Sauder 411312 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-22
Français pg 23-25
Español pg 26-28
Lot # 387972 01/27/16
Purchased: __________________
Be sure to give us a ring before
making any returns. 1-800-523-3987
Wardrobe/Storage Cabinet
HomePlus Collection | Model 411312
Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.
Prefer the phone? Call 1-800-523-3987.
Share your journey!
sauder.com
Store behind
closed doors.

Table of Contents Assembly Tools Required
2-3
4-5
6-22
23-25
26-28
29-30
31
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
411312 www.sauder.com/servicesPage 2
Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D2 BOTTOM (1)
D50 RIGHT DRAWER SIDE (1)
D51 LEFT DRAWER SIDE (1)
D175 DRAWER BACK (1)
D983 DRAWER BOTTOM (1)
E BACK (1)
F SHELF (1)
H DOOR (2)
I ADJUSTABLE SHELF (1)
J FRONT SKIRT (1)
K SIDE SKIRT (2)
L DRAWER FRONT (1)
M65 DRAWER BRACE (1)
P TOP MOLDING (1)
V V LARGE BALLAST (2)
WW SMALL BALLAST (2)

Part Identification Now you know
our ABCs.
411312www.sauder.com/services Page 3
A
B
C
D2
H
J
F
E
H
I
K
P
D50
D51
D175
D983
L
K
V V
V V
WW
WW
M65

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
411312 www.sauder.com/servicesPage 4
CABINET LEFT - 1
40CB
CABINET RIGHT - 1
40CA
DRAWER RIGHT - 1
40CC
DRAWER LEFT - 1
40CD
ROD - 1
VU
TWIST-LOCK®
FASTENER - 10 ROD HANGER - 2
W
HIDDEN
CAM - 1
1F
AA
SAFETY
BRACKET - 1 DOOR STOP - 1
BB
CAM
SCREW - 1
8F
CC
ADJUSTABLE
GLIDE - 4 PROPEL NUT - 4
DD
FOOT - 2
EE
SIDE
FOOT - 2
FF
LARGE
PULL - 2
GG
PULL - 1
HH
METAL
PIN - 4
LL
RUBBER
SLEEVE - 4
MM
NN WARNING LABEL - 1
(Refer to Step 16 for proper
location and application)
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
• Place heaviest items in the lowest drawers.
• Unless specifically designed to accommodate, do not
set TVs or other heavy objects on top of this product.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
• If equipped with a drawer interlock system, do not
defeat or remove it.
Use of tip-over restraints may only reduce, but not
eliminate, the risk of tip-over.
This is a permanent label. Do not attempt to remove!
04/10 332296
DRAWER FRONT
BRACKET - 1
II
HINGE - 6
Z

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
411312www.sauder.com/services Page 5
BLACK 1-7/8" FLAT HEAD SCREW - 5
OO
BLACK 7/8" MACHINE SCREW - 6
PP
BLACK 9/16" LARGE HEAD SCREW - 7
QQ
BLACK 9/16" WAFER HEAD SCREW - 4
RR
NAIL - 52
UU
BLACK 1/2" FLAT HEAD SCREW - 12
SS
GOLD 5/16" FLAT HEAD SCREW - 8
3S
BLACK 3" PAN HEAD SCREW - 2
84S
30S BLACK 1-9/16" FLAT HEAD SCREW - 5

Step 1 Look for this icon. It means a
video assembly tip is available at
www.sauder.com/services/tips
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å To begin assembly, push a SAUDER TWIST-LOCK®
FASTENER (U) into the large holes in the TOP (C)
and SHELF (F).
411312 www.sauder.com/servicesPage 6
U
U
U
C
F
Do not tighten the TWIST-LOCK® FASTENERS in this step.
Scan this QR code or go to this address:
http://qr.sauder.com/?ID=1378
to watch a video on how to assemble your unit.

å Fasten the CABINET RIGHT (40CA) and CABINET
LEFT (40CB) to the ENDS (A and B). Use four GOLD
5/16" FLAT HEAD SCREWS (3S).
å Fasten the ROD HANGERS (W) to the ENDS (A and B).
Use two BLACK 9/16" LARGE HEAD SCREWS (QQ).
Step 2
411312www.sauder.com/services Page 7
A
B
W
GOLD 5/16" FLAT HEAD SCREW
(4 used for the CABINET RAILS)
3S
BLACK 9/16" LARGE HEAD SCREW
(2 used for the ROD HANGERS)
QQ
Long finished edge
Roller end
Roller end
Long finished edge
Remember:
Righty tighty.
Lefty loosey.

