Reison 10-359 User manual

USERS MANUAL
ANGULAR ACCESSORY RAIL
10-359
GMDN 41893
PID 59660
10-359 Edit.1 Page 1(4)

INTRODUCTION
This angular accessory rail is made to extend the normal rail on an operating table. Also, when a
accessory have to be attached laterally or slanted out from the op.table, the angular accessory rail fits
in. It is provided with a quick lock “hook on” clamp. It can be adjusted in height and the rail itself
can be rotated all around and locks every 15°.
ABOUT USERS MANUAL
This user manual is for clinical personnel, service personnel and others who need the knowledge
about and understanding of how this accessory works and how it can be used.
•Read user manual carefully before use of the equipment.
•Always follow the instructions in user manual.
•Always keep user manual close to the equipment.
INSTALLATION
Check by the unpacking, that there are no damages on the equipment and that all parts are delivered
according to the delivery bill. Also, check for loose parts in the box.
The packing material consists of cardboard and plastic which all can be recycled.
IMPORTANT SAFETY INSTRUCTIONS
•When the locking lever for height adjustment is released, responsible personnel must be sure
of that there are no human parts in the risk area and that the accessory is supported in any
other way to prevent it from falling down.
•To avoid damage on the accessory, or on other equipment, all movements with the operating
table must be done very carefully.
•The locking lever in the clamp must not be released when an accessory is attached to the
angular accessory rail, if it isn´t supported in any other way.
GENERAL DESCRIPTION
10-359 Edit.1 Page 2(4)
Lock lever for
vertically adjusting.
To release, turn lever
anticlockwise. To lock
turn lever clockwise.
”Hook on” clamp with
eccentric locking
Clamp lock lever. For locking,
turn lever to horizontal, to the
right or to the left.
Knob for angular adjust of the accessory rail. To
release the rail, turn the knob clockwise 2-3
revolutions, put rail in desired position and lock
by turning the knob anticlockwise.
Accessory rail

MAINTENANCE AND CARE
Be aware of, that service and all kind of repair always must be done by for this purpose educated
personnel. Changing of any part in the construction without a written permission from the
manufacturer is strictly forbidden.
CLEANING
Clean with soap and tempered water. If necessary, use alcohol as supplement. Only use
soft cloth for wiping.
CONTROL
Check every day before use for any kind of damages. Also check the locking functions.
ANNUAL SERVICE
Once a year the angular accessory rail shall be carefully cleaned. All moving parts shall
be greased with thin white grease. The locking functions shall be checked and, if
necessary adjusted.
SPARE PARTS
10-359 Edit.1 Page 3(4)
1. Post weld assembly 10481 1pc.
2. Spring Lesjöfors 1602 1pc.
3. Gear ring 10120 1pc.
4. Rail weld assembly 10477 1pc.
5. Washer 10480 1pc.
6. Washer BRB 10,5x20x2 Nylon 1pc.
7. Knob VC.53 p-M10x30 soft 1pc.
8. Screw MF6S M6x12 A2 1pc.
9. Washer 10004 1pc.
10. Clamp housing 10031 1pc.
11. Spacer 10526-A 1pc.
12. Guide 10053 1pc.
13. Lock lever 6593-65 M10x1x15 1pc.
14. Screw MC6S M6x45 FZ 2pcs.
15. Shaft 10009 1pc.
16. Spring 10013 1pc.
17. Pressure pin 10012 1pc.
18. Plunger 10711 1pc.
19. Eccentric 11165 1pc.
20. Lever 10014 1pc.
21. Ball K20 M8 S 1pc.

TECHNICAL SPECIFICATION
Height 33cm
Width 30cm
Vertical adjustment 16,5cm
Weight 2,2kg
Angel adjustment of rail 360°
Safe Working load 25kg
Box 240 Eriksbergsvägen 32A
734 25 Hallstahammar
Sweden
Phone: [phone] Fax: [phone]
E-mail: [email protected]e
www.reison.se
10-359 Edit.1 Page 4(4)