RainPoint TTV102B User manual

USER MANUAL
English Español
Email: se[e-mail]
WhatsApp: [phone]
US: 1-833-381-5659 (EN)
EU: [phone] (EN DE)
Model: TTV102B+TWG009BW

WARM TIPS PLEASE READ
BEFORE USING
Don’t use the water timer when the temperature is
below 37°F(3°C), and please store the timer indoors
to avoid potential freezing damage.
The lter traps di paicles, preventing them from
entering the timer and causing clogging. Please clean
the lter regularly and replace it if worn.
To ensure a longer lifespan, please use 3 new AAA alkaline
batteries (not included). Don’t mix new and old alkaline,
standard (carbon-zinc), or rechargeable batteries.
Only use with clean cold water.
Please activate the water timer before rst use or after a
period of inactivity (Refer to page 6: ACTIVATE THE TIMER
BEFORE USE).
FORANY PROBLEMS DURING USE, PLEASE GET
SUPPORT FROM US:
Web: www.rainpointonline.com
Email: se[email protected]
WhatsApp: [phone]
US Free Hotline(English):
[phone](MON-FRI 9:30 AM-5:30 PM PST)
UK Free Hotline(English Deutsch):
[phone](MON-FRI 9:00 AM-5:00 PM CET)

CONTENTS
INTRODUCTION
CONTENTS IN THE BOX
PRODUCT OVERVIEW
PRODUCE SPECIFICATIONS
INSTALLATION
1. INSTALL APP ON YOUR PHONE
2. PAIR THE IRRIGATION GATEWAY
3. CONNECT THE BLUETOOTH IRRIGATION TIMER
4. ADD BLUETOOTH IRRIGATION TIMER TO
IRRIGATIONGATEWAY
5. INSTALL THE BLUETOOTH WATER TIMER
6. TEST BEFORE USE
APP PROGRAMMING
APP HOME SCREEN
BLUETOOTH IRRIGATION TIMER
Manual Watering
Manual Irrigation Duration
Manual Rain Delay
How to set the Normal Schedule ？
How to set the Cycle&Soak Schedule ？
SMART AUTOMATION
Automation & Tap-to-Run
Steps To Set Automation Or Tap-To-Run
Home Management
RESET THE DEVICE
TROUBLE SHOOTING
WARNINGS & WARRANTY
FCC NOTICE
CUSTOMER SERVICE
01
01
01
01
02
02
02-05
06-07
08
09
10
11
11
12-13
14
15
16
17
17
18
18
19
20
21
22-24
24
25
26

ABCD
INTRODUCTION
CONTENTS IN THE BOX
A. 1 x TTV102B 1 Zone
Bluetooth Irrigation Timer
B. 1 x TWG009BW
Irrigation Gateway
C. 1 x Instruction Manual
D. 1 x Quick Setup Guide
TWG009BW Irrigation Gateway
TTV102BBluetooth Irrigation Timer
Product Oveiew
Min/Max Operating Pressure 0.5bar-8bar (7.25 psi-116.03 psi)
10 Gal/Min (35L/Min)
IP54
Max Flow Rate
Waterproof Rate
37.4℉-122℉(3℃-50℃)
3 AAA (1.5V) alkaline batteries(Excluded)
NH (US) for 3/4"taps
BSP(EU) for 3/4" or 1"taps
Working Temperature
Thread
Power By
Inlet
Outlet
Button Button
LED Indicator
Light
PRODUCE SPECIFICATIONS
- 01 -

INSTALLATION
1. INSTALL APP ON YOUR PHONE
Rainpoint
2. PAIR THE IRRIGATION GATEWAY
1. Plug your Irrigation Gateway to an indoor power source near your WiFi
router and the outdoor location of your timer
2. Open the RainPoint App and tap ''Add device ''or ''＋'' to add a new device.
3. Tap ''Sma Irrigation'' and ''Add Manually''.then select
''Irrigation Gateway ''
1 Download the RainPoint App Search for ''RainPoint'' on Google Play
or App Store or scan the QR code to download the RainPoint APP.
2 Register your RainPoint account Open your RainPoint APP, select Set
Up Follow the prompts to register a RainPoint account withyour
email or mobile number.
- 02 -

4. Plug the TWG009BW Irrigation Gateway into an outlet near the router
and wait 10 seconds for the device initialization to complete.
Press and hold for 5 seconds until the blue indicator light is always on
and the red indicator light is blinking slowly, Then the APP will search
and pair your Irrigation Gateway automatically.
- 03 -

5. Select 2.4Ghz WiFi, and enter the password
Tips: If your router is a dual-band router, and you cannot identify the
2.4Ghz or 5Ghz WiFi, please tap the blue words Common router setting
method to name the 2.4Ghz WiFi dierently, then you can select it
individually.
If you encounter problems during the connection process, please search
@RainPoint on Youtube to watch the operation video, or contact us at
se[e-mail].
- 04 -

6. After the connection is successful, the color icon of Irrigation Gateway
will be displayed on the APP home screen.
- 05 -

3. CONNECT THE BLUETOOTH IRRIGATION TIMER
1. Inse 3 *AAA alkaline batteries into the batte tray of the timer.
Restore the batte tray and make ceain it is secured.
2. Return to the APP home screen, and tap " ＋ "to add the WiFi timer
3. Tap "Sma Irrigation" and " Add Manually " , then select
" Bluetooth Irrigation Timer "
- 06 -

