Sony BKS-R6010 User manual

MAINTENANCE MANUAL
1st Edition (Revised 1)
Serial No. 10001 and Higher
UNIVERSAL LCD REMOTE PANEL
BKS-R6010

!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l'entretien. Afin de
réduire les risques de décharge électrique, d'incendie ou de blessure n'effectuer que les
réparations indiquées dans le mode d'emploi à moins d'être qualifié pour en effectuer d'autres.
Pour toute réparation faire appel à une personne compétente uniquement.
BKS-R6010 MM

BKS-R6010 MM
Vorsicht!
Explosionsgefahr bei unsachgemäßem Austausch
der Batterie.
Ersatz nur durch denselben oder einen vom
Hersteller empfohlenen ähnlichen Typ. Entsorgung
gebrauchter Batterien nach Angaben des
Herstellers.
ATTENTION
Il y a danger d’explosion s’il y a remplacement
incorrect de la batterie.
Remplacer uniquement avec une batterie du même
type ou d’un type équivalent recommandé par le
constructeur.
Mettre au rebut les batteries usagées conformément
aux instructions du fabricant.
ADVARSEL!
Lithiumbatteri-Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandøren.
ADVARSEL
Lithiumbatteri - Eksplosjonsfare.
Ved utskifting benyttes kun batteri som
anbefalt av apparatfabrikanten.
Brukt batteri returneres
apparatleverandøren.
VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en likvärdig typ
som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt gällande
föreskrifter.
VAROITUS
Paristo voi räjähtää jos se on virheellisesti
asennettu.
Vaihda paristo ainoastaan laitevalmistajan
suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to the
manufacturer’s instructions.
When using a modular jack cable:
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to the
following port(s).
: NETWORK connector
Follow the instructions for the above port(s).
1 (P)

BKS-R6010 MM
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
5. Install the equipment while taking the operating
temperature of the equipment into consideration
For the operating temperature of the equipment, refer
to the specifications of the Installation Manual.
6. When performing the installation, keep the
following space away from walls in order to
obtain proper exhaust and radiation of heat.
Rear: 10 cm (4 inches) or more
WARNING
This unit has no power switch.
When installing the unit, incorporate a readily
accessible disconnect device in the fixed wiring, or
connect the power cord to a socket-outlet which must
be provided near the unit and easily accessible, so that
the user can turn off the power in case a fault should
occur.
WARNUNG
Dieses Gerät hat keinen Netzschalter.
Beim Einbau des Geräts ist daher im Festkabel ein
leicht zugänglicher Unterbrecher einzufügen, oder das
Netzkabel mu
ß mit einer in der Nähe des Geräts
befindlichen, leicht zugänglichen Wandsteckdose
verbunden werden, damit sich bei einer
Funktionsstörung die Stromversorgung zum Gerät
jederzeit unterbrechen lä
ß t.
2 (P)

1 (E)
BKS-R6010 MM
Table of Contents
Manual Structure
Purpose of this manual ........................................................... 3 (E)
Related manuals ..................................................................... 3 (E)
Trademarks ............................................................................. 3 (E)
1. Service Overview
1-1. Main Parts Location ................................................. 1-1 (E)
1-2. Main Parts Replacement .......................................... 1-1 (E)
1-2-1. Removal of Cabinet ........................................ 1-1 (E)
1-2-2. PS-735/756 Board (Power Supply Unit)
Replacement ................................................... 1-2 (E)
1-2-3. Replacing the Lithium Battery (CR2032) ...... 1-2 (E)
1-3. Upgrading the Application Software Version ......... 1-3 (E)
1-4. Writing the PLD Data .............................................. 1-4 (E)
1-5. Cleaning for Remote Control Panel ......................... 1-4 (E)
1-6. Circuit-Protection Part ............................................. 1-4 (E)
1-7. Unleaded Solder ....................................................... 1-4 (E)
1-8. Downloading the Font Data
<BKS-R6010 (Ver.2.00 or higher)> ........................ 1-5 (E)
2. Spare Parts
2-1. Notes on Repair Parts ..................................................... 2-1
2-2. Exploded Views .............................................................. 2-2
2-3. Electrical Parts List ......................................................... 2-4
2-4. Supplied Accessories List ............................................. 2-35
3. Semiconductor Pin Assignments
4. Block Diagrams
Overall ............................................................................ 4-1
CA-72 ............................................................................. 4-2
CPU-417 ......................................................................... 4-3
KY-627 ........................................................................... 4-4
5. Schematic Diagrams
PS-735 ............................................................................. 5-1
PS-756 ............................................................................. 5-1
CA-72 ............................................................................. 5-2
CPU-417 ....................................................................... 5-15
KY-627 ......................................................................... 5-22
SW-1377 ....................................................................... 5-32
Frame Wiring ................................................................ 5-33
6. Board Layouts
CA-72 ............................................................................. 6-1
CPU-417 ......................................................................... 6-2
SW-1377 ......................................................................... 6-2
KY-627 ........................................................................... 6-3
PS-735 ............................................................................. 6-4
PS-756 ............................................................................. 6-4

