SECO-LARM Enforcer E-921CPQ User manual

ENFORCER Voice Dialer
16 SECO-LARM U.S.A., Inc.
Dialer will not arm/disarm
•
Try re-entering the PIN number to ensure that you have
entered it correctly.
•While pressing and holding the [P OG] button, use a pen or
paper clip to press the [ ESET] button on the back of the
dialer. This sets the PIN number to the default (000).Then try
to arm/disarm again.
Dialer will not dial out
•
Make sure that the telephone line is working.
•Make sure that you have programmed at least one
telephone number into the unit and that the full number has
been stored.
•Make sure that the system is in Auto Dial mode.
•Ensure that the line to the wall jack is plugged into the
dialer’s “LINE” jack, and any phone extension connected to
the dialer is plugged into the dialer’s “TEL” jack.
Unit doesn’t respond to a call-
back
•
Check to see if another unit (fax or answering machine)
could be answering the call and remove the other unit.
•Adjust the call-in ring detect setting so the dialer will answer.
Difficulty in activating ‘room
monitor’ by telephone remote
control
•
Try pressing the code key again.
•Move to a quieter location as ambient noise may affect the
dialer’s ability to detect the tone signal.
Troubleshooting:
NOTICE:
The information and specifications printed in this manual are current at the time of publication.
However, the SECO-LA M policy is one of continual development and improvement. For this reason,
SECO-LA M reserves the right to change specifications without notice. SECO-LA M is also not responsible
for misprints or typographical errors.
Copyright © 2014 SECO-LA M U.S.A., Inc. All rights reserved. This material may not be reproduced or
copied, in whole or in part, without the written permission of SECO
-
LA M.
SECO
-
LARM
®
U.S.A., Inc.
16842 Millikan Avenue, Irvine, CA 92606
Website: www.seco
-
larm.com
Phone: (949)
261
-
2999 | (800) 662
-
0800
Email: sales@seco
-
larm.com
IMPORTANT
:
Users and installers of this product are responsible for ensuring this product complies with all
national, state, and local laws and statutes related to monitoring and recording audio and video signals.
SECO-LA M will not be held responsible for the use of this product in violation of any current laws or
statutes.
NOTE:
While the system can provide valuable protection to home and property when properly installed, it
cannot guarantee complete protection against intrusion. SECO-
LA M is not responsible for any losses or
damage which may occur during the use of this product.
®
PIHLK1
MiE
-
921CPQ_141204.docx
WARRANTY:
This SECO
-
LA M product is warranted a
gainst defects in material and workmanship while
used in normal service for one (1) year from the date of sale to the original customer. SECO-
LA M’s
obligation is limited to the repair or replacement of any defective part if the unit is returned, transport
ation
prepaid, to SECO-LA M. This Warranty is void if damage is caused by or attributed to acts of God, physical
or electrical misuse or abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation,
or if for any other reason SECO-LA M determines that such equipment is not operating properly as a re
sult
of causes other than defects in material and workmanship. The sole obligation of SECO-
LA M and the
purchaser’s exclusive remedy shall be limited to the replacement or repair only, at SECO-
LA M’s option. In
no event shall SECO-LA M be liable for any sp
ecial, collateral, incidental, or consequential personal or
property damage of any kind to the purchaser or anyone else.
Voice Dialer
Manual
When triggered by an alarm system, the ENFO CE Voice Dialer can call up to 5 numbers and deliver
a user-recorded 20-second voice message, playing repeatedly for one minute. Each number can
contain up to 32 digits, including #, tones, and pauses. T
he LCD shows the number being dialed at each
stage of the dialing process. The receiver can then listen in or broadcast a message to the room
occupants or can disarm the system. The same functions are available by remote call in as well as
arming the system. The dialer includes a home mode (acting like a door chime when the owner is
present) and a panic button. The 105dB built-in siren alarm can be programmed on or off.
