Sealey PTB66004SS User manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using these units.
9Locate the units in a suitable work area.
9Keep the work area clean, uncluttered and ensure there is adequate lighting.
WARNING! Use the units on level and solid ground, preferably concrete.
9Keep the units clean and tidy in accordance with good workshop practice.
9Keep children and unauthorised persons away from the work area.
8DO NOT use these units for any purpose other than that for which they are designed.
8DO NOT use the units outdoors.
8DO NOT place the units in a damp or wet location or an area where there is condensation.
8DO NOT clean the units with any solvents which may damage the surfaces or the protective coating.
8888 DO NOT move the units with the drawers out. To avoid tipping, open one drawer at a time and close and secure all drawers whilst
moving.
8888 DO NOT step on the drawers.
2. INTRODUCTION
Heavy-duty welded steel construction for strength and durability. Anti ngerprint stainless steel nish, both solvent and rust resistant. Ball bearing drawer
slides provide superior performance and carry heavier loads, double sets on large drawers. All drawers have full width sand blasted aluminium ‘Lift & Latch’
drawer pulls, making easy access while preventing inadvertent opening when box is being moved. Heavy-duty exterior side handles. Supplied with non-
slip drawer liners tted to each drawer. Gas struts tted to lid makes opening easy. Integral locking system locks all drawers with the turn of a key. Supplied
with 2 keys. Use with Model No. PTB67506SS Rollcab or can be a stand alone unit.
3. SPECIFICATION
Model No: PTB66004SS Model No: PTB67506SS
Overall Size WxDxH (mm): 675 x 460 x 565 Overall Size WxDxH (mm): 675 x 460 x 1030
Medium Drawer (x3): 560 x 385 x 60 Medium Drawer (x3): 560 x 385 x 60
Large Drawer (x1): 560 x 385 x 135 Large Drawer (x2): 560 x 385 x 135
X-Large Drawer (x1): 560 x 385 x 210
4. ASSEMBLY
4.1. These units are heavy, obtain the help of at least one other person before attempting to unpack them.
4.2. INSTALL HANDLE (refer to g.1).
4.2.1. Position the holes on the rollcab and attach with the bolts provided. Tighten securely.
4.3. INSTALL WHEELS (ROLLCABS) (refer to g.2).
4.3.1. Carefully lay rollcab on its back, with a soft mat underneath for protection. Install the two braked casters on the same end as the
handle.
4.3.2. Insert the carriage bolts through washers, then through the casters and into the bottom of the cabinet. Tighten securely.
4.3.3. Install the xed wheels on the opposite end to the handle.
INSTRUCTIONS FOR:
TOPCHEST 4 DRAWER 675MM HEAVY-DUTY/
ROLLCAB 6 DRAWER 675MM HEAVY-DUTY
MODEL No's: PTB66004SS, PTB67506SS
Refer to
instruction
manual
Wear
protective
gloves
fig.1 fig.2
PTB66004SS, PTB67506SS Issue: 3 (H,2,3,F) 05/06/19
Original Language Version
© Jack Sealey Limited
Indoor use
only

4.4. REMOVE DRAWERS (refer to g.3).
4.4.1. Pull drawer out until it is almost fully extended. Push up one black release handle, while pulling down the other hand black release
lever.
4.4.2. Whilst holding the levers in these positions pull the drawer out until it is released from the drawer slide.
4.5. REPLACE DRAWERS
4.5.1. Extend the drawer slides from the tool chest/cabinet.
4.5.2. Insert the brackets on each side of the drawer into the slots in the chest/cabinet slides, being careful that they are properly positioned.
4.5.3. Once properly inserted, completely close the drawer to set the slides in their proper positions.
4.6. RAISE AND RELEASE DRAWER HANDLES (refer to g.4)
4.6.1. These units are equipped with raise and release drawer handles.
4.6.2. To open, lift up the drawer handle, whilst pulling it towards you. To close, shut the drawer rmly, until the latch engages.
4.6.3. If the drawer does not stay closed, the hook may be bent or it may rub against the drawer slides. To x lightly bend the hook until the
drawer will engage in the slide.
4.7. CHEST AND ROLLCAB CONNECTION (refer to g.5) Rollcab PTB67506SS can be tted with Topchest PTB66004SS or PTB660TR.
4.7.1. Place the chest on the rollcab.
4.7.2. Attach the connectors, as shown, to both ends. Ensure that the clip fully engages in the back of the topchest.
Original Language Version
© Jack Sealey Limited
fig.3 fig.4
Fig.5
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500 01284 703534 [e-mail] www.sealey.co.uk
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call
our technical team on [e-mail] or 01284 757505.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.
Parts support is available for this product. Please log on to
www.sealey.co.uk, email [e-mail] or telephone [phone]
PTB66004SS, PTB67506SS Issue: 3 (H,2,3,F) 05/06/19