUIDE
1st Letter
20/01/20
Mem: None
Acc t : 11
0000
0 g
No services
1st Letter
No services
20/01/20
0000
0 g
For more specific information about your
mailing system, see the User Guide :
Press :
To reset the mailing system
Key the postage in directly
If you know the amount...
Choose rate and services
When the weight is displayed...
Print the stamp
4155895G/B - 30/03/2020
Put your mail on the scale
To weigh your mail...
or
When the postage is displayed...
Enter the weight manually
Screen main areas
Shortcut keys
Getting to know your mailing system Applying postage
If jamming occurs...Changing the ink cartridge Adding credit
kbhelp.quadient.com/is350_ug_en_dl
1
2
1
2
1
2
Type the amount on the keyboard.
Press OK.
The home screen
displays the postage.
1
1
2
Press to start the motors of your mailing
system.
Insert the mail piece in
the mail path, the
stamp printing position
on the upper right side.
Current rate and selected
services are displayed in
this area of the screen.
Rate and services
Date printed
Weighing type
Imprint position oset
Postage and weight
Job memory (can contain rate, stamp settings
and account)
Current account
D1
D2
D3
D4
D5
D6
D7
K1
K2
K3
K4
K5
K6
K7
K8
Rates and services selection
Job memories (rate, stamp settings, account)
Weighing modes
Credit management
Type of imprint and imprint settings
Sleep / wake (amber / green)
Stops printing
Starts printing
Check that the D3 icon is .
Otherwise press and then select the
option Standard weighing.
Press and then select the option
Manual weight entry.
Enter the weight and press OK.
Press OK to validate your selection and
return to the home screen.
Use the keypad to select an available Class
and/or Services, or select key 8 for the
wizard.
Press , type 2 and follow instructions onscreen.
Note: to complete this operation successfully, your postal
services account must have a positive credit balance of the
corresponding amount.
To change the rate and/or add services:
Press .
The Rate selection
screen is displayed.
Press on the control
panel to stop the motor.
Under the base, lift up
the release handle and,
using your other hand,
remove stuck envelope.
1
2
On the new ink cartridge,
remove the protective
strips from the printing
heads.
Raise base cover and
follow instructions printed
on sticker inside.
1
2
To clear the information on the screen.
To wake the machine up with default
settings.
To return to the home screen
D5
D6
D7
D1
K7
K8
K6
K2
K3
K4
K5
K1
D4
D3
D2
0000
0 g
1st Letter
No services
0000
0 g
Standard
1
Registered
3
Express
5
Courier
2
Priority
4
Wizard
6
2
3