Models Available
Certification
E-921CPQ
E-921KPQ

ENFORCER Voice Dialer
2SECO-LARM U.S.A., Inc.
eatures:
•
Trigger-activated alarm and dialer with user-programmable 20-second alarm message
•16-Digit large display with date/time and function icons
•3 Triggers (1 N.C., 2 NO/NC) for multiple zone security
•Call in at any time to listen in to room, broadcast to room, arm, and disarm dialer
•Listen in, broadcast messages to room, and/or disarm during dialer call out
•Programmable PIN number and entry delay timing
•5 Programmable emergency telephone numbers (up to 32 digits each)
•Programmable auto-dialing cycle repeat times
•Home mode function (acts as a door chime when user is at home)
•Panic button
•Back-lit keypad
•Built-in flash memory to protect against system data loss in case of power failure
•Touch-Tone dialing
•Low-battery indicator for backup battery (battery not included)
•DC power input jack (power adapter not included)
•9V battery backup (battery not included)
•Wall-mountable
•Built-in 105dB alarm (with programmable alarm on/off)
•Built-in auxiliary output for external alarm or siren
•Built-in line seizure
Table of Contents:
Features
................................
.........................
2
Parts List ......................................................... 3
Specifications ................................................. 3
Wiring Diagram ............................................... 3
Overview ......................................................... 4
LCD Screen Layout ........................................ 4
Installing the Voice Dialer ........................... 4~5
Programming the Voice Dialer .................... 6~9
Setting and Changing the PIN Number ...... 6
Setting Emergency Phone Numbers ...... 6~7
Deleting a Stored Phone Number ............... 7
Setting the Siren Function .......................... 7
Setting the Auto Dial Function .................... 8
Setting the Number of Auto Dial Cycles ..... 8
Setting the Number of Call-in ings ........... 8
Setting the Entry Delay Time ...................... 9
Setting the Date and Time .......................... 9
ecord and Play Back Emergency
Message ..................................................... 9
Testing the Auto Dial Function ...................... 10
esetting the Voice Dialer ............................ 10
Line Seizure .................................................. 10
Operating the Voice Dialer ...................... 10~13
Arming and Disarming the System ..... 10~11
Panic Button Use ...................................... 11
emote Control by Telephone ............ 11~12
Home Mode Use ....................................... 13
Low-Battery Indicator ................................ 13
View Function ........................................... 13
Tips ............................................................... 13
Program Planner ........................................... 14
FCC Part 68 .................................................. 14
Summary Programming/Operation Chart ..... 15
Also Available from SECO-LARM® ........ 15
Troubleshooting ............................................ 16
ENFORCER Voice Dialer
SECO-LARM U.S.A., Inc. 15
Summary Progra
mming/Operation Chart:
1. Setting/Changing PIN Number (see pg. 6)
Current PIN
[P OG]
[A M/DISA M]
New PIN
[A M/DISA M]
[P OG] x9
2. Setting Emergency Teleph ne Numbers (see pgs. 6~7)
PIN
[P OG] x2
[A M/DISA M]
[#/DOWN] or [*/UP]
Enter Phone
#
[A M/DISA M]
[P OG
] x8
3. Deleting a St red Teleph ne Number (see pg. 7)
PIN
[P OG] x2
[A M/DISA M]
[#/DOWN] or [*/UP]
[DELETE/PAUSE]
[A M/DISA M]
[P OG] x8
4. Setting the Siren Functi n (see pg. 7)
PIN
[P OG] x4
[A M/DISA M]
[#/DOWN] or [*/UP]
[A M/DISA M]
[P OG] x6
5. Setting the Aut Dial Functi n (see pg. 8)
PIN
[P OG] x5
[A M/DISA M]
[#/DOWN] or [*/UP]
[A M/DISA M]
[P OG] x5
6. Setting the Number f Aut Dial Cycles (see pg. 8)
PIN
[P OG] x6
[A M/DISA M]
[#/DOWN] or [*/UP]
[A M/DISA M]
[P OG] x4
7. Setting the Number f Call-in Rings (see pg. 8)
PIN
[P OG] x7
[A M/DISA M]
[#/DOWN] or [*/UP]
[A M/DISA M]
[P OG] x3
8. Setting the Entry Delay Time (see pg. 9)
PIN
[P OG] x8
[A M/DISA M]
[#/DOWN] or [*/UP]
[A M/DISA M]
[P OG] x2
9. Setting the Date/Time (see pg. 9)
PIN
[P OG] x9
[A M/DISA
M]
[#/DOWN] or [*/UP]
[A M/DISA M]
epeat for each position
[P OG] x2
10. Rec rd Emergency Message (see pg. 9) 11. Playback Message (see pg. 9)
PIN
[ EC/PLAY]
Speak message (up to 20 seconds)
[ EC/PLAY]
[ EC/PLAY]
12. Test Aut Dial Functi n (see pg. 10)
(In
Standby Mode)
Press and Hold [P OG]
[#/DOWN] or [*/UP]
Check to see if number is dialed
13. Arm/Disarm System (see pgs. 10~11) 14. Rem te C ntr l by Teleph ne (see pgs. 11~12)
PIN
[A M/DISA M]
eceive Call
Press Key Code on Telephone Keypad
Dial Voice
Dialer Number
Press Key Code on Telephone Keypad
15. View (see pg. 13) 16. Activate/Deactivate H me M de
Last 5 Sensor Trigger ecords
(In Standby Mode)
[#/DOWN]
(see pg. 13)
Stored Emergency
Phone
Numbers
(In Standby Mode)
[*UP]
(In Standby Mode)
[HOME
]
or a complete listing of SECO
-
LARM products, please visit us online at www.seco
-
larm.com.
