SKYDANCE T14 User manual

86mm
86mm
36.5mm
Dimension
● Touch panel RGB/RGBW DMX master,
can also used as RGB/RGBW remoter.
● Select RGB or RGBW light type, single zone or 4 zone,
whether as a remoter through 3bit DIP switch.
● Output international standard DMX512/1990 signal,
can connect more than one DMX decoder.
● Ultra sensitive high strength glass touch panel with touch
color slide in the middle and backlighting.
● Smooth and accurate color adjustment by touching the
color wheel.
● Independent brightness adjustment of each RGBW channel
to achieve millions of colors.
● Built in 30 change mode optional, adjustable speed and
brightness.
● Adopt 2.4GHz wireless technology, when used as controller,
can accept up to 10 remoter control. when used as remoter,
can remote control multiple RGBW controller.
● Support single zone independent adjustment,
multiple zone synchronous adjustment.
Summary
Technical Parameters
● : AC85~265VInput voltage
● : DMX+RF(2.4G)Output type
● Grey levels: 256/CH
● Remote distance: 30m
● Working temperature: -30℃~55℃
● : L86×W86×H36.5mmProduct size
● Net weight: 169g
Wall Mounted Touch Panel
RGB/RGBW (2 in 1) LED
DMX512 Master & RF 2.4G Remote
DMX signal
Wiring diagram
: For Single zone turn on/off light.On/Off :
, For 4 Zone: Short press turn on/off current zone light
long press 2s turn off all zone light .
Color slide: Touch to change color.
Mode .: Short press run next mode, long press 2s run mode-cycle
: Static color, adjust bright, short press 10 levels, Bright/Speed
long press 1-5s continuous 256 levels adjustment.
Dynamic mode, adjust speed,short press 10 levels,
long press s the fastest speed.2
: , short press gets white (RGB mix), WFor RGB light
long press 1-5s continuous 256 levels adjust saturation.
, short press turn on/off W channel, For RGBW light
long press 1-5s continuous 256 levels adjust . W channel brightness
1，2，3，4 Zone / Scene:
When used as 4 zone: Short press select and turn on zone light, long press 2s turn off zone light.
Continuous short press multiple zone key, can select multiple zone. synchronous
When used as 4 scene: Short press run the scene, long press 2s save.
Bright
/Speed
White
DI+ DI - GND DO+ D O- GND
POWE R
V+ V-
CH1 V+ CH2 V+ CH3 V + CH4
V+
DI+ DI - GND DO+ D O- GND
POWE R
V+ V-
CH1 V+ C H2 V + CH3 V+ CH 4
V+
DMX signal
AC85-265V
Power input
W
W
Ppwer Sup pl y
5-24VDC
LN
AC110-23 0V
RGBW LED strip
L
N
Key function
Mode
4 Zone
/Scene
RGBW LED strip
DMX dec ode r DMX dec ode r
● Match: Turn on light, turn off, immediately press on/off key for 5s,
within 5s, press any key of the remoter.
● Delete: Turn on light, turn off, immediately press on/off key for 10s,
delete all matched remoters.
Panel controller match remoter method
Panel remoter match receiver method
For controller with match key
● Match: Short press match key, within 5s, press on/off or zone key of the panel.
● Delete: Long press match key for 5s, delete all matched remoters.
For smart lamp
● Match: Switch off the power, then switch on power again,
short press on/off or zone key 3 times of the panel within 5s after power on,
the link is done once the light blinks 3 times.
● Delete: Switch off the power, then switch on power again,
short press on/off or zone key 5 times of the panel within 5s after power on,
the unlink is done once the light blinks 5 times.
Color slide
On/Off
T14
Dip switch setting
ON
2
1,2,3,4 SCENE
1,2,3,4 ZONE
ON
1
RGB
RGBW
RF OUT OFF
ON
3
● Dip switch 1st bit: set downside is RGB type,
set upside("ON") is RGBW type.
● Dip switch 2nd bit: set downside is single zo ne(4 scene),
set upside("ON") is 4 zone.
● Dip switch 3rd bit: set downside disable remoter,
set upside("ON") enable rem oter.
Caution: before power on, you must confirm the selection of dip switch.
● RGB light type, each zone 3 channel,
Order is red, green, blue, namely
zone 1 is channel 1 ~ 3,
zone 2 is channel 4 ~ 6 ,
zone 3 is channel 7 ~ 9 ,
zone 4 is channel 10 ~ 12.
● RGBW light type, each zone 4 channel,
Order is red, green, blue, white, namely
zone 1 is channel 1 ~ 4,
zone 2 is channel 5 ~ 8,
zone 3 is channel 9 ~ 12,
zone 4 is channel 13 ~ 16.

1. Flip panel, inserted into the card edge aperture with a small screwdriver, gently
pry and open the panel. pull out FPC lock catch, then remove FPC line.
Installation diagram
bottom case upper case
2. After connect wires, put bottom case into 86 bottom box, put in the screw
and tighten.
3. Connect FPC line. then from top to bottom, moderately cover upper case,
complete installation.
bottom case
upper case
NOTES:
● In order to ensure safety, turn off the power first before wiring, ensure correct wiring
to avoid short circuit.
● In the process of installation, do not damage or twist FPC line, in order to avoid damage.
RGB change mode list
No. Name
1
2
3
4
5
6
7
8
9
10
Static red
Static green
Static blue
Static yellow
Static cyan
Static purple
Static white
RGB jump
7 color jump
Red strobe
No. Name No. Name
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Green strobe
Blue strobe
White strobe
RGB strobe
7 color strobe
Red fade in and out
Green fade in and out
Blue fade in and out
White fade in and out
RGBW fade in and out
Red yellow smooth
Green cyan smooth
Blue purple smooth
Blue white smooth
RGB+W smooth
RGBW smooth
RGBY smooth
Yellow cyan purple smooth
RGB smooth
6 color smooth
Malfunctions analysis & troubleshooting
Malfunctions
Causes Troubleshooting
1. The batter y has no power.
2. Beyond controllable distance.
3. The controller did not match the
remoter.
1. Replace batter y.
2. Reduce remote distance.
3. Re-match the remoter.
1. No power.
2. Wrong connection or insecure.
1. Check the power.
2. Check the connection.
No light
1. DMX decoder first address error.
2. Wrong connection of RGBW wires.
1. Check the DMX first address.
2. Reconnect RGBW wires.
Wrong color
No response
from the remoter
1. The product shall be installed and serviced by a qualified person.
2. This product is non-waterproof. Please avoid the sun and rain.
3. Good heat dissipation will prolong the working life of the controller, please ensure
good ventilation.
4. Please check if the output voltage of any power supplies used comply with the
working voltage of the product.
5. Ensure all wire connections and polarities are correct and secure before applying
power to avoid any damages to the LED lights.
6. If a fault occurs please return the product to your supplier. Do not attempt to fix this
product by yourself.
Safety & Warnings
Warranty Agreement
1. 3-year warranty:
● The warranty is for free repair or replacement and covers manufacturing faults only.
● Do not include fees of on site maintenance and consumable parts.
2. Limited Warranty
● Artificial damage caused by improper use, such as use inappropriate power supply,
improper accessories, improper installation, did not follow the instructions, error using
or negligence.
● Any damages caused by force majeure, such as natural disaster, abnormal voltage.
● The normal use of products caused by aging, wear and tear, but it does not affect the
normal use.