Step 3
å Fasten the LEFT END (B) to the TOP (C) and SHELF (F).
Tighten four TWIST-LOCK® FASTENERS.
411312 www.sauder.com/servicesPage 8
BC
F
Finished surface
Edge with
TWIST-LOCK®
FASTENERS
Unfinished surface
Long finished edge
Finished edge
How to use the SAUDER TWIST-LOCK®FASTENER
1. Insert the dowel end of the FASTENER into the hole of the
adjoining part.
NOTE: The dowel end of the FASTENER must remain fully
inserted in the hole of the adjoining part while locking
the FASTENER.
2. Tighten the FASTENER with a Phillips screwdriver as tight
as possible.
Dowel end
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

å Fasten the RIGHT END (A) to the TOP (C) and SHELF (F).
Tighten four TWIST-LOCK® FASTENERS.
å Fasten the TOP MOLDING (P) to the TOP (C). Tighten two
TWIST-LOCK® FASTENERS.
Step 4
411312www.sauder.com/services Page 9
C
FA
P
Long finished edge
Curved edge

Step 5
å Push the DOOR STOP (BB) into the hole in the TOP (C).
å Fasten the BOTTOM (D2) to the ENDS (A and B). Use four
BLACK 1-7/8" FLAT HEAD SCREWS (OO).
411312 www.sauder.com/servicesPage 10
D2
C
BB
A
B
Unfinished surface
Rounded edge
BLACK 1-7/8" FLAT HEAD SCREW
(4 used in this step)
OO

å Use a hammer to drive a PROPEL NUT (DD) into the holes in the FEET (EE and FF).
Now, turn an ADJUSTABLE GLIDE (CC) into each PROPEL NUT as shown in the
upper diagram.
å Slide the FEET (EE and FF) into the notches in the SKIRTS (J and K).
å Fasten the SKIRTS (J and K) to the BOTTOM (D2). Use four BLACK 9/16" WAFER
HEAD SCREWS (RR) through the FEET and into the BOTTOM as shown in the
lower diagram.
å NOTE: To raise a corner of the unit, turn the ADJUSTABLE GLIDE
counter-clockwise. To lower a corner, turn the ADJUSTABLE GLIDE clockwise.
Step 6
411312www.sauder.com/services Page 11
D2
J
K
K
J
K
K
CC
DD
FF
FF
EE
EE
BLACK 9/16" WAFER HEAD SCREW
(4 used in this step)
RR
RR
(4 used) Insert the ADJUSTABLE
SHELF (I) between the
ENDS (A and B) before
turning over the unit.
I
A
B

Step 7
å Carefully turn your unit over onto its front edges. Unfold
the BACK (E) and lay it over your unit.
å Make equal margins along all four edges of the BACK (E).
Push on opposite corners of your unit if needed to make
it "square".
å Fasten the BACK (E) to your unit using the NAILS (UU).
å NOTE: Be sure to tap NAILS into the holes that line up
over the SHELF (F).
å NOTE: A perforation has been provided for access
through the BACK. Carefully cut out the hole if needed.
å Fasten the BALLASTS (VV and WW) to the BOTTOM (D2).
Use two BLACK 3" PAN HEAD SCREWS (84S).
411312 www.sauder.com/servicesPage 12
E
These holes must line
up over the SHELF (F).
NAIL
(52 used in this step)
UU
VV
VV
WW
WW
BLACK 3" PAN HEAD SCREW
(2 used in this step)
84S
D2
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution

å Fasten three HINGES (Z) to each DOOR (H). Use twelve
BLACK 1/2" FLAT HEAD SCREWS (SS).
Step 8
411312www.sauder.com/services Page 13
Z
Z
H
H
BLACK 1/2" FLAT HEAD SCREW
(12 used in this step)
SS