LED St
robe Light
SL-1301-BAQ
Door/Window Switches,
Magnetic Contacts, etc.
Auto Dialer
E-921APQ
Shock/Vibration Detector
SS-040Q
Tamper Switch
SS-072Q
Photobeam Sensor
E-931-S35RRQ
Also Available from SECO
-
LARM
®
:

ENFORCER Voice Dialer
14 SECO-LARM U.S.A., Inc.
Program Planner:
CC Part 68
:
Use these charts during s
etup to record phone numbers and sensor locations for future reference.
It is recommended that you use a pencil during setup and redo it in ink afterwards. The user
should keep in a safe, easily accessible location and a copy should be retained by the installer.
Program: Numbers
Date:
NUMBER
PRIORITY
TELEPHONE NUMBER
(include area code and dialer prefix as needed, add PBX
pause and extension if applicable, see p. 6-7)
NAME O PARTY TO BE REACHED
1
2
3
4
5
Installation: Triggers
Date:
TRIGGER
GENERAL DESCRIPTION
SENSOR LOCATIONS
1
2
3
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of the
device of this equipment is a label that con
tains, among other information, a product identifier in the format
US:7M7TE02BE921CPQ and EN:0.11B for this equipment.
This equipment uses the following USOC jacks: J-11/ J45/USB/Power Jacks!
A plug and jack used to connect this equipment to the premis
es wiring and telephone network must comply with the
applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is
provided with this product. It is designed to be connected to a compatible modular jack t
hat is also compliant. See
installation instructions for details.
EN ( INGE EQUIVALENT NUMBE S) STATEMENT
Notice: The inger Equivalence Number ( EN) assigned to each terminal device provides an indication of the maximum
number of terminals allowed to
be connected to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the inger Equivalence Numbers of all the devices
does not exceed 5.
If this equipment US: 7M7
TE02BE921CPQ causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone
company will notify the customer as soon as p
ossible. Also, you will be advised of your right to file a complaint with the FCC
if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the
operation of the equipmen
t. If this happens, the telephone company will provide advance notice in order for you to make
necessary modifications to maintain uninterrupted service.
If trouble is experienced with this equipment US: 7M7TE02BE921CPQ, for repair or warranty information
, please contact
Smart G, Inc. If the equipment is causing harm to the telephone network, the telephone company may request that you
disconnect the equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. Cont
act the state public utility commission, public service
commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this US:
7M7TE02BE921CPQ does not di
sable your alarm equipment. If you have questions about what will disable alarm
equipment, consult your telephone company or a qualified installer.
ENFORCER Voice Dialer
SECO-LARM U.S.A., Inc. 3
Back Connection Area (Cover emoved)
LINE TEL
Telephone Wall Jack
+
-
Buzzer (
–
) O/P
Buzzer (+) O/P
or
Telephone Extension
External Alarm/Siren
CA
-
161T
DC Plug-to-Terminal
Block
Power Adapter
(Not Included)
SM
-
206Q*
E
-
964
-
D390Q*
NO/NC Trigger in 1
NO/NC Trigger in 2
N.C. Trigger in 3
Trigger ground
SM
-
200Q*
Note: For proper operation, the telephone extension
line and wall jack line must not be reversed.
