SECO-LARM ENFORCER SH-816S-SMQ Series User manual

SH-816S-SMQ/R shown
4-in-1 Multi-Purpose
Siren/Strobe
Installation Manual
Model Product Mount
SH-816S-BMQ Siren/Message/PA Surface or back box (single-gang double-gang C-type)
SH-816S-SMQ/x* Siren/Strobe/Message/PA Surface or back box (single-gang double-gang C-type)
*Replace "x" with the first letter of the lens color amber blue clear or red.
The ENFORCER 4-in-1 Multi-Purpose Siren/Strobe is multiple communication and signaling
devices in one: siren internal message broadcast and (SH-816S-SMQ only) an LED strobe. It
can
connect to an external source to serve as a public address system in daily use. Depending on
circumstances or application it can also sound a warning siren playback your pre-recorded
message or custom sound from internal memory and/or be used as a PA broadcast system. The
SH-816S-SMQ strobe is available with either amber blue clear or red lenses.
•Multiple devices in one – siren/strobe internal custom emergency message and PA system
•Multiple notification types – strobe siren or audio (pre-recorded or broadcast)
•Multiple audio sources – siren on-board MP3/WAV external public address (PA) system
•Upload your own warning message (MP3 or WAV format up to 2MB) via micro-USB port
•9~15 VDC and low current draw
•2 Alarm inputs – input 1 triggers 115dB siren input 2 overrides input 1 to play custom message
•20W Speaker for PA broadcast input (input not to exceed 2V broadcast interrupts both alarms)
•Built-in tamper alarm output
•Weatherproof for outdoor/indoor use IP65

ENFORCER 4-in-1 Multi-Purpose Siren/Strobe
2 SECO-LARM U.S.A., Inc.
Parts List
1x
Device
4x
Mounting screws
4x
Plastic wall anchors
4x
Screw gas ets
1x
Bac removal tool
1x
Manual
Specifications
Model SH-816S-BMQ SH-816S-SMQ/x*
Type Siren/message/broadcast Siren/message/broadcast + strobe
Operating voltage 9~15 VDC
Alarm inputs 2x Ground trigger – input 2 (custom message/sound) overrides input 1 (siren)
Audio in Audio input voltage cannot exceed 2V
Current
draw
Siren 1A@12VDC
Strobe N/A 50mA@12VDC
Both N/A 1050mA@12VDC
Siren volume 115dB
Spea er rating 20W Peak
Custom message WAV or MP3 format up to 2MB
Upload interface Micro-USB
Strobe flash rate N/A 60 per minute
Tamper output 100mA@30 VAC/VDC
IP Rating IP65
Operating humidity 0~98%
Operating temperature -4°~131° F (-20°~55° C)
Housing Polycarbonate plastic
Dimensions 61/8"x415/16"x41/2" (155x126x115 mm) 61/8"x7"x41/2" (155x178x115 mm)
Weight 1-lb 13-oz (812g) 2-lb 2-oz (957g)
*Replace "x" with the first letter of the desired LED lens color – amber blue clear or red.
Overview Notification Priority
Siren
with
Strobe
415/16"
(126mm)
Siren
7"
(178mm)
61/8" (155mm)
4
1
/
2
"
(115mm
)

