RainPoint ITV101P User manual

ITV101P
Digital Faucet Timer with 3 Watering Plans
USER MANUAL
EN - 1DE - 19 FR - 36 IT - 53 ES - 71

- 2 -

• PLEASE ACTIVATE THE VALVE BEFORE USE IF YOU ARE USING IT FOR THE
FIRST TIME OR AFTER A PERIOD OF IDLENESS TO ENSURE YOU CAN USE IT
PROPERLY: PRESS AND HOLD THE OK BUTTON FOR 5S THEN RELEASE IT
AND REPEAT 3-5 TIMES. (EXPLANATION: IN MOST CASES THE VALVE IS
ACTIVATED, BUT DUE TO EXTERNAL FORCES OR THE ENVIRONMENT DURING
STORAGE AND TRANSPORTATION BY A VARIETY OFFACTORS, THE VALVE MAY
APPEAR TO CLOSE ON ITS OWN, THEN IT NEEDS TO BE ACTIVATED MANUALLY)
• ONLY USE WITH CLEAN WATER (3℃-50℃ ).
• FILTER TRAPS DIRT PARTICLES PROLONGING THE LIFE OF THE PRODUCT.
CLEAN FILTER REGULARLY AND REPLACE IF WORN.
• WHEN EXPECTING FREEZING TEMPERATURES, TIMERS SHOULD BE
REMOVED FROM THE HOSE FAUCET AND STORED INDOORS TO AVOID
POTENTIAL FREEZE DAMAGE.
• THE PRODUCT ITSELF DOES NOT GENERATE PRESSURE, BUT THE PRESSURE
OF TAP WATER IS USED; TAP WATER OR A PRESSURIZED WATER SOURCE
ENSURES A NOMAL EFFLUENT FROM THE IRRIGATION TIMER.
• FOR ANY PROBLEMS DURING USE, PLEASE GET SUPPORT AS FOLLOWS:
- 3 -
IMPORTANT!
PLEASE READ!
WEB: www.rainpointus.com
EMAIL:[email protected]
FREE HOTLINE (US): 833 3815659
EN

DIAL—Rotate the dial to set your watering schedule and confirm the change.
PRODUCT OVERVIEW
At A GLANCE
OK BUTTON—Press to confirm or cancel time and system setup.
+ BUTTON —Press to adjust time and system setup.
LCD SCREEN
Every _ Days
Next
Start Time
P1/P2/P3
Low battery indicator
Flashing during watering
The selected day of the week
Interval watering days
The time left to the next watering
The start time of watering
Watering plans for one day
- 4 -
FILTER
HOSE TAP
CONNECTION
OK
BUTTON
OUTLET
BIG LCD
SCREEN
+ BUTTON DIAL
EN

Waterproof
Min/Max Operating Pressure
Max Flow Rate
Working Temperature
Power By
Thread
0.5bar-8bar (7.25 psi-116 psi)
10 Gal/Min (35L/Min)
3℃-50℃ 37.4℉-122.4℉
IP54
2 AA (1.5V) alkaline batteries (not included)
Watering Times Per Day 1 to 3 times a day (Up to 3 watering plans a day)
Watering Days Monday to Sunday OR Every 2/3/4/5/6 days
NH(US) for 3/4" faucet / hose
BSP(EU) for 3/4" or 1" faucet / hose
SET CLOCK
START TIME
HOW LONG
HOW OFTEN
VIEW SET
ON
Set your local current time
Set the start watering time (Every
watering plan has its own start time)
Set watering duration from 1 minute
to 3 hours 59 minutes.(Every watering
plan has its own watering duration)
Set watering frequency of the week
or every few days (3 watering plans
share 1 watering frequency)
View all your settings of 3 plans
Start automatic watering based on
your programs.
OFF Turn off all watering programs and
shut off the valve.
DIAL POSITION FUNCTION
SPECIFICATION
- 5 -
Watering Duration From 1 minute to 3 hours 59 minutes (4 hours)
Manual Watering Time 1 minute to 8 hours, default 10 minutes
EN