Operating voltage
9~12 VDC
Current draw
Max. (at 12VDC)
Standby
5mA
Dialing
20mA
Alarm On
1
5
0mA
elay On
5
0mA
Speaker On
25
0mA
Total
480mA
Emergency voice message length (user recorded)
Up to 20s
Programmable emergency phone numbers
5
Maximum digits per telephone number
32
Backup battery type/life (not included)
9VD
C/≈20
h
Alarm sound level at 12" (30cm)
≥105dB
Trigger inputs
Triggers 1 and 2
NO/NC Trigger (auto
-
detected)
Trigger 3
N.C. Trigger
Trigger input timer
≥500ms
Auxiliary output current (max)
125mA
Operating temperature
32°~104°F (0°~40°C)
Storage tem
perature
-
4°~140°F (
-
20°~60°C)
Weight
11.15
-
oz (
316
g)
Dimensions
6
11
/
16
"
x4
11
/
16
"
x1
1
/
2
"
(170x119x38 mm)
1x
Voice dialer unit
1x
Telephone cable
1x
emote control instruction card
1x
DC Plug
-
to
-
terminal block
3x
Plastic wall anchors
3x
Wall mount screws
1x
Wall mounting template
1x
User manual
Parts List:
* E-964-D390Q Photobeam Detectors, SM-200Q Magnetic Sensors, and SM-206Q Concealed Magnetic Sensors shown as
examples only: For other sensors and products available from SECO-LA M, please visit our website at www.seco-larm.com.
Specifications:
Wiring Diagram:

ENFORCER Voice Dialer
4SECO-LARM U.S.A., Inc.
Overview:
LCD Screen Layout:
Front
Back (Covers emoved)
LCD Display
Speaker
EC/PLAY LED
LOW BATT LED
POWE LED
Numeric Keypad
Microphone
LINE Jack
TEL Jack
Buzzer
Terminal Block (with Trigger 3 Jumper)
DC Power Jack
Battery eceptacle
eset Button
Note: For explanation of symbols, please see Programming the Voice Dialer on pages 6~9.
Installing the Voice Dialer:
Siren Alarm
Auto
Dial
Call
-
Back ings
Home Mode
Activated
Alarm Triggered
Time/Date
PASSWORD
PASSWORDPASSWORD
PASSWORD MEMORY
MEMORYMEMORY
MEMORY LEARN
LEARNLEARN
LEARN ℡
℡℡
℡ CYCLE
CYCLECYCLE
CYCLE ENTRY
ENTRYENTRY
ENTRY 


2015
20152015
2015-
--
-01
0101
01-
--
-01 12
01 1201 12
01 12-
--
-00
0000
00
ARM
ARMARM
ARM
TRIGGER HOME
TRIGGER HOMETRIGGER HOME
TRIGGER HOME
Armed or
Disarmed
Note:
You can program the telephone numbers and voice messages prior to connecting the power
as long as the 9V battery is installed. The standby battery should provide about 20 hours of
operation.
Note: The Voice Dialer uses EEP OM to retain memory in the event of a power loss.
ENFORCER Voice Dialer
SECO-LARM U.S.A., Inc. 13
Operating the
Voice Dialer
, continued:
H me M de Use
To turn off the alarm function and use the dialer as a door chime, set the dialer to “Home” mode. A
chime will ring any time one of the sensors is triggered.
To activate the “Home” mode:
1. Press the [HOME] button once. One chime will sound and the word ‘HOME’ will appear on the
LCD screen.
2. After 60 seconds, another chime indicates that the voice dialer is now in the “Home” mode.
3. When a sensor is activated, the voice dialer will chime twice.
4. If the panic button is pressed, the voice dialer will sound a 30-second alarm and start the
dialing sequence to the programmed emergency numbers.
To deactivate the “Home” mode, simply press the [HOME] button.
Note:
Arming the system deactivates the “Home” mode. After disarming, reactivate the
“Home” mode if desired.
L w
-
Battery (LOW BATT.)
Indicat r
When the charge level of the 9VDC backup battery (not included) is low, the “LOW BATT.” LED
will flash once every 1.5 seconds. eplace the battery in order to continue providing functionality
during a temporary disruption in power.
Note:
In order
to avoid potential damage due to battery leakage
,
d
o not leave
a low battery in
the unit. Also, be sure to remove the battery if the unit is unused for a period of time.
View Functi n
To view the last 5 sensor trigger events, while in standby mode press the [#/DOWN] button.
To view stored emergency telephone numbers, while in standby mode press the [*/UP] button.
