Saxby Lighting 103253 User manual

www.saxbylighting.com
Instruction manual
103253, 103254, 103255, 103256, 103257, 103258, 103265, 103266
LED Anti-Corrosive Batten
103253 : 19W LED module (SMD), 4000K
103254 : 24W LED module (SMD), 4000K
103255 : 35W LED module (SMD), 4000K
103256 : 30W LED module (SMD), 4000K
Technical data
220-240 V~, 50 Hz
Supply
Voltage:
Bulb
Type:
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
For your safety, always switch off the power supply before cleaning.
Care and Safety
Conformity with all relevant EC Directive requirements.
Conformity with all relevant UKCA Directive requirements.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or local store for recycling advice.
This product is not suitable for dimming.
Live Voltages may be present in this unit even when turned off or when completely disconnected.
This product is Class 1, must be connected to earth.
Non-replaceable light source Replaceable control gear by a
professional
V1 08/08/2022
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
UK Manufacturer: BH17 7BY
For further information, please visit https://www.lighting-info.co.uk/103253
This product is rated at IP65.
IP 65
This product contains a light source of energy efficiency class D.
103257 : 50W LED module (SMD), 4000K
103258 : 57W LED module (SMD), 4000K
103265 : 24W LED module (SMD), 6500K
103266 : 50W LED module (SMD), 6500K
Caution! Risk of electric shock!

Warning
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Layout
Installation
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Check the pack and make sure you have all the parts listed.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot
restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
This product contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
This is a Class 1 product and must be earthed.
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully
note the position of each set of wires.
Note that the switch is turned off before installation.
The mounting surface must be flat and smooth to ensure a good fit.
• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of
the connection block.
Check that...
Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the junction box and the
each light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boxes
(not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
We recommend that you use H05RN-F specification cable (not supplied) which is an outdoor grade, rubber sheathed cable.
The mains supply cable must have a minimum cross section area of 1.0mm2.
Cables must be protected using suitable conduit or plastic trunking.
Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.
This product can be installed on the ceiling or wall.
X
Model
4FT
5FT
6FT
820±10mm
1120±10mm
1050±10mm
26±1mm
26±1mm
26±1mm
Y
1
4
56
7
2
3
X
Y
“click”
“click”
8
see wiring diagram
Wiring
Having correctly identified the wiring from your existing light fitting and connect to the connection block inside the product in
the following way :
This product is Class I product must be earthed. They must be joined together and well insulated with good quality insulation
tape. This is to ensure earth continuity throughout your property.
• Open the diffuser cover by unfastening securing clips.
• Hold the product in place and mark the position of the fixing
holes. This may require the help of an assistant. If wall
mounting, ensure that the product is level.
• Ensure the ceiling or wall is capable of holding the
weight of the product and then fix brackets in place.
• Close diffuser cover by clipping it into place.
• Replace fuse or circuit breaker and switch on. Your light is
now ready for use.
• Take care to avoid damaging any concealed wiring and pipes.
The correct fixings should be used for brick, cavity walls or
plasterboard.
• Feed the supply cable through the end grommet and fix the
light fitting into position. Alternatively, the grommet can be
removed and the supplied cable gland fitted.
• Connect the supply cable to the quick fit terminal block as
detailed wiring diagram.
• Fix two suspension brackets into the position with the
installation plugs and screws.
• Fix the light fitting by suspension brackets in place.
SUPPLY LIGHT FITTING
SWITCHED LIVE BROWN (L)
BLUE (N)
NEUTRAL
EARTH (GREEN/YELLOW) GREEN/YELLOW
PUSH DOWN
INSERT CABLE