PRODUCT INSTALLATION
INSTALLING THE BATTERIES
1) Remove the battery compartment on back of the timer.
2) Install 2 new AA (1.5V) alkaline batteries (not included).
3) Firmly reinstall the battery compartment back into the timer.
BATTERY STATUS
Battery Status will be displayed as following: Full Low Power
Note:
Firmly restore the battery compartment to ensure
water resistance.
Removed old batteries at the end of the watering
season and disposed of them properly.
Used or dead batteries must be removed from the
timer and disposed of them properly.
Do not dispose of batteries in fire. Batteries may
explode or leak.
Replace batteries when the low battery indicator
appears on displayer. After you done it, please
remember to reset your watering plans.
Note:
When the low battery indicator appears on display, the valve will close automatically to
avoid leakage. Please replace the battery in time in case of interrupting the normal
operation.
- 6 -
EN

- 7 -
1) Attach the timer inlet to the outdoor faucet
( hand tighten only). From the timer outlet
connect a drip irrigation system or a garden
hose.
2) Please turn on the tap after programming
the timer.
Note:
• When programming the timer, please turn off the tap to avoid getting wet.
• Install the timer without any tools.Hand tighten only .
• Protect it from freezing. Timer should be removed to avoid freezing damage.
• Keeping the filter dean and in place when using the timer can prolong it’s life.
INSTALLING THE TIMER
Inlet
Outlet
EN

PROGRAMMING YOUR TIMER
SET CLOCK
STEP 1:
1) Turn dial to SET CLOCK.
2) Hold the "OK" button to switch time display of 12H or 24H mode.
12H mode: with "AM"and "PM"
24H mode: without "AM"and "PM"
3) ""flash: Using the "+" button to set the day of a week and press "OK" to confirm.
4) "00: "flash: Using the "+" button to set hour and press "OK" to confirm.
5) ":00 "flash: Using the "+" button to set minute and turn dial to save changes.
Tips:
Hold the "+" button can increase the time quickly.
At the end of setting, please turn dial to save changes. If you press "OK"at the
end, it will go back to the first setting.
- 8 -
EN

1) Turn the dial to START TIME.
2) Using the"+" button to set the start time and press "OK" to confirm.
3) After confirm the previous plan, press "OK" again to switch to the next plan.
4) Turn dial to confirm the changes.
5) To turn off the start time of certain plan, please press the button when setting that
plan to set the start time to "24 : xx" (24H mode) or"12: xx"PM(12H mode). Meanwhile,
a flashing "OFF" will appear on the screen. Then, press "OK" to confirm turning off
that plan.
Tips:
Hold the "+" button can increase the time quickly.
If you want to reactivate the "OFF"plan, please press the "+" button again at
that plan to set its start time.
At the end of setting, please turn dial to save changes. If you press "OK" at the
end, it will go back to the first setting.
- 9 -
START TIME
STEP 2:
EN

HOW LONG
STEP 3:
1) Turn the dial to HOW LONG. ( will display on the screen)
2) Using the"+" button to set the watering duration, press "OK" to confirm. (Watering
Duration: 0 hour 01minute to 3 hour 59 minutes)
3) After confirming the previous plan, press “OK” again to turn to set the next plan.
4) Turn dial to confirm the changes.
5) To turn off the watering duration of a certain plan, please press the "+"button at that
plan to set the duration to "0 H 59M". Meanwhile, a flashing "OFF" will appear on
the screen. Then, press "OK" to confirm turn off that plan.
Tips:
- 10 -
Hold the"+" button to increase the time quickly.
If you want to reactivate the "OFF" plan, please press the "+" button at that plan to set
its start time again.
At the end of setting, please turn dial to save changes. If you press "OK" at the end, it
will go back to the first seting.
EN

- 11 -
HOW OFTEN
STEP 4:
EN

- 12 -
VIEW SET
STEP 5:
1) Turn the dial to VIEW SET.
2) Press "OK" button to check the START TIME, HOW LONG and HOW OFTEN
settings of the 3 watering plans.
(The start time of P1) (The watering duration of P1) (Watering frequency)
EN

Note:
There is no watering plans being set, which means the start time or watering
duration of all 3 watering plans are truned off.
To turn off a certain plan, please turn off the start time or watering duration of that plan.
(About how to turn off the start time or watering duration, please refer to the section
[STEP 2: START TIME] and [STEP 3: HOW LONG] of Chapter [PROGRAMMING
YOUR TIMER])
- 13 -
AUTO WATERING
STEP 6:
1) Turn the dial to ON.
(All watering plans being set will run automatically)
2) During watering:
a. Display the remaining watering time and will flash.
b. Press the "+" button, and then the current day and time will be displayed.
3) When not watering:
a. If there is no watering plans being set, it will only display the current day and time.
b. If there are plans being set but not running yet, it will display the current day
and time, and followed by how much time is left to the next watering plan.
EN

