SECO-LARM ENFORCER E-931CS22RFCQ User manual

Wireless Entry Alert System
E-931CS22RFCQ
Installation Manual
The ENFORCER Wireless Entry Alert System is a self-contained easy-to-install alert system for
commercial or home applications. Each set contains a reflective photoelectric beam sensor that
when tripped communicates wirelessly with a speaker installed up to 328ft (100m) away*.
Additional speakers may be installed to alert more than one area on the property.
•For monitoring a driveway or for use as an entrance indicator
•No wiring necessary between sensor and speaker
•Sensor range: Up to 22ft (7m)
•Sensor is weatherproof for outdoor use
•Speaker makes chime or alarm sound if beam is interrupted
•Wireless range: Up to 328ft (100m) between the sensor and speaker
•Each sensor can be paired with an unlimited number of speakers
•Each speaker can be paired with up to 5 sensors
*Range may vary depending on the installation and operating environment.

Wireless Entry Alert System
2 SECO-LARM U.S.A., Inc.
Parts List
1x
Sensor
1x
Mode adjustment pin
5x
Mo
unting screws
1x
Speaker
1x
Sensor mounting bracket
2x
Plastic wall anchors
1x
Round 3" reflector
1x
Speaker mounting bracket
2x
Power adaptors
1x
Small screwdriver
1x
Reflector mounting screw
2x
Nuts
2x
Bolts sensor)
1x
Manual
Specifications
Sensor Speaker
Operating voltage 12VDC
Operating frequency 433.92 MHz
Wireless range Up to 328ft (100m)*
Sensing range Up to 22ft (7m) N/A
Current
draw
Standby 5mA 25mA
Active 20mA 100mA
Power input 2.5mm DC Jack
Light source IR LED N/A
Volume N/A 0~90 dB
Alarm time range N/A 3~30 s (Adjustable)
Speaker output N/A Chime/Off/Alarm (selectable)
IP Rating IP55 N/A
Operating temperature 32°~122° F (0°~50° C)
Dimensions 31/4"x29/16"x11/2" (82x66x38 mm) 31/4"x215/16"x19/16" (83x75x40 mm)
*Range may vary depending on the installation and operating environment.
Overview
Speaker Setup
1. Choose Chime Alarm and Off using the alert tone selection switch on the side of the speaker.
2. Adjust the volume by using the included Phillips screwdriver to turn the volume adjustment screw. Turning
clockwise increases the volume; counter-clockwise decreases the volume.
3. Adjust the timer duration by turning the timer adjustment screw using the included screwdriver. Maximum
clockwise sets the timer for 30 seconds; maximum counter-clockwise sets the timer for 3 seconds.
NOTE: Timer mode only applies if Alarm is chosen as the alert tone.
Counter output
Sensor Speaker
2.5mm DC Jack
31/4"
(82mm)
11/2"
(38mm)
ø31/4"
(ø82mm)
Timer Volume
Reflector
31/4"
(83mm)
215/16"
(75mm)
29/16"
(66mm)
19/16"
(40mm)
ø3/16"
(ø4mm)
Cable length
9
7
/
8
" (250mm)
Timer
Volume
2.5mm
DC Jack
Mode button
Alert tone
selector
Alignment
LED