Note:
After 10 seconds of inactivity, the voice dialer will automatically exit the view mode and
return to standby.
Tips:
1. Make sure that the full telephone numbers have been stored as they would normally be dialed
from a local phone.
2. The voice dialer is only suitable for single phone lines. It is not compatible with fax machines.
3. Set the number of Call-in rings to be less than the voicemail or message answer point.

ENFORCER Voice Dialer
12 SECO-LARM U.S.A., Inc.
Note:
Should the user have difficulty activating functions remotely by telephone, there may
be too much ambient noise interference. Try pressing the code key again, or move to a
quieter location as ambient noise above 68dB may affect the auto dialer’s ability to detect
the tone signal.
3.
FUNCTION EXPLANATIONS
LISTEN IN – Pressing [1 #] allows a user to hear sound in the room for 50 seconds. A “beep”
will sound at 30 seconds to remind the user that the listen in time will soon end. Pressing [1 #]
again will reset the 50-second period, and entering any other key code will end monitoring and
perform the function. If there is no other key press, the call will disconnect at the end of the 50
seconds.
B OADCAST
–
Pressing
[
2 #
]
allows
a user to speak to
the person in the room for 50
seconds. A ‘beep’ will sound at 30 seconds to remind the user that the time will soon end.
Pressing [2 #] again will reset the 50-second period and entering any other key code (such as
[1 #], oom Monitor) will end broadcasting and perform the other related function. If there is no
other key press, the call will disconnect at the end of the 50 seconds.
N
ote:
Alternating between “Listen In” and “Broadcast” may be useful for a “conversation”
with the room occupant, but a user cannot speak and listen at the same time.
END CALL
-
Pressing [3 #]
will end the call.
A M SYSTEM – Pressing [5 #] during a user callback will arm the system, confirming with
three short “beeps,” and automatically hang up. If there are 5 rapid “beeps” after three short
“beeps,” it means a door/window is not closed. The dialer will then give 5 seconds to disarm
the system.
DISA M SYSTEM – Pressing [6 #] will disarm the system and automatically hang up.
Note:
If the user enters an incorrect password or key code, the voice dialer will sound 5
“beeps” and automatically hang up.
Operating the
Voice Dialer
, continued:
Remote Control by Telephone – Remote Control by User Call In (Call Back), continued:
C. Press one of the following function codes to control the system remotely:
unction
Press key code
Listen in
1 #
Broadcast
2 #
Arm system
5 #
Disarm system
6 #
The user should hear a “beep” in response. If not, enter the function code again.
ENFORCER Voice Dialer
SECO-LARM U.S.A., Inc. 5
Installing the Voice Dialer, continued:
1. Select a location for the dialer near a standard electrical outlet (if user-supplied 12VDC
adapter is to be used), a telephone wall jack, and the alarm control panel, but out of sight. The
dialer should not be exposed to direct sunlight or rain, and must not be mounted near heat
sources such as radiators, heating ducts, or stoves.
2. For wall-mount, use the wall mounting template to
drill holes and attach 3 screws into the wall at the
desired location. For convenience, 5~6ft (1.5~2m)
above the floor is recommended (Fig. 1).
3. emove the cable cover and battery cover from
the back of the voice dialer (Fig. 2).
4. Install a 9VDC backup battery (not included).
eattach the battery cover.
5. Connect the dialer to up to three detectors or
groups of detectors in series using the connection
terminals as shown in the wiring diagram (see pg.
3). The dialer can also be connected to three
separate alarm control panel outputs of a separate
alarm system. When Trigger 3 is used, the jumper
connection to ground must be removed.
6. Power:
a. If the dialer is to be powered from the alarm
control panel, connect the alarm power outputs
to the DC Plug-to-terminal block (included) and
plug into the dialer’s DC power jack (see pg. 3).
b. If using a 12VDC adapter (not included), plug
the adapter into the dialer’s DC power jack.
7. Connect one end of the included telephone cable to
an existing Touch-Tone line wall socket, and the
other end to the dialer’s “LINE” jack. The wall socket
line must be connected to the dialer’s “LINE” jack for
proper operation. Optionally, connect an extension telephone using the telephone’s cable (not
included) to the “TEL” jack (Fig. 3). eattach the cable cover.
