Saxby Lighting Seina 78637 User manual

www.saxbylighting.com
Instruction manual
78637, 78638, 78639, 78640, 78641, 99563
Seina
Technical data
220-240 V~, 50 Hz
Supply
Voltage:
Bulb
Type:
78637 / 78638--3.5W LED module (SMD), 4000K
78639 / 78640--3.5W LED module (SMD), 4000K
99563-----------3.5W LED module (SMD), Blue
78641-----------3.5W LED module (SMD), 3000K
The power supply is Double Insulated and does not require connection to an Earth circuit.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or local store for recycling advice.
Having correctly identified the wiring from your existing light fitting, connect to the approved IP67 (or higher rated) terminal
block in the following way (recommended terminal block Ref. 90131/90132)
Wiring
You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the
connection block.
Check that...
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole
luminaire shall be replaced.
Conformity with all relevant EC Directive requirements.
Conformity with all relevant UKCA Directive requirements.
78637
78639
99563
78638
78640
78641
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
For your safety, always switch off the power supply before changing lightbulbs, or cleaning.
Care and Safety
Replace Cracked Shade
The LED's are protected by a plastic lens. The lens part must be replaced immediately should
it become cracked or damaged. This fitting must not be used without the plastic lens in place.
This product is rated at IP44.
IP 44
This product is not suitable for dimming.
NEUTRAL
SWITCHED LIVE
BLUE (N)
BROWN (L)
SUPPLY LIGHT FITTING
V4 12/10/2021
EU Manufacturer: 1 Gnarrenburg, 27442
UK Manufacturer: BH17 7BY

Warning
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Check the pack and make sure you have all the parts listed.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot
restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a circuit with a 30mA RCD fitted.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
If replacing an existing fitting, make a careful note of the connections.
This product is manufactured from marine grade stainless steel, making it suitable for application in coastal environments.
This bricklight product is specifically designed and tested for installation into vertical walls only. Under no circumstances
should it be fitted into the ground or into horizontal surfaces.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Installation
This light fitting is double insulated and does
not require connection to an Earth circuit.
Cables must be protected using suitable conduit or plastic trunking.
Product must only be installed into vertical walls.
• Tighten the cable gland to ensure waterproof seal.
• Re-assemble the bricklight, ensuring the front bezel is securely fitted to ensure waterproof seal.
• Switch on. Your light is now ready for use.
Hex key
Fig 1.
Fig 2.
Hexagonal screw
Front stainless steel panel
Cable for wiring
Inner fitting
Outer frame
Spring clip
x 4
65mm
215mm
Recessed cut out
H65mm x W215mm x D102.5mm
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between each light fitting.
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully
note the position of each set of wires.
• Select a mounting location for the product and prepare a cut out size of H65mm x W215mm x D102.5mm. If removing an
existing brick, the mortar should not be removed.
• Pass the incoming supply cable through the cut out and through the outer frame. Which is an outdoor grade, rubber
sheathed cable. Wire as detailed wiring diagram.
• Fit the 4 spring clips into the outer frame by pushing them into the slots. Ensure they are securely fitted and then securely fit
the outer frame into the wall. See Fig 2.
Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction
boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
The mains supply cable must have a minimum cross sectional area of 1.0mm²
After deciding the layout of the light fitting/s, and the position of the junction box, ensure the cables are long enough to the
desired positions.
Note that the switch is turned off before installation.
• N.B.: for 78637/78638 there is an additional interchangeable Warm White LED module that, if desired, can be purchased
separately. The reference number is 78641. Using the supplied hex key, remove the front panel by unscrewing the two
hexagonal screws. Then disassemble the bricklight; LED module can be replaced with 78641.