ENFORCER 4-in-1 Multi-Purpose Siren/Strobe
SECO-LARM U.S.A., Inc. 3
Installation
1. Determine the desired location and
installation—surface or to a back box.
2. Remove the two screws from the two tabs
that attach the mounting base to the main
unit (See Fig. 1).
3. Squeeze the included base removal tool and
insert through the wiring access hole in the
back of the unit. Release and pull carefully
until the base is removed from the unit.
4. Remove the base removal tool and turn the
mounting base over to view the wiring
terminals (see Fig. 2)
5. Thread the wires (up to 8 depending on
installation see Sample Application pg. 4)
through the center hole in the base.
6. Using the provided mounting screws thread
the screws through the provided gaskets
and then through the four mounting holes in
the base to the wall/back box. Ensure the
engraved arrow on the base is pointing
upward (see Fig. 2).
NOTE: For non-standard boxes drill other
holes engraved in oval indentations
on the mounting base as needed.
7. Connect the wires to the terminals on the
mounting base as shown in Fig. 3 and
referring to the Sample Application on pg. 4.
Note that audio input requires power to the
PWR (+) terminal.
8. Upload a custom message if desired (see
Recording and Uploading a Custom
Message pg. 4).
9. Carefully slide the main unit onto the base
ensuring the correct orientation (note the
notch and arrows) and that the terminal
plugs are correctly engaged (see Fig. 1).
10.Test and remove to adjust broadcast
volume as needed.
11.Secure the main unit to the base using the
two screws removed in step 2.
Fig. 1 Remove base from device
Tamper switch
Orientation
alignment
notch
Tamper
switch hole
Mounting base
removal tool
Terminal block
s
are
on reverse
Micro
-
USB
PA Broadcast
v
olume adjustment
Fig. 2 Mounting base – inner side
Mounting holes
Mounting holes
Tamper
switch
hole
SIREN
(
–
)
MP3/WAV (–)
GND
PWR (+)
P
.
A
. IN
(+)
P.A. IN (–)
TAMPER
TAMPER
Wiring
access
hole
Orientation
alignment
notch
Fig. 3 Mounting base – terminal block detail
Terminal blocks
SIREN
(
–
)
MP3/WAV (–)
GND
PWR (+)
P
.
A
. IN
(+)
P.A. IN (–)
TAMPER
TAMPER

ENFORCER 4-in-1 Multi-Purpose Siren/Strobe
IMPORTANT: Users and installers of this product are responsible for ensuring that the installation and configuration
of this product complies with all national state
and local laws and codes. SECO-LARM will not be held responsible for the use of this product in violation of any current laws or codes.
California Proposition 65 Warning:
These products may contain chemicals which are known to the State of California to cause cancer and birth defects or other
reproductive harm. For more information go to www.P65Warnings.ca.gov.
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for one (1)
year from the date of sale
to the original customer. SECO-LARM’s o
bligation is limited to the repair or replacement of any defective part if the unit is returned transportation prepaid to
SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God physical or electrical misuse or abuse neglec
t repair or alteration improper
or abnormal usage or faulty installation or if for any other reason SECO-
LARM determines that such equipment is not operating properly as a result of causes other
than defects in material and workmanship. The sole obligation of SECO-
LARM and the purchaser’s exclusive remedy shall be limited to the replacement or repair
only at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special collateral incidental or consequential personal or property damage o
f any kind
to the purchaser or anyone else.
NOTICE: The SECO-LARM policy is one of continual development and improvement. For that reason SECO-LARM
reserves the right to change specifications without
notice. SECO-LARM is also not responsible for misprints. All trademarks are the property of SECO-LARM U.S.A. Inc. or their respective owners. Copyright © 2022
SECO LARM U.S.A. Inc. All rights reserved.
Recording and Uploading a Custom Message
1. Record a message using any audio recording app that supports the MP3 or WAV format.
NOTES:
•The device file system supports FAT12 FAT16 and FAT32. File size cannot exceed 2MB.
•Supports MP3 format (sampling 8~48kHz 8~128kbs) or WAV format (sampling
8/11.025/12/16/22.05/24/32/44/1/48kHz).
•The message will loop continuously as long as the MP3/WAV (–) input is triggered.
2. Connect a computer to the device's USB input port (see Fig. 1 pg. 3) using a micro-USB cable.
The device should show up as an external drive on your computer.
3. Copy the file to the device and after the file is completely copied disconnect the device from
your computer (consult your computer's help to learn how to disconnect an external device).
Sample Application
NOTES
•The Strobe (SH-816S-SMQ only) lights during any notification (siren MP3/WAV message or
PA broadcast).
•The MP3/WAV message will override and interrupt the siren for the duration of the message.
•The PA broadcast is not designed for continuous use since it will override and interrupt both the
MP3/WAV message/sound and the siren for the duration of the broadcast.
SIREN (–)
MP3/WAV (–)
GND
PWR (+)
(+)
P.A. IN (+)
P.A. IN (–)
TAMPER
TAMPER
12VDC
Power Supply (
–
)
Alarm
System
PA Broadcast
System
Alarm Output 1
(
–
)
Alarm Output 2 (–)
(Trigger ground
outputs)
(
–
)
(
+
)
SECO-LARM® U.S.A., Inc.
16842 Millikan Avenue Irvine CA
92606
Website:
www.seco
-
larm.com
Phone: [phone] | [phone] Email: [e-mail]
PICAN4
MI_SH-816S-xMQ_220427.docx