8. If an external alarm is desired, connect according to the wiring diagram (see pg. 3).
9. For wall installation, place the unit over the heads of the screws installed in step 2 (Fig. 1) and
slide down. Check that the unit is firmly attached and tighten or loosen the screws as needed.
10. Once all connections are made, the dialer is ready to be programmed.
Fig. 3
Fig. 1
5~6ft
(1.5~2m)
9VDC Battery
(not included)
Fig. 2
Cable
Cover
Battery
Cover

ENFORCER Voice Dialer
6SECO-LARM U.S.A., Inc.
Programming the Voice Dialer:
The setup mode may only be accessed when the dialer is in standby mode. If no key is pressed
within 15 seconds, the dialer will automatically exit the setup mode.
Setting and Changing the PIN Number
1. Enter the current PIN number (factory preset PIN number is ‘000’), and press the [P OG]
button once. ‘PASSWO D’ will flash on the LCD.
2. Press the [A M/DISA M] button to accept.
3. Enter a new PIN number (3-6 digits) followed by the [A M/DISA M] button to confirm.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [P OG]
button until the programming icons disappear to exit the setup mode.
Example
1
–
To store a number with area code 1
-
214
-
555
-
2858 and an office extension 205
(where the PBX requires a 2-second pause before the extension): After scrolling to the desired
number location, enter ‘12145552858,’ press the [DEL/PAUSE] button for 2 seconds until the
letter ‘F’ appears on the LCD screen, enter ‘205’ and press the [A M/DISA M] button.
Note:
If the PIN number is forgotten, press and hold
the [P OG] button
and use a pen or
paper clip to press the [ ESET] button located near the battery receptacle cover on the back
of the unit and release. The unit will return to the factory preset PIN number (000). All other
user programmed settings except the date and time will be retained.
Setting Emergency Ph ne Numbers
1. Enter the PIN number and press the [P OG] button twice or until “MEMO Y” flashes on the
LCD screen.
2. Press the [A M/DISA M] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select one of the number locations 1-5.
Note: The 5 number locations represent the order in which the numbers will be dialed in the
case of an alarm.
4. Enter the number to store including any area codes or dialing prefixes if needed (up to 32
digits, although only the last 16 digits can be shown on the LCD display) using the keypad
followed by the [A M/DISA M]
button to accept and store the number.
Note:
If needed, add a 4
-
second ‘pause’ before a PBX extension number by pressing and
holding the [DEL/PAUSE] button for 2 seconds until the letter ‘F’ appears on the LCD screen,
and then continuing with the extension number as usual. A ‘#’ or ‘*’ can also be entered by
pressing, and holding for two seconds, the [#/DOWN] or [*/UP] buttons respectively. The ‘#’
sign shows as ‘┘’ and the ‘*’ sign shows as ‘└’ on the LCD screen.
ENFORCER Voice Dialer
SECO-LARM U.S.A., Inc. 11
2. To disarm the system, enter the PIN number and press the [A M/DISA M] button.
The dialer will sound a long “beep” and the word “A M” will disappear from the LCD screen.
Panic Butt n Use
1. When the [PANIC] button is pressed, the siren will sound immediately and auto dialing will
commence without delay. If the siren has been programmed to “SOUND
OFF” the siren will not
sound, but silent dialing will commence.
2.
To cancel the alarm and stop auto dialing, enter the PIN number and press the [A M/DISA M]
button. The dialer is now disarmed.
Note:
When the sir
en has been programmed to “
SOUND
OFF,” the siren will not sound and
the dialing will commence silently after the delay time has passed. When the call is answered,
the receiver will hear the user-recorded 20-second emergency message.
Note: If the voice dialer is not connected to a working telephone line, the dialer will “beep” 4
times and the siren will begin to sound without attempting to continue dialing out (this
overrides the “SOUND OFF” setting).
Rem te C ntr l by Tele
ph ne
The system can be remotely controlled and monitored through any Touch-Tone phone, including
mobile phones. The user may either arm or disarm the system, listen in on any activity in the room,
or broadcast a message to those in the room.
1. REMOTE CONTROL WHEN ALARM IS ACTIVATED
When an alarm has been activated and the voice dialer dials the pre-programmed emergency
numbers, the person who answers the call will hear the pre-recorded message and may press
one of the following function codes at any time to control the system remotely:
unction
Press key code
Listen in
1 #
Broadcast
2 #
End call
3 #
Disarm system
6 #
The user should hear a “beep” in response. If not, enter the function code again.