3 (E)
BKS-R6010 MM
Purpose of this manual
This manual is the maintenance manual of Universal LCD Remote Panel BKS-R6010.
This manual describes the information that premises the parts level service (parts
replacement, parts list, diagrams, etc.).
Related manuals
Besides this Maintenance Manual, the following manuals are prepared for the BKS-
R6010.
..
..
.Operation and Installation Guide (Supplied with the unit)
This manual describes the cautions on the operation of this unit and the setting of
station numbers.
..
..
.Operation Manual (Available on request)
This manual describes the detailed information on how to operate this unit.
The operation manual is stored as a PDF file in the CD-ROM supplied with the
IXS-6600-C/IXS-6700-C.
If this manual is required, please contact your local Sony Sales Office/Service
Center.
..
..
.Installation Manual (Available on request)
This manual deicribes the information on installing the BKS-R6010.
If this manual is required, please contact your local Sony Sales Office/Service Center.
..
..
.System Setup Manual (Available on request)
This manual describes the routing switcher system setting and operation confirmation.
If this manual is required, please contact your local Sony Sales Office/Service Center.
..
..
.Protocol Manual (Available on request)
This manual describes the protocol for controlling this unit.
The manual below is provided for the protocol that this unit can support.
If this manual is required, please contact your local Sony Sales Office/Service Center.
SONY ROUTING SWITCHER SYSTEM
REMOTE1 (S-BUS/ROT16) PROTOCOL and COMMAND SPECIFICATIONS
Part No.: 9-977-477-xx
SONY ROUTING SWITCHER SYSTEM
REMOTE2 (Cart++) PROTOCOL and COMMAND SPECIFICATIONS
Part No.: 9-967-261-2x
Trademarks
Trademarks and registered trademarks used in this manual are follows.
.Ethernet is a registered trademark of Xerox Corporation.
.IBM and AT are registered trademarks of International Business Machines
Corporation.
.Windows is a registered trademark of Microsoft Corporation.
Manual Structure

1-1 (E)
BKS-R6010 MM
1-2. Main Parts Replacement
1-2-1. Removal of Cabinet
Front panel assembly
1. Remove the six screws.
2. Remove the front panel assembly.
(The knob is removed together.)
n
To prevent damage, do not remove the knob alone.
1-1. Main Parts Location
Top plate
Remove the three screws, then remove the top plate in the
direction indicated by the arrow.
PSW3 x6
Top plate
PSW3 x6
PSW3 x6
Section 1
Service Overview
PS-735/756
board
CA-72 board
CPU-417 board
Switching regulator
KY-627 board
SW-1377 board
B3 x6
B3 x6
Knob
Front panel
assembly

