RainPoint ITV201P User manual

USER MANUAL
2-Zone Hose Faucet Timer
Model No.ITV201P
WEB: www.rainpointus.com
Email:[e-mail]
Free Hotline (US): 833 3815659

PLEASE ACTIVATE THE VALVE BEFORE USE IF YOU ARE USING IT
FOR THE FIRST TIME OR AFTER A PERIOD OF IDLENESS TO
ENSURE YOU CAN USE IT PROPERLY：
1. TURN THE TIMER DIAL TO ON AND HOLD THE OK BUTTON FOR
3-5 SEC TO ENTER MANUAL WATERING MODE.
2. RE-PRESS THE ZONE BUTTON 2 TIMES TO SELECT 2 ZONES
3. AFTER HEARING 2 "CLICKING" SOUND, TURN THE DIAL TO OFF
TO CLOSE THE MANUAL FUNCTION.
4. REPEAT STEPS1-3 FOR 3-5 TIMES.
(EXPLANATION: IN MOST CASES THE VALVE IS ACTIVATED, BUT
DUE TO EXTERNAL FORCES OR THE ENVIRONMENT DURING
STORAGE AND TRANSPORTATION BY A VARIETY OF FACTORS,
THE VALVE MAY APPEAR TO CLOSE ON ITS OWN, THEN IT
NEEDS TO BE ACTIVATED MANUALLY)
FOR ANY PROBLEMS DURING USE, PLEASE GET SUPPORT AS
FOLLOWS：
WEB: www.rainpointus.com
EMAIL:[e-mail]
FREE HOTLINE (US): 833 3815659

Select Zone Left or Zone Right to be programmed
FILTER
DIAL
DELAY/+
BUTTON
ZONE
BUTTON
- BUTTON
P BUTTON
OK/MANUAL
BUTTON
HOSE TAP
CONNECTION
BIG LCD
SCREEN

3 C - 50 C (37 F - 122 F)
Water Duration 1min - 3h59min
Water Frequency every 2 days to every 6 days or any
day from Monday to Sunday
Waterproof and Dustproof IP54
Max Flow Rate 35L/Min
Thread Type For tap 3/4 or 1 with BSP or NH thread
Powered By 2*AAA Alkaline Batteries (Excluded)
Battery Life Approx 1 year
Working Temperature
Operating Water Pressure 0.5 - 8bar (7-116 psi)

1) First select ZONE L, complete the settings for ZONE L according to steps
1-4 below, then turn the dial to "ON" to save the changes.
2) Then press ZONE to select ZONE R, repeat the following steps 2-4 again,
and finally turn the dial to "ON" to save the changes.
After completing the settings of each dial item, please turn the dial to save
and go to the nextdial item. If you continue to press the OK button at this
time, you will re-enter the setting of the dial item.

1. Turn dial to START TIME.
2. Using the "+"and "-"button to set time to start watering.
3. Using "OK"button to switch time between hours and minutes.
4. Press "P"to switch plan between P1, P2 and P3.
5. Press "ZONE"button to switch outlet betweenZONE Left andZONE Right .
6. Turn dial to save changes.
1. Turn dial to HOW LONG.
2. Using the "+"and "-"button to set the time of watering duration from 1 minute to
3 hours 59 minutes.
3. Using "OK"button to switch time between hours and minutes.
4. Press "P"to switch plan between P1, P2 and P3.
5. Press "ZONE"button to switch outlet betweenZONE Left andZONE Right .
6. Turn dial to save changes.

1.Turn the dial to HOW OFTEN.
2.There are 2 setting modes for watering frequency.
1）Weekday Mode : Monday toSunday.
(Watering plans will run every Sunday, Wednesday, Thursday and Friday)
a. Press "+" button to select the day of the week, press "OK" toconfirm.
b. means the "Day" has been selected. Pressing "OK" again can cancel the
selection.
c. Turn dial toconfirm the changes.
(Watering plans will run every day)
If you want to run the watering schedule every day, please select every day from
Monday toSunday.
After you have finally selected the days to be watered, please do not press the
OK button toconfirm, please turn the dial directly to confirm. Otherwise the
cursor will flashing on next day or enter the “Every 2/3/4/5/6 Days Mode”

2）Every 2/3/4/5/6 Days Mode: (Without Every 1 Day Mode)

If there are no problems, please turn dial toONto allow your timer to water according
tothe programmed time, zone, duration and frequency.
1) With the dial in the "ON" position, press the "DELAY/+" button for 3-5s to
start the delay watering function.
2) In Delay Mode, you can find the selection of 24H flashing on the screen.
Press "+" and "-" to select delay time from 24H, 48H and 72H.
3) Press "OK" button to confirm, then the screen will start countdown. The plan will
resume when the countdown ends.
4) To remove rain delay, you need to hold the “DELAY/+” button for 3-5s again to
resume your watering schedules.
When the selection is flashing, if there is no action or operation for 5 sec, the
Rain Delay Mode will automatically start based on the time you stay.