Wireless Entry Alert System
SECO-LARM U.S.A., Inc. 3
Mounting and Installation
1. Determine the mounting location for each component.
a. The reflector and sensor should be installed facing each other
about 2ft (61cm) off the ground.
b. Avoid locations where sunlight or other direct beam of light could
enter the sensing spot on the sensor face.
c. Install the speaker within 328ft (100m) of the sensor noting that
obstructions or interference that may reduce the range.
2. Attach the sensor to its bracket (see Fig. 1) and mount the bracket to a
wall or other surface.
3. Mount the reflector to a flat surface opposite the sensor so that the
reflector is aligned with the sensor face (see Fig. 2).
4. Connect an included power adapter to the sensor. Align by slowly
changing the angles of the sensor and reflector.
NOTE: The red LED turns off when the alignment is correct.
5. Mount the speaker where it can be easily heard. For direct surface
mount drill a small hole and insert the provided screw without
tightening it fully to hang the speaker on the screw. Otherwise attach
it to its bracket and mount the bracket where desired (see Fig. 3).
6. Connect an included power adapter to the speaker and test.
Pairing Optional Additional Speakers (E-931ACC-CQ)
Use one of the two methods below to pair an optional additional speaker with the sensor.
NOTES
•The speaker included with the Wireless Entry Alert System is pre-paired with the sensor.
•When pairing an additional speaker release the mode switch immediately after 2 seconds and hearing the
long beep. Pressing the switch for more than 5 seconds will delete the memory.
Method 1
1. Use the mode adjustment pin
to press and hold the mode
switch until you hear a long
beep. The speaker is now in
learning mode.
2. Trigger the sensor by breaking
its beam. You will hear one
beep.
3. After 10 seconds one long
beep indicates successful
pairing.
Method 2
1. Remove the sensor's side panel
with the included screwdriver.
2. Follow step 1 of Method 1.
3. Press the sensor’s learning button
once. You will hear one beep.
4. After 10 seconds one long beep
indicates successful pairing.
Clearing the Memory
1. Use the included mode
adjustment pin to press and
hold the mode switch until you
hear a long beep and two short
beeps after five seconds.
2. Release the mode button and
the memory has been cleared.
Connecting an Optional Counter (E-931ACC-CQ)
To install a counter (sold separately) follow these instructions.
1. Plug the counter into the counter output jack of the speaker (see Fig. 4).
2. Test the counter. Each time the beam is broken the counter should
automatically increase by 1.
3. Manually add or subtract 1 by pressing the "+" or "-" buttons
4. Reset the counter by pressing RESET.
Learning button
Fig. 1 - Sensor
Sensor
face
Fig. 3 - Speaker
Bracket
mounting
holes
Wall
-
mount
screw
Fig. 2 - Reflector
Fig. 4

Wireless Entry Alert System
FCC COMPLIANCE STATEMENT
FCC ID:
K4E931CS22RF
Information to the user: This equipment has been tested and found to
comply with the limits for a class B digital device pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commerc
ial environment. This equipment
generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction man
ual may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his or her own expense.
CAUTION
:
This sensor was not designed to prevent bodily injury or loss of life.
Use of this sensor in certain security applications may be regulated by local laws or
codes Users and installers of this product are responsible for ensuring that the installation and configuration of this product complies with all national state and lo
cal
laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
California Proposition 65 Warning:
These products may contain chemicals which are known to the State of California to cause c
ancer and birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov.
WARRANTY:
This SECO
-
LARM product is warranted against defects in material and workmanship while used in normal service for
one
(
1
)
year from the date of sale
to the original customer. SECO-LARM’s obligation is limited to the repair or replacement of any defective p
art if the unit is returned transportation prepaid to
SECO-LARM. This Warranty is void if damage is caused by or attributed
to acts of God physical or electrical misuse or abuse neglect repair or alteration improper
or abnormal usage or faulty installation or if for any other reason SECO-
LARM determines that such equipment is not operating properly as a result of causes other
than defects in material and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy shall be lim
ited to the replacement or repair
only at SECO-LARM’s option. In no event shall SECO-
LARM be liable for any special collateral incidental or consequential personal or property damage of any
kind to the purchaser or anyone else.
NOTICE:
The SECO
-
LARM p
olicy is one of continual development and improvement. For that reason SECO LARM reserves the right to change specifications
without
notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A. Inc. or their respective owners. Copyright © 2022
SECO
-
LARM
U.S.A. Inc. All rights reserved.
Sample Applications
Troubleshooting
Sensor red LED does not
turn ON
•Check power adapter and cable
•Remove any shiny metallic objects near installation site
Sensor red LED does not
turn OFF
•Realign the sensor and reflector
•Clean the sensor cover and remove any obstacles
Speaker does not sound
•Make sure speaker is switched to Chime or Alarm
•If using Alarm make sure alarm duration is long enough
•Try pairing the sensor to the speaker. See Pairing the Sensor and
Optional Additional Speaker on page 3
Accessories
Wireless
Speaker
Digital
Counter
Square
Reflector
Reflector
Hood
Door Frame
Bracket
E
-
931ACC
-
SFQ
E
-
931ACC
-
CQ
E
-
931ACC
-
R2Q
E
-
931ACC
-
HR1Q
E
-
931ACC
-
BLS8Q
Storefront Main Entrance Driveway
SECO-LARM ®U.S.A., Inc.
16842 Millikan Avenue Irvine CA 92606
Website:
www.seco
-
larm.com
Phone: [phone] | [phone] Email: [e-mail]
PITSW3
MI_E-931CS22RFCQ_220822.docx