Step 9
å Carefully stand your unit upright.
å Before fastening the DOOR to your unit, be sure the
mounting screw is against the stops as shown in the
diagram. If it isn't, loosen the mounting screw to slide it
against the stops. Then tighten the mounting screw.
å Fasten a DOOR (H) to the LEFT END (B). Use the screws
in the HINGES. See the next step for adjustments.
å Fasten a LARGE PULL (GG) to the DOOR (H). Use two
BLACK 7/8" MACHINE SCREWS (PP).
å Repeat this step for the other door.
411312 www.sauder.com/servicesPage 14
H
B
GG
Mounting
screw
Stop
Hinge
Pro Tip: Lift with your
legs. And, you know,
your arms.
BLACK 7/8" MACHINE SCREW
(4 used for the PULLS)
PP

Step 10
411312www.sauder.com/services Page 15
å Refer to the enlarged diagram to identify the parts on the HINGES.
å The DOORS may need some adjustments. Follow the text below to make
needed adjustments.
å DOOR ADJUSTMENTS:
To adjust the DOORS from side to side (horizontal), turn the adjusting screw in
or out.
å To adjust the DOORS up and down (vertical), loosen both vertical adjustment
screws. Move the DOORS up or down to the desired location. Tighten the screws
after making adjustments.
å To adjust the DOORS in or out (depth), loosen the mounting screw one turn
and move the DOORS in or out, as needed. Tighten the mounting screw after
making adjustments.
Adjusting screw (horizontal) Mounting screw (depth)
(vertical adjustment)

Step 11
å Turn a CAM SCREW (8F) into the DRAWER FRONT (L).
å Push a HIDDEN CAM (1F) into the DRAWER BRACE (M65).
411312 www.sauder.com/servicesPage 16
L
8F
1F
Arrow
Do not tighten the HIDDEN CAM in this step.
M65

å Pull the DRAWER FRONT BRACKETS (II) apart and slide them
into the grooves in the DRAWER SIDES (D50 and D51). You
may need to gently tap them in with a hammer.
å NOTE: The DRAWER FRONT BRACKETS are marked "RH"
and "LH" for easy identification.
å Fasten the DRAWER FRONT (L) to the DRAWER
FRONT BRACKETS (II). Use four BLACK 9/16" LARGE
HEAD SCREWS (QQ).
å Slide the DRAWER BOTTOM (D983) into the grooves in the
DRAWER SIDES (D50 and D51) and DRAWER FRONT (L).
Step 12
411312www.sauder.com/services Page 17
L
II
II
L
With the palm of your hand,
tap the DRAWER BOTTOM
down into the groove.
Groove
Unfinished surface
II
1st
2nd
BLACK 9/16" LARGE HEAD SCREW
(4 used in this step)
QQ
D51
D983
D51
D50
D50
VIEW THE T-SLOT BOX VIDEO

Step 13
å Fasten the DRAWER BRACE (M65) to the DRAWER FRONT (L). Tighten
one HIDDEN CAM.
å Fasten the DRAWER BACK (D175 ) to the DRAWER SIDES (D50 and D51) and
DRAWER BRACE (M65). Use five BLACK 1-9/16" FLAT HEAD SCREWS (30S).
411312 www.sauder.com/servicesPage 18
1
2
1st
2nd
Surface with
HIDDEN CAM
D175
D51
D50
L
VIEW THE T-SLOT BOX VIDEO
30S
Start each screw a few turns before
completely tightening any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(5 used in this step)
M65
M65

å Fasten the DRAWER RIGHT (40CC) and DRAWER LEFT (40CD)
to the DRAWER SIDES (D50 and D51). Use four GOLD 5/16"
FLAT HEAD SCREWS (3S) through holes #2 and #4.
å Fasten the PULL (HH) to the DRAWER FRONT (L). Use two
BLACK 7/8" MACHINE SCREWS (PP).
Step 14
411312www.sauder.com/services Page 19
L
HH
Roller end
Roller end
BLACK 7/8" MACHINE SCREW
(2 used for the PULL)
PP
1
2
3
4
1
2
3
4
GOLD 5/16" FLAT HEAD SCREW
(4 used in this step)
3S
D51
D50

Step 15
å Place your unit into its final position against a wall.
å Push the RUBBER SLEEVES (MM) over the METAL PINS (LL).
Insert the METAL PINS into the hole locations of your choice
in the ENDS (A and B). Set the ADJUSTABLE SHELF (I) onto
the METAL PINS.
å Set the ROD (V) onto the ROD HANGERS on
the ENDS (A and B).
411312 www.sauder.com/servicesPage 20
LL
MM
A
B
I
V
(4 used)