Saxby Lighting 43810 Manual

Instruction leaflet
LED Driver Constant Voltage
43810
www.saxbylighting.com Saxby Lighting Ltd. BH23 3PE
Iss.1 09052012
• Thisproductshouldbeconnectedtothefittingsthat
arebeingpoweredinparallelconfiguration.The
diagrambelowshowsexamplefittingsconnectedin
the correct configuration.
• Payparticularattentiontothenumberofunits
being fitted and the total wattage of these units. We
recommend a maximum load of 10W for the LED
Driver.
• RunthecabletothefirstLEDfitting.Usingan
appropriateterminalblock(notsupplied)thenconnect
thefitting(s)intheconfigurationshown.
• Replacefuseorcircuitbreakerandswitchon.Your
LED driver is now ready for use.
Commissioning
240V
~
50Hz
Constant Voltage
LED Driver
+
_
+_+_+_
Fitting Fitting Fitting
• Thissystemcontainsnon-replaceablepartsand
cannotbeserviced.Ifdamageoccursthepartshould
bescrapped.
• Foryoursafety,alwaysswitchoffthesupplybefore
cleaning.
Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilities
exist.CheckwithyourLocalAuthorityorretailerforrecyclingadvice.
Recycling advice
Safety information
• Alwaysswitchoffordisconnectfromthemainswhen
cleaningtheproduct.
• We recommend cleaning with a soft dry cloth. Never
use scourers, abrasives or chemical cleaners.
• Donotallowmoisturetocomeintocontactwith
electricparts.
43810 - LED Driver.indd 1-2 11/05/2012 10:28:27

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactoryoperationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.
Warning
This LED driver is Double Insulated and
does not require connection to an Earth
circuit.
Please read these instructions carefully before
commencinganywork.
Thisunitmustbefittedbyacompetentandqualified
electrician.
Install in accordance with IEE Wiring regulations and
currentBuildingRegulations.
Topreventelectrocutionswitchoffatmainssupply
before installing or maintaining this fitting. Ensure
otherpersonscannotrestoretheelectricalsupply
withoutyourknowledge.
Thislightfittingshouldbeconnectedtoafusedcircuit.
ThisLEDdrivercontainsnon-replaceablepartsand
cannotbeserviced.Ifdamageoccursthepartshould
bescrapped.
Thisproductcannotbedimmed.
ThisproductisratedatIP20.
Wasteelectricalproductsshouldnotbedisposedof
with household waste. Please recycle where facilities
exist.Checkwithyourlocalauthorityorretailerfor
recycling advice.
Specification
InputVoltage : 220V–240V50–60Hza.c
OutputVoltage : 12W12Vd.c.1.0AMaxConstantVoltage
Cable : 0.75to2.5mmsquared
OperatingTemp : -20˚Cto+50˚C
CaseTemp(tc) : 85˚C
PowerFactor : 0.8
Layout
• Planthedesiredlayoutofthisfittingcarefully,
ensuring the cables will reach the distances between
the LED driver and each LED fitting.
• EnsurethatthereisadequateventilationfortheLED
driver.
• Avoidlocatinganycablesinpositionsthatwould
causeahazard.Positioncablesawayfromareas
wheretheymaybeatriskfrombeingcut,trappedor
damaged.
• Cablesthataretobeinwallsmustbeprotected
usingsuitableconduitorplastictrunking.
• Whenlayingthecablesoutbeawarethatvoltage
droponthelowvoltagesidecanbeafactor.Usea
goodqualitylowresistancecableandarrangethe
layout so that the mains cable is the longer length.
We recommend that a maximum total cable length of
5.0m is used on the low voltage side.
Existingfittingsmustbecompletelyremovedbefore
installationofanewproduct.Beforeremovingthe
existing fitting, carefully note the position of each set
of wires.
• PositiontheLEDdrivernexttothemainsoutletthat
the system will connect to. Do not connect at this
stage. Ensure that the LED driver can be accessed
foranyfuturemaintenancerequirements.
• Removethecovertoaccessthewiringterminals.
Payparticularattentionastowhichismains(PRI)
andwhichisthelowvoltageside(SEC).
• Connectthelowvoltagewiringfirst.Connectthered
wiretothepositiveterminal,andtheblackwireto
the negative terminal.
• Ensurethattheconnectionsaretight,andthatno
loose strands have been left out of the connection
block.
• Connectthemainssupplywiring,ensuring that
browncable(Live)goestotheLconnectorandthat
thebluecable(Neutral)goestotheNconnector.
• Ensurethattheconnectionsaretight,andthatno
loose strands have been left out of the connection
block.
• Replacethecoverensuringthatthecableisgripped
properly.
Direct Wiring
This LED driver is double insulated and must not be
earthed.
• TheLEDDrivercanalsobefittedtoarewireable3
pinplugfittedwitha3ampfuse.Shouldthefuse
requirereplacement,itmustbereplacedwithafuse
ratedat3ampandapprovedtoBS1362.
• Ifthemainsplugisunsuitableforthesocketoutlet
or is removed for any other reason, then the cut off
plugshouldbedisposedofsafelytopreventthe
hazardofelectricshock.
• Thereisadangerofelectricshockifthecutoffplug
isinsertedintoany13ampsocketoutlet.
• Thewiresinthemainsleadonthisapplianceare
colouredinaccordancewiththefollowingcode:
 Blue–Neutral
 Brown–Live
• Usea3AmpFuseapprovedtoBS1362.
E
L
N
Fuse
3Amps
CordClamp
BLUE
Neutral
BROWN
Live
Plug Wiring
Check that...
• Youhavecorrectlyidentifiedthewires.
• Theconnectionsaretight.
• No loose strands have been left out of the connection
block.
43810 - LED Driver.indd 3-4 11/05/2012 10:28:44