RainPoint ITV205 User manual

English Deutsch
WEB: www.rainpointus.com
Email:[email protected]
Free Hotline (US): 833 3815659

PLEASE ACTIVATE THE VALVE BEFORE USE IF YOU ARE USING IT
FOR THE FIRST TIME OR AFTER A PERIOD OF IDLENESS TO
ENSURE YOU CAN USE IT PROPERLY：
1. TURN THE TIMER DIAL TO ON AND HOLD THE OK BUTTON FOR
3-5 SEC TO ENTER MANUAL WATERING MODE.
2. RE-PRESS THE ZONE BUTTON 2 TIMES TO SELECT 2 ZONES
3. AFTER HEARING 2 "CLICKING" SOUND, TURN THE DIAL TO OFF
TO CLOSE THE MANUAL FUNCTION.
4. REPEAT STEPS1-3 FOR 3-5 TIMES.
(EXPLANATION: IN MOST CASES THE VALVE IS ACTIVATED, BUT
DUE TO EXTERNAL FORCES OR THE ENVIRONMENT DURING
STORAGE AND TRANSPORTATION BY A VARIETY OF FACTORS,
THE VALVE MAY APPEAR TO CLOSE ON ITS OWN, THEN IT
NEEDS TO BE ACTIVATED MANUALLY)
FOR ANY PROBLEMS DURING USE, PLEASE GET SUPPORT AS
FOLLOWS：
WEB: www.rainpointus.com
EMAIL:[email protected]
FREE HOTLINE (US): 833 3815659

FILTER
DIAL
DELAY/+
BUTTON
ZONE 2
ZONE
ZONE 1
- BUTTON
OK/MANUAL
BUTTON
HOSE TAP
CONNECTION
BIG LCD
SCREEN
DIAL
OK / MANUAL Button
DELAY / + Button
- Button
ZONE Button

NH (US) for 3/4" taps
BSP (EU) for 3/4" or 1" taps


on the
Insert

1) First select ZONE 1, complete the settings for ZONE 1 according to steps
1-4 below, then turn the dial to "ON" to save the changes.
2) Then press ZONE to select ZONE 2, repeat the following steps 2-4 again,
and finally turn the dial to "ON" to save the changes.

Examples of watering frequencies are every 1 day, every 2 days and
every 3 days：
EVERY 1 DAY
WEEK
ONE
Mon Tue
EVERY 2 DAY
WEEK
ONE
EVERY 3 DAY
WEEK
ONE
Mon Tue
Mon Tue
Wed Thu
Wed Thu
Wed Thu
Fri Sat Sun
Fri Sat Sun
Fri Sat Sun

1) With the dial in the "ON" position, press the "DELAY/+" button for 3-5s to
start the delay watering function.
2) In Delay Mode, you can find the selection of 24H flashing on the screen.
Press "+" and "-" to select delay time from 24H, 48H and 72H.
3) Press "OK" button to confirm, then the screen will flash between clock and
hours remaining before programmed cycle resumes.
4)To remove rain delay,hold the"DELAY/+"button for 3-5s again to resume
your programmed watering schedule.
When the selection is flashing, if there is no action or operation for 5 sec, the
Delay Mode will be automatically cancelled and back to home page.

Note:
1) When the selection is flashing, if there is no action or operation for 5 sec, the
Manual Mode will be automatically cancelled and back to home page.
2) There may be a slight delay between the time the manual button is pressed
and when watering begins.
4) Press "OK"button to confirm and start the manual watering.the screen will
flash between clock and hours remaining before programmed cycle resumes.
5) To stop manual watering, turn the dial to OFFand then back to NO, or hold
the "OK/MANUAL" button for 3-5s again to resume your programmed
watering schedule.
3) Use the "+" and "-" button to select watering time, from 1 min to 8 hours.
(The default watering plan is 10 minutes.)


If you want to use only ZONE 1 and close ZONE
2, please set it up as follows.
1) Turn the dial to "Start Time" and select ZONE 2.
2) Press the "+" or "-" button until the screen
displays OFF.
3) Turn the dial to "ON" to save the changes.
If you only want to use ZONE 2 and close ZONE 1, the same applies.

1. No filter or not be
placed horizontally
2. The faucet is not the
standard 3/4"
The water inlet
leakage
Problem Possible Cause
1. Add filter and make sure
it' s placed horizontally in
the inlet.
2. Make sure the faucet is
a 3/4" faucet.
3. Strengthen it with raw
rubber wrap.
1. Long-term storage and
transportation make the
valve inactive
2. Valve blockage
The water won't
stop/flow out
Step1. Keep the tap turned
off and turn the timer dial to
ON;
Step2. Select the zone you
want to fix (ZONE1 or
ZONE2) and run manual
watering for 3-5s and stop it ;
Step3. Repeat the Step 2 for
5 to 7 times;
Step4. Try using it normally.
Possible Solution
1. The dial/valve is stuck
1. Mixed use of old and
new batteries
2. Used the carbon
batteries or rechargeable
batteries
Dial or button
problems
Short battery life
1.Same procedure as above.
2.Turn the dial to the OFF to
check if the valve can be
closed.
1. Use brand new alkaline
batteries.
2. Rechargeable batteries
and carbon batteries
have a short and unstable
battery life, please use the
alkaline batteries instead
of them.

