Solplanet ASW05kH-T2 User manual

Android iosiOS
ASW05kH/06kH/08kH/10kH/12kH-T2
ASW05kH/06kH/08kH/10kH/12kH-T2-O
ASW08kH/10kH/12kH-T3
ASW08kH/10kH/12kH-T3-O
Three phase hybrid inverter
Quick Installation Guide

The product is a transformerless hybrid inverter with 2 or 3 MPP trackers and a battery
connection that feeds the direct current of the PV array into the connected battery or
converts it to grid-compliant three-phase current and then feeds it into the utility grid.
The product also can convert the direct current supplied by the battery into grid-com-
pliant three-phase current. The product has a backup function that can continue to
supply selected circuits with power from the battery or PV system in the event of a grid
fault.
The product is intended for indoor and outdoor applications.
The product must only be connected with PV modules of protection class II (in accor-
dance with IEC 61730, application class A). Do not connect any sources of energy other
than PV modules to the product.
The product is not equipped with an integrated transformer and therefore has no
galvanic isolation. The product must not be operated with PV modules which require
functional grounding of either the positive or negative PV conductors. This can cause
the product to be irreparably damaged. The product may be operated with PV modules
with frames that require protective earthing.
All components must remain within their permitted operating ranges and their installa-
tion requirements at all times.
Use the product only in accordance with the information provided in the user manual
and with the locally applicable standards and directives. Any other application may
cause personal injury or damage to property.
This quick installation guide does not replace the description in the user manual.
The contents of this guide may be updated or revised due to product development. The
information in this guide is subject to change without notice. The latest version of this
document and the manual for installation, commissioning, configuration and decom-
missioning are to be found in PDF format at www.solplanet.net.
2.1 I
ntended use
SAFETY
2
GENERAL INFORMATION
1
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323
1

2.2 Important safety instructions
The product has been designed and tested strictly according to the international safety
requirements. As with all electrical or electronical devices, there are residual risks
despite careful construction. To prevent personal injury and property damage and to
ensure long-term operation of the product, read this section carefully and observe all
safety information at all times.
DANGER
！
Danger to life due to high voltages of the PV array or the battery！
The DC cables connected to the battery or the PV array may be live. Touching the DC
conductors or the live components can cause to lethal electric shocks. If you discon-
nect the DC connectors from the product under load, an electric arc may occur lead-
ing to electric shock and burns.
• Do not touch non-insulated cable ends.
• Do not touch the DC conductors.
• Do not touch any live components of the product.
• Do not open the product.
• Observe all safety information of the battery manufacturer.
• All work on the product must only be carried out by qualified personnel who have
read and fully understood all safety information contained in this document and
the user manual.
•Disconnect the product from all voltage and energy sources and ensure it cannot
be reconnected before working on the product.
• Wear suitable personal protective equipment for all work on the product.
The product must only be operated in connection with an intrinsically safe lithium-ion
battery approved by AISWEI. The entire battery voltage range must be completely
within the permissible input voltage range of the product.
The product must only be used in countries for which it is approved by AISWEI and the
grid operator.
The type label must be permanently attached to the product and must be in a legible
condition.
This document does not replace any regional, state, provincial, federal or national laws,
regulations or standards that apply to the installation, electrical safety and use of the
product.
2
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323

DANGER
！
Danger to life due to electric shock when touching live components in
backup mode！
Even if the AC breaker and the PV switch of the inverter are disconnected, the parts
of the system may still be live when the battery is switched on due to backup mode.
• Do not open the product.
•Disconnect the product from all voltage and energy sources and ensure it can
not be reconnected before working on the product.
DANGER
！
Danger to life due to fire or explosion when batteries are fully
discharged！
A fire may occur due to incorrect charging of fully discharged batteries. This can
result in death or serious injury.
•Make sure that the battery is not fully discharged before commissioning the
system.
•Contact the battery manufacturer for further proceedings if the battery is fully
discharged.
DANGER
！
Danger to life due to burns caused by electric arcs through short-cir-
cuit currents！
Short-circuit currents in the battery can cause heat accumulation and electric arcs if
the battery is short circuited or wrongly installed. Heat accumulation and electric
arcs may result in lethal injuries due to burns.
•Disconnect the battery from all voltages sources prior to performing any work
on the battery.
•Only use properly insulated tools to prevent accidental electric shock or short
circuits during installation.
• Observe all safety information of the battery manufacturer
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323
3

