Server Extreme 07518 User manual

Server Extreme™
Pump
for purchasing our Server Extreme™ Pump.
Extreme™ pouched condiment systems are sealed and
sanitary, achieve excellent evacuation and have only a
few parts for easy clean-up.
SIMPLIFY CONDIMENT MANAGEMENT— GO POUCHED
Thank You
MODEL:
07518
Used with pouches up to
3 gallons with 38mm tments.

Page 2
ASSEMBLY WASH ALL PARTS
PROPERLY BEFORE USE. See page 3.
into pump housing discharge tube.
Place loop of tting around peg
on end of discharge tube to secure.
INSERT DISCHARGE FITTING
5
INSERT PINCH VALVE
1
into pump housing.
TIP: Squeeze the pinch valve
open before installation to
ensure it isn’t stuck shut.
Wrap loop
around lower
opening to
secure dome.
INSTALL DOME
2
Press dome into
housing fully.
Ensure valve ap
covers bottom
opening.
Lubricate with a small amount of clean water.
Rotate and position until both pegs on
housing t into holes on tube.
INSTALL TUBE
3
Lubricate connector with a small amount of clean water.
Rotate and position until both pegs on connector
t into holes on tube.
INSERT CONNECTOR
4

Page 3
CLEANING
RINSE fully with clear water.
3
SANITIZE
all parts according to local sanitization
requirements. All parts in contact with food
must be sanitized.
4
AIR DRY all parts fully.
5
Use dishwashing soap,
hot water
and nylon brush
YES!
• Dishwasher safe
• Do not use abrasive, caustic or ammonia
based cleansers.
• Do not use cleansing agents with high
concentrations of acid, alkaline or chlorine.
• Do not use metal scrapers or cleaning
pads that could scratch surfaces.
DISASSEMBLE & CLEAN
all washable parts with soap and hot water.
Use brush to clean any conned areas.
2
FLUSH & RINSE
all pump surfaces with hot water.
Place lower end of pump into container
of hot water and operate pump until all
remaining product is expelled and only hot
water is discharged.
1
SAFETY DISASSEMBLY
According to food and safety regulations, most foods
must be stored and/or served at certain temperatures
or they could become hazardous. Check with local food
and safety regulators for specic guidelines. Server
Products, Inc. cannot be responsible for the serving of
potentially hazardous product.
IMPORTANT
Clean, rinse, sanitize, and dry parts daily or regularly to
comply with local sanitization requirements.
TIP: Squeeze the pinch valve
open before installation to
ensure it isn’t stuck shut.
TROUBLESHOOTING
• Ensure pinch valve is inserted in housing.
• Ensure connector is snapped fully in place to
tment in pouch.
• Ensure pump is properly installed in unit.
• Clean pump thoroughly.
PRODUCT DOESN’T PUMP?
• Wet parts with clean water to help t.
DIFFICULT TO ATTACH PARTS?
• Clean thoroughly. Food residue could prevent
a tight seal between dome and housing.
• Ensure dome edges are ush with housing.
DOME POPS OFF?

Page 4 Manual #EM_01751_RevC 100522
GENERAL SERVICE,
REPAIR OR RETURNS
Before sending any item to Server Products for service,
repair, or return, contact Server Products customer
service to request a Return Authorization Number.
Merchandise must be sent to Server Products with this
number. Service is extremely prompt. Typically, units
are repaired and ship out within 48 hours of receipt.
Merchandise being returned for credit must be in new
and unused condition and not more than 90 days old
and will be subject to a 20% restocking charge.
PUMP COMPONENT PART NUMBERS
DOME
07383
PINCH
VALVE
07798
PUMP
HOUSING
07388
CONNECTOR,
ANTI-CHOKE
07507
DISCHARGE
FITTING
07796
HOSE, RIGHT ANGLE
PUMP 07518: USE HOSE 07502
CAP
07517
O-RING, 1-3/16"
85248
SERVER PRODUCTS
LIMITED WARRANTY
This Server product is backed by a two-year
limited warranty against defects in materials and
workmanship. See Server-Products.com for details.
NEED HELP?
Please be prepared with your Model, P/N and
Series located on the lid or base of the unit.
Example:
Chat with us!
[email protected]
262.628.5600 | 800.558.8722
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA
MODEL
XXXX
P/N
#####
SERIES
##X ##X