Note:
ADDITIONAL FEATURES
MANUAL/HAND WATER
This feature allows you to water without interrupting
your set watering schedule.
Please follow the steps below to start manual watering.
1) While the dial is in the "ON" position and hold the "OK" button to start watering manually.
The duration of manual watering is default to 10 minutes.
2) 2 ways to stop manual watering:
a.Hold the "OK" button again;
Or
b.Turn the dial to "OFF" and then back to "ON".
There will be a slight delay between the time the "OK" button is pressed and when
watering begins.
- 14 -
EN

- 15 -
OFF MODE
1) If you wish to stop all 3 watering plans for an extended period, turn the dial to OFF.
(Your settings will be saved)
2) The timer will not run automatically while in OFF mode.
(The screen will display OFF )
3) To start watering again, turn the dial back to ON to resume your programmed watering
schedule.
EN

The water inlet leakage 1. No filter or not be placed
horizontally
2. The faucet is not the
standard 3/4"
1. Air condenses inside the
screen due to the
difference in temperature
between inside and
outside
1. Mixed use of old and new
batteries
2. Used the carbon batteries
or rechargeable batterie
1. Filter blockage
2. Inlet pressure is not
sufficient to support
watering needs.
1. Check if the filter is
clogged, if so, clean or
replace the filter.
2. Make sure the timer is
installed properly and not
cross-threaded.
3. Install a booster pump or
other booster pressurizing
equipment.
1. Use new alkaline batteries.
2. Rechargeable batteries
and carbon batteries have
a short life, use the
alkaline batteries instead
of them.
1. The fog will disappear as
the temperature rises, or
leave it stand for a period
of time.
1. Add filter and make sure
it's placed horizontally in
the inlet.
2. Make sure the faucet is a
3/4" faucet.
3. Strengthen it with raw
rubber wrap.
Short battery life
Condensation on the
screen
Low water pressure
PROBLEM Possible Cause Possible Solution
TROUBLESHOOTING
If your Rainpoint product does not operate properly after trying the troubleshooting
steps, please contact us by phone or email : 1-833-3815659 | [email protected]
- 16 -
EN

WARNINGS
1) For outdoor use ONLY.
2) Clean the filter regulariy and replace if it is worn in order to extend the working life
of timer.
WARRANTY
CUSTOMER SERVICE
3) Do not use water over 120°F (50℃)，or less than 38℉(3℃).
4) In winter, please remove batteries, drain and store it indoor to away from freezing.
5) No need to use tools to install it. Hand tighten ONLY. It may cause some damage for
the timer under other tools.
6) Do not subject the product to extreme force and shock.
7) Severe electrical shock could result if water is sprayed into outlets or sources of
electrical current. Never immerse the product into water.
Rainpoint provides a 1-year limited warranty for this product against manufacturing
defects in materials and workmanship.
1) Warranty service can only be performed by our authorized service center. The
original dated bill of sale must be presented upon request as proof of purchase to us,
or our authorized service center.
2) To receive warranty service, the purchaser must contact with Rainpoint nominated
service center for the problem determination and service procedure.
Thank you for your choice of Rainpoint products!
If you find it difficult to set up and want to watch the setting tutorial videos, welcome to
visit and subscribe our channel on YouTube by searching Rainpoint.
If you can’t find what you need in this user manual, or you need other help of the product,
please check the LOT NO. of your device and contact us before returning the Rainpoint
products to the store.
1-833-3815659 | [email protected]
LOT NO.: xxxxxx (On the back of the timer)
- 17 -
EN

- 18 -
Need Help? Call 1-833 3815659
Or email to [email protected]
Scan the QR code to
vist the setup video
EN

BENUTZERHANDBUCH
ITV101P
Digitale Wasserhahn-Zeitschaltuhr mit 3
Bewässerungsplänen
- 19 -

DIAL—Drehen Sie den Drehknopf, um Ihren Bewässerungsplan einzustellen und
die Änderung zu bestätigen.
PRODUKTÜBERSICHT
Auf einen Blick
OK BUTTON—Drücken Sie , um die Zeit- und Systemeinstellung zu bestätigen
oder abzubrechen.
+ BUTTON—Drücken Sie , um die Zeit- und Systemeinstellungen anzupassen.
- 20 -
FILTER
HOSE TAP
CONNECTION
OK
BUTTON
OUTLET
BIG LCD
SCREEN
+ BUTTON DIAL
DE