2. Accidentally holding the
OK button while inserts
the batteries

1. Filter blockage
2. Inlet pressure not
sufficient to support
watering
Low water
pressure
1. Check if the filter is
clogged, if so, clean or
replace the filter.
2. Make sure the timer is
installed properly and not
cross-threaded.
3. Installation of a booster
pump or other auxiliary
equipment of increasing
pressure, the product itself
does not have a
pressurization function.
If you have further questions, visit the following link：
https://rainpointus.com/downloads/faq
If it doesn't work and you want to return or replace it, please contact
us for support during the warranty period.
Hotline (US):1-833-381-5659
E-mail: [email protected]

1) Intended for outdoor use only, put in the sheltered outdoor will prolong the the
product lifetime.
2) Using tools to tighten your timer is too tight, easy to damage. to avoid
damaging the timer, please tighten it with your hand instead of a tool.
3) Please ensure that the filter is placed horizontally in the top connector before
installation to prevent leakage, add a filter and thread seal tape if necessary.
4) Mesh filter prevents dirt particles, prolonging the life of the hose timer. Clean
filter regularly and replace if worn.
5) When the power is low, please replace the batteries in time to avoid the
interruption of the normal operation; when replacing the batteries, please make
sure that the battery compartment is dry.
6) When not in use, remove batteries, drain and store indoors to away from
freezing.
7) Do not use the timer which it's more than 120°F(50℃), or less than 38°F(3℃).
8) Do not subject the product to extreme force and shock.
9) Severe electrical shock could result if water is sprayed into outlets or sources
of electrical current. Never immerse the product in water.

Need Help? Call 1-833 3815659
Or email to [email protected]
Scan the QR code to
vist the setup video

English Deutsch
BENUTZERHANDBUCH
WEB: www.rainpointus.com
Email:[email protected]
Free Hotline (US): 833 3815659

BITTE AKTIVIEREN SIE DAS VENTIL VOR DER BENUTZUNG, WENN
SIE ES ZUM ERSTEN MAL ODER NACH EINER GEWISSEN ZEIT DES
NICHTGEBRAUCHS VERWENDEN, UM SICHERZUSTELLEN, DASS
SIE ES RICHTIG BENUTZEN KÖNNEN：
1. DREHEN SIE DEN TIMER-DREHSCHALTER AUF ON UND HALTEN
SIE DIE OK-TASTE FÜR 3-5 SEKUNDEN GEDRÜCKT, UM IN DEN
MANUELLEN BEWÄSSERUNGSMODUS ZU GELANGEN.
2. DRÜCKEN SIE DIE ZONENTASTE 2 MAL, UM 2 ZONEN
AUSZUWÄHLEN.
3. WENN SIE EIN "KLICKEN" HÖREN, DREHEN SIE DAS RAD AUF
"AUS", UM DIE MANUELLE FUNKTION ZU BEENDEN.
4. WIEDERHOLEN SIE DIE SCHRITTE 1-3BIS 3-5MAL.
(EXPLANATION: IN MOST CASES THE VALVE IS ACTIVATED, BUT
DUE TO EXTERNAL FORCES OR THE ENVIRONMENT DURING
STORAGE AND TRANSPORTATION BY A VARIETY OF FACTORS,
THE VALVE MAY APPEAR TO CLOSE ON ITS OWN, THEN IT
NEEDS TO BE ACTIVATED MANUALLY)
NUR MIT SAUBEREM, KALTEM WASSER VERWENDEN
DER FILTER HÄLT SCHMUTZPARTIKEL ZURÜCK UND VERLÄNGERT
SO DIE LEBENSDAUER DES PRODUKTS. REINIGEN SIE DEN FILTER
REGELMÄSSIG UND ERSETZEN SIE IHN, WENN ER ABGENUTZT IST.
BEI ZU ERWARTENDEN MINUSTEMPERATUREN SOLLTEN
ZEITSCHALTUHREN VOM SCHLAUCHHAHN ABGENOMMEN UND IN
EINEM INNENRAUM GELAGERT WERDEN, UM MÖGLICHE
FROSTSCHÄDEN ZU VERMEIDEN.
BEI PROBLEMEN WÄHREND DER NUTZUNG ERHALTEN SIE
UNTERSTÜTZUNG WIE FOLGT：
WEB: www.rainpointus.com
E-MAIL:[email protected]
KOSTENLOSE HOTLINE (US): 833 3815659

FILTER
DIAL
DELAY/+
BUTTON
ZONE 2
ZONE
ZONE 1
- BUTTON
OK/MANUAL
BUTTON
HOSE TAP
CONNECTION
BIG LCD
SCREEN
Drehen, um Ihren Bewässerungszeitplan anzupassen
Setup bestätigen oder Wasser manuell
Zeit und Systemeinstellung einstellen oder
Bewässerungsprogramm verzögern
Timer und Systemeinstellung einstellen
Taste, um die Zone auszuwählen, die Sie programmieren
möchten
 
Einstellen der aktuellen Uhrzeit
Wählen Sie aus, zu welcher
Zeit die einzelnen Zonen
beginnen sollen
Bestimmen Sie, wie lange Sie
jede Zone bewässern
 

DIAL
OK / MANUAL Button
DELAY / + Button
- Button
ZONE Button

Wählen Sie, wie oft Sie jede
Zone bewässern werden
Timer-Wasser nach Ihrem
individuellen Zeitplan für beide
Zonen
Alle Bewässerungen
abschalten
Alle 1 -12 Stunden oder alle 1-7 Tage
Von 1 Minute bis 3 Stunden 59 Minuten
(4 Stunden)
2 AAA-Alkalibatterien (nicht im Lieferumfang
enthalten)
12H oder 24H
NH (US) für 3/4"-Hähne
BSP (EU) für 3/4"- oder 1"-Hähne
ON
AUS
Min/Max Betriebsdruck
Maximale Durchflussrate
Wasserdichte Rate
Arbeitstemperatur
Betriebsspannung
Bewässerungshäufigkeit
Dauer der Bewässerung
Einlass-/Auslassgewinde
Zeitformat
Leistung durch