2. REMOTE CONTROL BY USER CALL IN (CALL BACK)
A. Using a mobile phone or any Touch-Tone phone, dial the phone number that the voice
dialer is connected to. The voice dialer will answer and “beep” once after the number of
rings in the pre-programmed call-in ringer detect cycle (3, 5, 7, or 10 rings, see pg. 8).
B. Enter the PIN Number on the phone’s keypad. The dialer will “beep” twice if the correct
code has been entered. If a wrong code is entered, the dialer will disconnect automatically
and the user must dial in again.
Operating
the
Voice Dialer
, continued:

ENFORCER Voice Dialer
10 SECO-LARM U.S.A., Inc.
Testing the Auto Dial unction:
To test the auto dial function, while in standby mode, press and hold the [P OG] button for at least
two seconds. When you hear a ‘beep’ tone, enter the memory location (1~5) of the number you
wish to test. The voice dialer should then dial the chosen number.
Resetting the Voice Dialer:
To reset the Voice Dialer, press and hold the [P OG] button and use a pen or paper clip to press
the [ ESET] button located near the battery receptacle cover on the back of the unit and release.
The unit will return to the factory preset PIN number (000). All other user programmed settings
except the date and time will be retained.
Operating the
Voice Di
aler
:
Arming and Disarming the System:
1. To arm the system, enter the PIN number and press the [A M/DISA M] button.
The dialer will sound three short “beeps” and the words “A M” will appear on the LCD screen.
After 60 seconds, there will be a single “beep” tone to indicate that exit delay time has passed
and the alarm is now fully armed.
During the 60-second delay time after the system is armed, if the system detects trigger 3
indicating an open door or window, a “beep” tone sounds for 5 seconds, the reminder “CLOSE
PLEASE” appears on the LCD screen, and the word “T IGGE ” flashes. If, after 60 seconds,
that door or window is not closed, the alarm will sound and auto dialing will commence.
After the delay, when the system is fully armed, if a door or window connected to the alarm is
opened, the LCD screen will flash the word “T IGGE ”. After the adjustable entry delay time
has passed, the siren will begin to sound (30 seconds on and 30 seconds off) and auto dialing
will commence according to the programmed sequence and cycle times.
Line Seizure:
If the telephone line that the dialer is connected to is in use, the dialer will seize the line,
disconnecting the current call, to dial out. This ensures that the dialer is able to dial emergency
numbers promptly.
N
ote:
For proper operation, the line to the wall jack must be connected to the “LINE” jack of
the dialer. A telephone extension, if used, may be connected only to the “TEL” jack of the
dialer.
ENFORCER Voice Dialer
SECO-LARM U.S.A., Inc. 7
Deleting a St red Ph ne Number
1. Enter the PIN number and press the [P OG] button twice or until “MEMO Y” flashes on the
LCD screen.
2. Press the [A M/DISA M] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select the number you wish to delete.
4. Press the [DEL/PAUSE] button to delete the number.
5. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [P OG]
button until the programming icons disappear to exit the setup mode.
Learn
This function is unused.
Setting the Siren Functi n
This setting allows the user to choose between an audible alarm when triggered, or a ‘silent alarm’
while dialing the emergency numbers. The factory default is “ON”.
1. Enter the PIN number and press the [P OG] button four times or until the alarm icon
( ) flashes on the LCD screen.
2. Press the [A M/DISA M] button to accept. The dialer will “beep” once.
3. Press the [#/DOWN] or [*/UP] button to select either “SOUND ON” or “SOUND OFF” and press
the [A M/DISA M] button to accept.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [P OG]
button until the programming icons disappear to exit the setup mode.
Programming the
Voice Dialer
, continued:
Example 2 – To store a number with area code 1-949-555-1234, and an office extension #200
(where the PBX requires a 2-second pause before the extension): After scrolling to the desired
number location, enter ‘19495551234,’ press the [DEL/PAUSE] button for 2 seconds until the
letter ‘F’ appears on the LCD screen, press the [#/DOWN] button for 2 seconds until the ‘┘’
appears on the LCD screen, enter ‘200,’ and press the [A M/DISA M] button.
Example 3 – To store a local number 555-2858: After scrolling to the desired number location,
enter ‘5552858’ and press the [A M/DISA M] button.
