Saxby Lighting 46393 Manual

Instruction leaflet
Form Recessed
46393, 51902
www.saxbylighting.com
For your safety, always switch off the supply before cleaning.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling advice.
Recycling advice
Safety information
Saxby Lighting Ltd. BH23 3PE
• Werecommendcleaningwithasoftdrycloth.Do
not use solvents or abrasive cleaners as these could
damage the finish.
• Refitthecoverontheterminalblock.
• Pushthejackconnectorintothesocketonthehead.
• Theceilingsurfacemustbeflatandsmoothtoensure
a good fit.
• Pushthespringclipsupwardsandfitintotheceiling
hole. See Fig 1.
• Pushtheunitupuntilfirmlyinposition,ensuringthat
no cables are trapped. See Fig 2.
• Ensurethattheproductissittingproperlyinthehole.
• Replacefuseor circuitbreaker andswitch on.Your
light is now ready for use.
Commissioning 1.
2.
• TheLED'sinthisproductarenonreplaceable.
Fitting/replacing bulbs
Iss.4 04042016

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
Specification
Voltage: 240V 50Hz
Lamp: 46393:20WCOBLED51902:30WLED(COB)
IP rating: 20
Layout
• Planthedesiredlayoutofthesefittingscarefully,
ensuring the cables will reach the distances between
theLEDDriverandeachlightfitting.
• EnsurethatthereisadequateventilationfortheLED
Driver.
• Avoidlocatinganycablesinpositionsthatwould
causeahazard.Positioncablesandjunctionboxes
(notsupplied)awayfromareaswheretheymaybe
at risk from being cut, trapped or damaged.
• Themainssupplycablemusthaveaminimumcross
sectional area of 1.0mm².
• Thedistancebetweenunitsmustbe0.5mminimum.
• Theunitmustbelocated0.2mawayfromajoist.
• Thisproductmustbemountedoutofarmsreach.
• Thisproductisnotsuitableforbathrooms.
Existing fittings must be completely removed before
installation of a new product. Before removing the
existing fitting, carefully note the position of each set
of wires.
• PositiontheLEDDrivernexttothemainssupplythat
thesystemwillconnectto.Donotconnectatthis
stage.
• Cuta165mmdiameterholefor43693usingan
appropriatetool.Thecutoutsizefor51902is
205mm.
• Ensurethatthevoiddepthisaminimumof200mm.
• Itisrecommendedtocuttheholeslightlysmaller
than needed, then file the hole until the recessed unit
fits snugly.
• Ensurefreemovementofairbyremovingvoid
insulation from at least 150mm from around the
hole. Under no circumstances must these fittings
and drivers be covered with insulating matting or
similar material.
Installation
Wiring
Check that...
• Youhavecorrectlyidentifiedthewires.
• Theconnectionsaretight.
• No loose strands have been left out of the connection
block.
Having correctly identified the wiring from your existing
light fitting, pull the wire through the hole and connect to
the block in the following way:
Thisunitisdoubleinsulatedandmustnotbeearthed.If
thereareanyincomingearthcables,theymustbejoined
togetherandwellinsulatedwithgoodqualityinsulation
tape.Thisistoensureearthcontinuitythroughoutyour
property.
This product is Double Insulated and does
not require connection to an Earth circuit.
Please read these instructions carefully before
commencing any work.
Thisunitmustbefittedbyacompetentandqualified
electrician.
Install in accordance with IEE Wiring regulations and
currentBuildingRegulations.
ThissystemoperatesatSafetyExtraLowVoltage,via
thesuppliedLEDdriver.Neverconnectthelightfittings
directlytothemainswithoutusingthesuppliedLED
driver.
AlwaysdisconnecttheLEDdriverfromthemains
when installing or maintaining this system.
Topreventelectrocutionswitchoffatmainssupply
before installing or maintaining this fitting. Ensure
other persons cannot restore the electrical supply
without your knowledge.
Thislightfittingshouldbeconnectedtoafusedcircuit.
If replacing an existing fitting, make a careful note of
the connections.
Thisfittingmustalwaysbefittedtoaplasterboard
ceiling.Thismustnotbefittedtoaplasterandlath
ceiling
Thissystemcontainsnon-replaceablepartsand
cannot be serviced. If damage occurs the part should
be scrapped.
Thisproductisnotsuitablefordimming.
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.