DANGER
！
Danger to life due to electric shock when touching live system compo-
nents in case of a ground fault！
If a ground fault occurs, parts of the system may still be live. Touching live parts and
cables may result in death or lethal injuries due to electric shock.
•Disconnect the product from voltage and energy sources and ensure it cannot
be reconnected before working on the device.
• Only touch the cables of the PV modules on their insulation.
• Do not touch any parts of the substructure or frame of the PV array.
• Do not connect PV strings with ground faults to the product.
WARNING
！
Danger to life due to electric shock from destruction of the measuring
device due to overvoltage！
Overvoltage can damage a measuring device and result in voltage being present in
the enclosure of the measuring device. Touching the live enclosure of the measuring
device results in death or lethal injuries due to electric shock.
• Only use measuring devices with the measurement span higher than the DC
input voltage range equal to or higher than the voltage rating of the product.
CAUTION
！
Risk of burns due to high temperature.
Some parts of the enclosure can become hot during operation.
•During operation, do not touch any parts other than the enclosure lid of the
product.
CAUTION
！
Risk of injury due to weight of product .
Injuries may result if the product is lifted incorrectly or dropped while being trans-
ported or mounted.
•Transport and lift the product carefully. Take the weight of the product into
account.
• Wear suitable personal protective equipment for all work on the product.
3
4
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323

2.3 Symbols on the label
Beware of a danger zone！
This symbol indicates that the product must be additionally grounded if additional
grounding or equipotential bonding is required at the installation site.
Beware of high voltage and operating current！
The inverter operates at high voltage and current. Work on the inverter must only be
carried out by skilled and authorized electricians.
Beware of hot surfaces！
The inverter can get hot during operation. Avoid contact during operation.
Observe the documentation
Observe all documentation supplied with the product.
Capacitor discharge
Danger to life due to high voltages in the inverter. Do not touch live parts for 10 minutes
after disconnection from the power sources.
CE marking
The product complies with the requirements of the applicable EU directives.
Certification mark
The product has been tested by TUV and got the quality certification mark.
RCM (Regulatory Compliance Mark)
The product complies with the requirements of the applicable Australian standards.
WEEE designation
Do not dispose of the product together with the household waste but in accordance with
the disposal regulations for electronic waste applicable at the installation site.
10mins
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323
5

SYSTEM WIRING DIAGRAM
3
Australia
PV Grid
Grid
L1 L2 L3 N PE
L1 L2 L3 N
PE
L1 L2 L3 N PE
RCD
RCD
N-Bar
PE-N Link
CT1
CT2
CT3
Main
Meter
Normal
Loads
Backup
Loads
Load
PE-Bar
Battery
×Don’t connect this terminal for Australian
and New Zealand grid system!!!
The additional grounding screw hole at the lower right conner
Inverter
AC Breaker
AC Breaker
CT COM
DC Breaker
AC Breaker
6
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323

Europe
PV Grid
Grid
L1 L2 L3 N PE
L1 L2 L3 N
PE
L1 L2 L3 N PE
RCD
RCD
CT1
CT2
CT3
Main
Meter
Normal
Loads
Backup
Loads
Load
PE-Bar
Battery
×
The additional grounding screw hole at the lower right conner
Inverter
CT COM
AC Breaker
AC Breaker
DC Breaker
AC Breaker
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323
7

EU DECLARATION OF CONFORMITY
4
Within the scope of the EU directives
Radio Equipment Directive 2014/53/EU
(L 153/62-106. May 22. 2014) (RED)
Restriction of the use of certain hazardous substances 2011/65/EU
(L 174/88, June 8, 2011) and 2015/863/EU (L 137/10, March 31,2015) (RoHS)
AISWEI Technology Co., Ltd. confirms herewith that the products described in this
document are in compliance with the fundamental requirements and other relevant
provisions of the above mentioned directives. The entire EU Declaration of Conformi-
ty can be found at www.solplanet.net.
8
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323

