SDC Z7600 Series User manual

P:\INSTALLATION INST\Electrified Lockset\INST-Z7600 REV B 04-18 Page 1
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email eng[email protected]
A. Door Preparation:
1. Measure desired height from finished floor, mark a horizontal line on door and door edge.
2. Align template on edge of door with applicable horizontal at height line. Check the chart for drilling trim
holes on template and mark only holes for lock function being installed.
3. Mortise door edge according to measurements on
installation template and drill proper holes for trim.
4. Recess for face plate, the dimension is:
L 8-1/32" x W 1-5/16" x D 7/32".
Height line
of lever
or knob
C
L
7/32"
INSTALLATION INSTRUCTIONS
Z7600 SERIES MOTORIZED RETRACTION
MORTISE LOCK SET
of cylinder
of lockcase
of lever
or knob
Vertical centerline
C
Installation
template
C
L
C
L
C
L
Lof
door edge
801 Avenida Acaso, Camarillo, Ca. 93012 • [phone] •
www.sdcsecurity.com • E-mail: [e-mail]
NOTCH OPENING FOR MOTOR
ON WOOD DOORS ONLY
*
B. Strike Installation: 1. Align strike template on jamb.
Be sure to keep 3/8" distance
between lock centerline and
strike centerline. Recess
5/32" for flush fit of strike and
dust box.
2. Mortise jamb according to
measurement of strike template.
Then fit strike and dust box into
frame and secure into place with
supplied screws.
4-7/8"
3-17/32"
3/8"
3/8"
1" Holes
1-1/8" Deep
C
L
Jamb
Lock C
L
C
L
Strike
3/8"
2X 12-24 WMS
5-5/8"
1-1/4”
(1-3/4” DEEP)
3/8”
2-1/4”
1-1/2”
(1-3/4” DEEP)
1" hole
4-3/4“ DEEP
*
WOOD
DOOR

P:\INSTALLATION INST\Electrified Lockset\INST-Z7600 REV B 04-18 Page 2
2. Change hand of lock:
For RH and RHRB, the catch screw will be on the lock case side. For
LH and LHRB, the catch screw will be on the lock cover side.
3. Connect wires as shown on the lock cover diagram.
4. insert lockcase into mortise cut-out and fasten screws to door.
Pull out and turn
1. Change latchbolt handing
If the hand of the latchbolt
doesn’t match the door hand, remove
the fixing screw and pull the latchbolt
out from lock case. Turn the
latchbolt 180 ° to change the
handling. Position latchbolt back,
into case and fasten it.
Instructions for changing lock hand:
C. Install Lockcase
Remove screw
1. Insert spindles as shown
D. Install Spindles
E. Install Lever trim
1. Place the reversible spring cage onto the ferrules with arrow pointing in
direction of lever rotation.
2. Install outside trim with mounting posts through door and position lever
onto the spindle.
3. Install inside spring cage onto the spindle with the arrow pointing in the
direction of inside lever rotation.
4. Install inside mounting plate onto spindle. Tighten with provided screw.
5. Cap inside rose over mounting plate.
Reversible spring cage
Ferrule
Mounting post
Into Mounting post

P:\INSTALLATION INST\Electrified Lockset\INST-Z7600 REV B 04-18 Page 3
1. Screw cylinder into threaded hole of lock case.
2. Tighten the setting screw against cylinder(s) by turning clockwise as shown.
3. Install face plate onto lock case front and fasten with supplied screws.
F. Install Cylinder and Armor Face Plate
USE THIS CAM.
E. Install Lever trim (continued)
6. Screw inside lever into position and tighten lever collar with supplied spanner wrench.
spanner wrench.
Spanner wrench
G. Lock Wiring;
Motor Power
.620A/.160A @ 24vdc
RED +
BLK -
Apply power for a
minimum of 2 secs.
to retract latch.
Remove power to
release latch
LATCH MONITOR
WHT/BLK = COM
ORG/BLK = N/C
YEL/BLK = N/O
3A @ 30vdc
REX
WHT/RED = COM
ORG/RED = N/C
YEL/RED = N/O
3A @ 30vdc
DPS (MC-4)
GRN = COM
RED = N/C
WHT = N/O
(Door Closed)
50ma @ 30vdc

P:\INSTALLATION INST\Electrified Lockset\INST-Z7600 REV B 04-18 Page 4
OPTIONAL
DOOR CORE DRILLING GUIDE
#7000-DG
Make sure the lock hand matches the door hand, use the following diagram to determine the hand of door.
LH
Left Hand
LHRB
Left Hand
Reverse Bevel
INSIDE OF DOOR
OUTSIDE OF DOOR
RH
Right Hand
RHRB
Right Hand
Reverse Bevel
INSIDE OF DOOR
OUTSIDE OF DOOR