5. epeat for the other numbers to be stored (up to 5 total).
6. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [P OG]
button until the programming icons disappear to exit the setup mode.
Note:
If the dialer is programmed to call a voice pager service which requires operator assistance, the
service should be notified in advance regarding the meaning of the message. Consult local authorities
concerning the permissibility of automatically dialing their emergency numbers before programming.

ENFORCER Voice Dialer
8SECO-LARM U.S.A., Inc.
Note:
1. When the dialer is in standby mode and the (℡
℡℡
℡) icon is ON, the auto dial is disabled.
2. When the dialer is in standby mode and the (℡
℡℡
℡) icon is OFF, the auto dial is enabled.
Setting the Aut Dial Functi n
The user can choose whether or not the dialer will dial the emergency numbers when triggered.
The factory default is “ON”.
1. Enter the PIN number and press the [P OG] button five times or until the phone icon (℡)
flashes on the LCD screen.
2. Press the [A M/DISA M] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select either “ON” or “OFF” and press the
[A M/DISA M] button to accept. The dialer will “beep” once.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [P OG]
button until the programming icons disappear to exit the setup mode.
Programming the
Voice
Dialer
, continued:
Setting the Number f Aut Dial Cycles
This can be set from 1~5 cycles. The factory default is 3 cycles, meaning that the voice dialer will
dial each programmed number 3 times.
1. Enter the PIN number and press the [P OG] button six times or until “CYCLE” flashes on the
LCD screen.
2. Press the [A M/DISA M] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select your choice of 1-5 cycles and press the
[A M/DISA M] button to accept. The dialer will “beep” once.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [P OG]
button until the programming icons disappear to exit the setup mode.
Setting the Number f Call
-
in Rings
This sets the number of call-in rings after which the voice dialer will answer. The factory default is
5 rings, but can be user programmed for 3, 5, 7, or 10 rings.
1. Enter the PIN number and press the [P OG] button seven times or until the bell icon ( )
flashes on the LCD screen.
2. Press the [A M/DISA M] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select 3, 5, 7, or 10 and press the [A M/DISA M]
button to accept. The dialer will “beep” once.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [P OG]
button until the programming icons disappear to exit the setup mode.
ENFORCER Voice Dialer
SECO-LARM U.S.A., Inc. 9
Programming the
Voice Dialer
, continued:
Setting the Entry Delay Time
This allows the user to set the length of time before the alarm will sound, to allow time to disable
the alarm after normal entry. The factory default is 20 seconds, but can be user programmed for 0,
5, 10, 15, or 20 seconds.
1. Enter the PIN number and press the [P OG] button eight times or until “ENT Y” flashes on
the LCD screen.
2. Press the [A M/DISA M] button to accept.
3. Press the [#/DOWN] or [*/UP] button to select 0, 5, 10, 15, or 20 seconds and press the
[A M/DISA M] button to accept. The dialer will “beep” once.
4. Press the [#/DOWN] or [*/UP] button to select other setup categories or press the [P OG]
button until the programming icons disappear to exit the setup mode.
Setting the Date and Time
1. Enter the PIN number and press the [P OG] button nine times or until the clock icon (

)
flashes on the LCD screen.
2. Press the [A M/DISA M] button to accept.
3. The date and time will appear on the LCD screen as 5 sets of numbers representing the year,
month, date, hour, and minute respectively. The first set of numbers (year) will be flashing,
indicating that this can now be changed.
4. Press the [#/DOWN] or [*/UP] button to select the correct number for the year and press the
[A M/DISA M] button to accept and move to the next position. epeat for each position until
complete.
5. Press the [P OG] button until the programming icons disappear to exit the setup mode.
Note: Time is shown using a 24 hour clock.
Rec rd and Play Back Emergency Message
1. Enter the PIN number and press the [ EC/PLAY] button. Speak your message into the
microphone of the voice dialer. The maximum message length is 20 seconds. When finished,
press [ EC/PLAY] again.
Note: You may wish to include instructions for disarming the unit in your message since you
may not remember how to do so at a later date when you receive a message that the alarm
has been triggered.
A suggested message could be, “{Your name}’s security alarm has been activated. Please
enter a command, 1# to monitor the room, 2# to broadcast a message to the room, 3# to end
this call, or 6# to disarm the system.”
2. To listen to a message, press the [ EC/PLAY] button.