OVERVIEW
5
SCOPE OF DELIVERY
6
1
1LED指示灯 指示逆变器当前的工作状态
Object Description
3
2DC-switch
Battery Port
4
5
6
7
PV Input
Ai-Dongle
Communication ports
EPS connector
8Additional grounding screw
AC connector
Inverter×1
External CT ×3
Fastener
package ×1
AC connector ×1
Communication terminal package ×1 Document ×1
DC connector ×3/4
Wall Bracket ×1 Ai-Dongle ×1
EPS connector ×1
COM0
BATTERY
LOAD
GRID
ON
OFF
PV1 PV2
PV3
7
8
1 2 3 5 6
4
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323
9

MOUNTING ENVIRONMENT
7
√× √ √ × ×
IP66
4K4H
-25℃
+60℃
≤100%
max.4000m
×
√× √× ×
＞75°
√
≥500mm
≥500mm
≥500mm
≥500mm
≥500mm ≥500mm
10
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323

DIMENSIONS
8
MOUNTING
9
Unit：mm
545
204.5
465
1
90°
Φ10 mm
70mm
2
3 4
10mm
5N·m
35 100
170
486
430
4-9×17（Lumbar foramen）2-φ9
45
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323
11

SECOND PROTECTIVE GROUNDING
10
L=E+(2~3)mm L
E
1
2
3
4
5
5
7
6
M5
3N
· m
M5
3N
· m
12
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323

AC CONNECTION
11
12
34
56
30 10
33 10
PE
12.5~17.5mm
4mm²~6mm²
L2
L1
PE
N
L3
U
V
W
N
OK
click
click
7 8 9 10
1
11
1
2
2
2
2
3
1.2±0.1N·m
2mm
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323
13

BACKUP LOAD CONNECTION
12
L2
L1
PE N
L3
click OK
12
34
56
30 10
33 10
12.5~17.5mm
4mm²~6mm²
click
1.2±0.1N·m
2mm
7 8 9 10
1
11
1
2
2
2
2
3
PE
U
V
W
N
14
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323

PV CONNECTION
13
OK
2.5-6mm2
Φ-5 8mm
≈12mm
click
√×
TYPE 1 - Phoenix Contact
TYPE 2
4
2.5-6mm2
Φ-5 8mm
8-10mm
OK
1
1
1
2
2
1
2
2
3
1
2
3
123
123
45
45
67
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323
15

BATTERY CONNECTION
14
OK
12
3
16
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323

COMMUNICATION SETUP
15
15.1 Communication connection
M4
USB
RJ45-1 RJ45-3 RJ45-5
RJ45-2 RJ45-6RJ45-4
Terminal-1
Terminal-2
Terminal-3
Terminal-4
Object Description
RJ45-3
RJ45-4
Terminal PIN definition
1 2 34 5 6 7
Monitor COM2 RS485A RS485B GND X X X RS485A RS485B
BMS COM5 X GND X CANAH CANAL X RS485A RS485B
8
12
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323
17

1 2 1 2 34 1 2 3456
1 2 1 2 34 1 2 345 6
Φ4-8mm
12345678
1
2
3
4
5
6
7
8PIN
M4
1.6N·m
Terminal-1
Terminal-2
Terminal-3
Object Description
DO1/DO2
\
DI*4/DRM0
Terminal
6pin
4pin
6pin
RS485A
B
DI_4
PIN Definition
1
RS485B
A
DI_3
2
B
DI_2
3
A
DI_1
4 5 6
Smart Meter
Ripple Control Receiver Device DRMS Device
PT100 Temperture Sensor UFR Device
Multifunction Relay 1 Multifunction Relay 2
Negative
Positive Positive Negative
CT 6pin
Red Black Red Black Red Black
Terminal-4
Current Transformer 1 Current Transformer 2 Current Transformer 3
REF GEN/0 COM LOAD/0
or GND
1
2
3
45
18
QG0049_ASW05-12KH-T2-T3_EN_540-300254-00_0323