Reison 10-396-K User manual

10-396-K Edit.3 Page 1( 5)
USER´S MANUAL
ARM & HAND OP.TABLE
10-396-K
GMDN 62599
PID 129047

10-396-K Edit.3 Page 2( 5)
INTRODUCTION
The arm & hand operating table is made for positioning and operation of arms and hands. It shall be
hooked on the accessory rail of the operating table. The plate is made of light weight carbon fiber
and is very stiff. The plate also has excellent properties for fluoroscopy examination and due to the
stiff plate the table can be used without supporting leg.
ABOUT USER´S MANUAL
This user´s manual is for clinical personnel, service personnel and others who need the knowledge
about and understanding of how the arm operating table works and how it can be used.
❖Read user´s manual carefully before use of the equipment.
❖Always follow the instructions in user´s manual.
❖Always keep user´s manual close to the equipment.
INSTALLATION
At the unpacking, check for any kind of damage on the equipment. Also check the content against
the delivery note. The packing material consists of cardboard and plastic and can be recycled
according to local regulations.
IMPORTANT SAFETY INSTRUCTIONS
❖When applying the arm operating table to the operating table, the responsible personnel
must be sure of that the both clamps are properly hooked and locked to the accessory rail.
A slight “click” appears when the lock levers are in correct position.
❖When the arm operating table shall be adjusted in height, the responsible personnel must
be sure of that there are no human parts in the risk area between the underside of the plate
and the clamps. To avoid the personnel from getting hands or fingers jammed, the arm
operating table must be supported at the underside when the lock levers for height
adjustment loosens.
❖The arm operating table is designed for a Safe Working Load (SWL) of 15kg. To keep the
safety factor according to the European standards EN 60601-1 and EN 60601-2-46 the
SWL shall not be exceeded. A SWL of 15 kg is corresponding to a patient weight of
200kg.
❖During moving of mobile operating tables, the arm operating table must be removed to
avoid collision with other equipment.
❖A function control must always be done before every use of the equipment.

10-396-K Edit.3 Page 3( 5)
CARE AND MAINTENANCE
CLEANING
Clean with an antiseptic detergent with PH 6-8 and tempered water. Dry with soft
cloth. Alcohol may be used on metal parts. Don’t use detergents containing strong
acids or bases.
CONTROL
Check before every use for damages making the use hazardous. Check the locking
function of the clamps to the accessory rail. Also check the locking of the
height adjustment.
ANNUAL SERVICE
Once a year the arm operating table shall be carefully cleaned. Threads and moving
parts shall be lubricated with water resistant grease. All locking functions shall be
tested and if necessary adjusted for safe locking.
Be aware of that service, all kind of repair and preventing maintenance must always be done by
for this purpose educated personnel and according to issued intervals. Changing of the
construction or part of it without a written permission from the manufacturer is strictly forbidden.
Transgression will be prohibited.
GENERAL DESCRIPTION
The arm & hand surgery table shall be hooked on to the accessory rail of the operating table and
be locked by turning the two lock levers to horizontal position. The turning can be done to the
right or to the left. A slight “click” appears when the locking is correct. Check that the clamps are
correctly hooked to the rear side of the accessory rail.
Adjustment of the height is made by turning the two lock levers for height adjustment one turn
anticlockwise, set desired height and then lock by turning the levers clockwise.
Pad with velcro fixation
Hook on clamps
RISK AREA
Lock levers for
height adjustment.
Lock levers for locking
against accessory rail.

10-396-K Edit.3 Page 4( 5)
CAUTION! When the lock levers are loosened, the plate must be supported to prevent it from
uncontrolled lowering
SPARE PARTS
1. Plate assembly 11947 1pc.
2. Washer BRB 10,5x22x2 A2 2pcs.
3. Post 10968 2pcs.
4. Guide 10053 2pcs.
5. Parallel bar 10966 1pc.
6. Rail fitting 10031 1pc.
7. Washer 10004 2pcs.
8. Screw MF6S M6x12 A2 2pcs.
9. Screw MC6S M6x40 FZB 4pcs.
10. Adjustable lock lever 6-593-65 2pcs.
11. Shaft 10009 2pcs.
12. Spring 10013 2pcs.
13. Pin 10012 2pcs.
14. Plunger 10711 1pc.
15. Eccentric 11165 2pcs.
16. Lock lever 10014 2pcs.
17. Ball K20 M8 S 2pcs.
18. Pad fixation 11364 4pcs.

10-396-K Edit.3 Page 5( 5)
TECHNICAL SPECIFICATIONS
Length 62,5cm
Width 34cm
Height 22cm
Height adjustment 9,5cm
Weight 4,2kg
Safe Working Load 15kg
Max patient weight 200kg
Box 240 Eriksbergsvägen 32A
734 25 Hallstahammar
Sweden
Phone: [phone] Fax: [phone]
E-mail: [email protected]e
www.reison.se