4. Press and hold the button on the timer until the Blue LED indicator
blink rapidly (2 times per second). Then select "conrm indicator
rapidly blink"and tap Next.
The APP will search and pair your Bluetooth Water Timer automatically.
5. Click " +" on the right side of the device to add the device, and then
click "Done" for nal conrmation after the device is successfully added.
Note:Before adding the water timer, please turn on the Bluetooth for
pairing, and turn o the Bluetooth after the pairing is successful. In
addition, please pay attention to the distance when connecting with
Bluetooth. We recommend that you connect within 1 meter of the
water timer for faster pairing.
- 07 -

4. ADD BLUETOOTH IRRIGATION TIMER TO
IRRIGATION GATEWAY
1: Go to the home page and
click on the gateway
2: Click on Add Device
4: Select the timer and conrm 3: Select Add existing
When you add the timer
to the Irrigation Gateway
it becomes a remote
controllable timer
- 08 -

5. INSTALL THE BLUETOOTH WATER TIMER
1) Turn o the garden faucet.
2) Wrap Teon Tape around the faucet threads.
3) Screw the timer to the garden faucet and make the display is as veical
as possibleto the ground to prevent rainwater from accumulating and
leaking into the interior.
4) Wrap Teon Tape around the threads of the timer outlets.
5) Screw the garden hoses to the timer outlets.
6) Turn on the faucet after programming the timer.
Tips: If the connection between the timer and the faucet or hose is not
tight or leaking, wrap more Teon Tape(thread seal tape) to make them tight.
Outlet
Inlet
Less than 160 feets
(No bushes, walls blocking)
Please install the lter properly and keep it clean as follows.
Warning
* Please make sure the sma phone is near the Bluetooth water timer
when connecting orsetting the watering plan. The best range for
connection and operation is within 60 meters in the open area. If there
are walls iron gates or bushes blocking, please shoen the distance
betweenthem to better receive the signal.
Please install the lter correctly to achieve better ltering eect.
- 09 -

6. TEST BEFORE USE
Note:
When testing, please keep away from the water outlet of the timer to
avoid being splashed and wet.
Congratulations, you have completed the
connectionand installation of the Bluetooth
Irrigation Timer. Please test whether the internal
valve of your water timer is normal before using it.
1. Keep the faucet turned o.
2. Press the button of the timer , with a "click"
sound,the valve inside the timer opens for
manual watering. After a few seconds,press
the button again, the "click" will sound again,
and the valve will close.
3. Turn on the faucet a little bit, press the button
of the timer to check if the water ow out or
shut o as expected. If yes, the valve is normall,
please use it with condence! If not,
please repeat the above steps several times.
The test is over, evething is normal, please
keep the faucet fully turned on!
Explanation: The valve is activated usually, but due to various factors
such as external force or the environment during storage and transpor-
tation, the valve may be protectively closed. In this case, you need to
activate the timer manual.
- 10 -

APP PROGRAMMING
APP HOME SCREEN
Add Devices
You can add multiple
RainPoint devices on
the APP to create a
sma home irrigation
system.
Room Management
Room Management
is for indoor automatic
irrigation system in
dierent room.
Me
On the Me screen,
there is Message
Centerand FAQ &
Feedback functions.
You will receive water
leak and low batte
ales on Message
Center. And you can
get FAQ and repo
issue on FAQ &
Feedback.
Local Weather Forecast
Get your local
weathe forecast from
website to realize
intelligent watering.
All Devices
A check list of all the
devices you have
connected. Tap to
enter the operation
page of devices you
have added to
program the
operation schedule
of the device.
Sma
On the Sma screen,
there is Tap-to-Run
and Automation
functions. You can
automate multiple
sma products by
setting conditions and
tasks.
Home Management
You can locate your
home, customize
the home name and
add family members.
It is convenient for you
to manage irrigation
schedules for
dierent residences.
- 11 -

BLUETOOTH IRRIGATION TIMER
Tap the Bluetooth water timer on the all devices list of APP home screen.
It will display all the parameters and functions of the timer manually set
on the APP.
Note:
The Bluetooth timer will follow and peorm the preset watering schedule
after application set successfully, even if the phone or device loses
network connection. Device Control
Tap on the top right of
the screen, you will enter
the page for device
information.
Batte Status &
Working Status
Display the batte level
of the timer, the current
working mode.
Weather Information
Get your local weather
forecast from website.
Irrigation Time
Manually set the watering
duration of the Bluetooth
timer, it will display the
duration on the screen.
Last Run Time& Next Run Time
The Bluetooth timer for the last watering
time and the next watering time.
- 12 -

Tap the “Device" name on the screen to setup. You can change the
Device prole for device name. You can name your Bluetooth timer if you
have more than one.This helps you identify your timers.
- 13 -

Manual Watering
(Default watering is 10 minutes)
Manual/Hand Watering（3 methods）
Operating Method 1: APP Home Screen
Operating Method 2: Timer Editing Screen
- 14 -

Operating Method 3：Bluetooth Timer
Press and hold the gray button of the
Bluetooth timer, you will hear a "di" sound
that means the valve is open and the blue
light is ashing. Press again to close the valve.
Manual Irrigation Duration
1. Click the Irrigation Duration button to set the desired manual watering
time and click Save.
2. Go to the home page to tap the sta watering bottom.
- 15 -

Manual Rain Delay
Rain delay applies to rainy days. During the rain delay, the timer stops
watering.
After the rain delay ends, the timer will be executed according to the next
watering plan. The timer can set 24/48/72 hours of rain delay.
- 16 -

How to set the Normal Schedule ？
1. Click to enter the setting Normal Schedule.
2. Tap to enter the Normal Schedule.
How to set the Cycle&Soak Schedule ？
1. Click to enter the setting Cycle&Soak Schedule.
2. Select Cycle&Soak watering mode.
- 17 -