1) When the selection is flashing, if there is no action or operation for 5 sec, the
Manual Mode will automatically start based on the time you stay.
2) There may be a slight delay between the time the manual button is pressed
and when watering begins.
4) Press "OK" button to confirm and start the manual watering.
5) To stop manual watering, turn the dial to OFF and then back to ON, or hold
the "OK/MANUAL" button for 3-5s again to resume your programmed
watering schedule.
3) Use the "+" and "-" button to select watering time, from 1 min to 59 mins.
(The default manual watering time is 10 minutes.)
R
L
LEFT
R
Zone L are shown by default.
RIGHT

If you want to use onlyZONE L and close ZONE
R, please set it up as follows.
1) Turn the dial to "Start Time" and select ZONE R.
2) Press the "P" button to switch Plan, then press
the "+" or "-" button until the screen displays OFF
bonoth P1, P2 and P3.
3) Turn the dial to "ON" to save the changes.
If you only want to useZONE R and close ZONE L, the same applies.
Note: When the low battery indicator appears on display, the valve will close automatically
to avoid leakage. Please replace the battery in time in case of interrupting the normal operation.

1. No filter or not be
placed horizontally
2. The faucet is not the
standard 3/4"
The water inlet
leakage
1. Add filter and make sure
it' s placed horizontally in
the inlet.
2. Make sure the faucet is
a 3/4" faucet.
3. Strengthen it with raw
rubber wrap.
1. Long-term storage and
transportation make the
valve inactive
2. Valve blockage
The water won't
stop/flow out
Step1. Keep the tap turned
off and turn the timer dial to
ON;
Step2. Select the zone you
want to fix (ZONE L or
ZONE R) and run manual
watering for 3-5s and stop it ;
Step3. Repeat the Step 2 for
5 to 7 times;
Step4. Try using it normally.
1. The dial/valve is stuck
1. Mixed use of old and
new batteries
2. Used the carbon
batteries or rechargeable
batteries
Dial or button
problems
Short battery life
1.Same procedure as above.
2.Turn the dial to the OFF to
check if the valve can be
closed.
1. Use brand new alkaline
batteries.
2. Rechargeable batteries
and carbon batteries
have a short and unstable
battery life, please use the
alkaline batteries instead
of them.
2. Accidentally holding the
OK button while inserts
the batteries

1. Filter blockage
2. Inlet pressure not
sufficient to support
watering
Low water
pressure
1. Check if the filter is
clogged, if so, clean or
replace the filter.
2. Make sure the timer is
installed properly and not
cross-threaded.
3. Installation of a booster
pump or other auxiliary
equipment of increasing
pressure, the product itself
does not have a
pressurization function.
If you have further questions, visit the following link：
https://rainpointus.com/downloads/faq
If it doesn't work and you want to return or replace it, please contact
us for support during the warranty period.
Hotline (US):1-833-381-5659
E-mail: [e-mail]

1) Intended for outdoor use only, put in the sheltered outdoor will prolong the the
product lifetime.
2) Using tools to tighten your timer is too tight, easy to damage. to avoid
damaging the timer, please tighten it with your hand instead of a tool.
3) Please ensure that the filter is placed horizontally in the top connector before
installation to prevent leakage, add a filter and thread seal tape if necessary.
4) Mesh filter prevents dirt particles, prolonging the life of the hose timer. Clean
filter regularly and replace if worn.
5) When the power is low, please replace the batteries in time to avoid the
interruption of the normal operation; when replacing the batteries, please make
sure that the battery compartment is dry.
6) When not in use, remove batteries, drain and store indoors to away from
freezing.
7) Do not use the timer which it's more than 120°F(50℃), or less than 38°F(3℃).
8) Do not subject the product to extreme force and shock.
9) Severe electrical shock could result if water is sprayed into outlets or sources
of electrical current. Never immerse the product in water.

Need Help? Call 1-833 3815659
Or email to [e-mail]
Scan the QR code to
visit the setup video