Sauder 422807 User manual

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-445-1527.
Share your journey!
sauder.com
Night Stand
Beginnings Collection | Model 422807
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-15
Français pg 16-18
Español pg 19-21
Lot #: 527151
Date Purchased: __________________
02/22/19
Be sure to give us a ring before
making any returns. 1-800-445-1527
Sweet stand.
Sweet dreams.

Table of Contents Assembly Tools Required
3
4
5-15
16-18
19-21
22
23
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2 www.sauder.com 422807

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E BACK (1)
F SKIRT (1)
G DRAWER FRONT (1)
H DRAWER SIDE (2)
I DRAWER BACK (1)
J DRAWER BOTTOM (1)
Now you know
our ABCs.
Page 3www.sauder.com422807
A
B
C
D
E
F
G
H
I
J
H

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4 www.sauder.com 422807
HIDDEN CAM - 4
19
APPLIQUE CARD - 1
25 NAIL - 8 26
27 GOLD 2" FLAT HEAD SCREW - 4
WOOD DOWEL - 4
21 ANGLE BRACKET - 3 22
DRAWER FRONT
BRACKET - 2
23 PULL - 1 24
33 BLACK 1" PAN HEAD SCREW - 4
31 GOLD 5/8" FLAT HEAD SCREW - 6 30 SILVER 3/4" PAN HEAD SCREW - 2
32 GOLD 5/16" FLAT HEAD SCREW - 8
28 SILVER 1-1/2" PAN HEAD SCREW - 4
30DA UNIVERSAL
CABINET RAIL - 2
1
0
2
3
30DA
30DC DRAWER RIGHT - 1
DR
DR
AW
AW
ER RIG
ER RIG
HT
HT
2 1
30DC
30DD DRAWER LEFT - 1
DR
DR
AW
AW
ER LEF
ER LEFT21
30DD
CAM SCREW - 4
20

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Insert four HIDDEN CAMS (19) into the ENDS (A and B).
å Fasten the UNIVERSAL CABINET RAILS (30DA) to the
ENDS (A and B). Use four GOLD 5/16" FLAT HEAD
SCREWS (32) through holes #1 and #3.
Page 5www.sauder.com422807
B
Glide end
3
2
1
1
2
3
Glide end
Finished edge
Finished edge
GOLD 5/16" FLAT HEAD SCREW
(4 used for the RAILS)
32
Surface with
more holes
A
Surface with
more holes
30DA
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
19
Arrow
VIEW THE DRAWER GLIDE VIDEO

Step 2
å Turn four CAM SCREWS (20) into the TOP (C).
Page 6 www.sauder.com 422807
Surface with holes
C
20

å Fasten two ANGLE BRACKETS (22) to the SKIRT (F).
Use two GOLD 5/8" FLAT HEAD SCREWS (31).
å Fasten the SKIRT (F) to the BOTTOM (D). Use one
ANGLE BRACKET (22) and two GOLD 5/8" FLAT
HEAD SCREWS (31).
Step 3
Page 7www.sauder.com422807
D
F
GOLD 5/8" FLAT HEAD SCREW
(4 used in this step)
31
Surface with hole
Surface with holes
22
Curved edge
Side Step: Make
nachos. (Optional, but
recommended.)
22
22
F

Step 4
å Fasten the ENDS (A and B) to the TOP (C). Tighten four
HIDDEN CAMS.
Page 8 www.sauder.com 422807
C
A
Surface without
HIDDEN CAMS
B
Surface with
HIDDEN CAMS
Surface with CAM SCREWS
Unfinished edge
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
1
2

å Fasten the BOTTOM (D) to the ENDS (A and B). Use four
GOLD 2" FLAT HEAD SCREWS (27).
å NOTE: Start each SCREW a few turns before completely
tightening any of them.
å Fasten the SKIRT (F) to the ENDS (A and B). Use two
GOLD 5/8" FLAT HEAD SCREWS (31) through the
ANGLE BRACKETS on the SKIRT and into the ENDS.
Step 5
Page 9www.sauder.com422807
A
B
D
F
GOLD 5/8" FLAT HEAD SCREW
(2 used in this step)
31
GOLD 2" FLAT HEAD SCREW
(4 used in this step)
27
27

Step 6
Page 10 www.sauder.com 422807
å Lay the BACK (E) over your unit.
å Make equal margins along the top and side edges of the
BACK (E). Push on opposite corners of your unit if needed
to make it "square".
å Fasten the BACK (E) to your unit using the NAILS (26).
å NOTE: There are no nail holes along the bottom edge of
the BACK.
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NAIL
(8 used in this step)
26
E
There are no nail holes along
the bottom edge of the BACK.