1-2 (E) BKS-R6010 MM
1-2-2. PS-735/756 Board (Power Supply Unit)
Replacement
n
The PS-735 board (Power Supply Unit) (Part No. : A-
1256-255-A) or the PS-756 board (Power Supplly Unit)
requires periodic replacement.
PS-735 board: Serial No. 10001 to 10060
PS-756 board: Serial No. 10061 or higher
Replacing of the PS-735/756 board every seven years is
recommended.
Perform replacement in the following procedure.
w
Unplug the power supply cord before replacing the PS-
735/756 board.
n
Do not disassemble the switching regulator.
Removal
1. Remove the top plate. (Refer to Section 1-2-1.)
2. Disconnect the connector (CN101) of harness.
3. Remove the two screws (PSW3x12), and then remove
the plug holder (A) and the plate nut.
4. Remove the three screws (PSW3x6), and then remove
the PS-735/756 board and the insulating sheet.
Installation
Install a new PS-735/756 board by reversing the steps of
removal.
1-2-3. Replacing the Lithium Battery (CR2032)
A lithium battery is mounted on the CA-72 board for
driving internal watch while the power is turned off.
Replace the battery before the replacement time shown
below comes.
Status of usage of this machine Replacement time
The battery has never been Non power-on period of
replaced since purchase of this machine is shorter
than
this machine. approx 3 years.
(Because consumption of
battery has started already
at the time of purchase of
this machine.)
The battery is replaced by the Non power-on period of this
new battery last time. machine is approx. 3 years.
This machine has been used Period of usage of thiswith
always power-on. machine is shorter than 5
years.
(Because the battery life is
5 years and the consumption
of the battery has already
started at the time of
purchase of this machine.)
Use the specified battery in the case of replacement.
Ref. No. Address Item
BT200 (A-2) Lithium battery (CR2032): !1-528-174-31
Replacement Procedure
n
When replacing the battery, do not touch the battery
directly as this may corrode electrode.
Start
Replace the battery
Set the clock
*1, *2
(Refer to the System Setup Manual, Section 2-4.)
End
n
*1 : When replacing the battery, a battery error message
(“E.50” “BT”) may appear. This can be cleared by
setting the clock again.
*2 : If the battery runs out, the clock data cannot be
retained correctly.
Switching regulator
PSW3 x12
PSW
3 x6
PSW3 x6
PS-735/756 board
Plate nut
CN101
Plug holder (A)
Insulating sheet

1-3 (E)
BKS-R6010 MM
SONY ROUTING SYSTEM BKS-6010 V1.00 STATION NUMBER 5
ITEM
ROM CHECK SUM AEDA
S-BUS LINK TERMINATE OK
REAL TIME CLOCK OK
STARTED
SONY ROUTING SYSTEM SETUP MENU BKS-R6010 V1.00 STATION NUMBER 2
c+E: MENU c+D:RTN
DISPLAY UNIT STATUS
UNIT PREFERENCE
UBOOT SYS IP-ADDRESS MULTICAST SERIAL
1.00 V0.01 172.16.2.46 225.0.0.4 10001
REMOTE1 STATUS
ID BAUDRATE
A 46 312kbps
PRIMARY STATION
S-BUS F OK
ETHER F OK (Delegate)
6. Send the application program data from the terminal
software to BKS-R6010.
7. After transmission is completed, the data is written in
the flash memory and the BKS-R6010 will automati-
cally restarts.
8. Exit the terminal software.
n
After data transmission is completed, do not perform
any panel operation until the BKS-R6010 automatical-
ly restarts.
9. Check that the BKS-R6010 has restarted correctly.
Checking after upgrading the software version
The software version can be checked from the terminal
menu connected to the primary station.
n
Refer to the SYSTEM SETUP MANUAL for details of the
terminal menu.
Procedure
1. Display the menu screen of the primary station by
pressing [Ctrl] _[X] keys on the system status screen.
2. Select “R: CALL SECONDARY STATION”.
3. Enter the station ID of the upgraded BKS-R6010 and
press [ENTER].
4. Select “V: DISPLAY UNIT STATUS”.
5. Check that the version number displayed on the screen
is the same as that of the downloaded software.
Refer to “V: DISPLAY UNIT STATUS” in the “2-4.
Setting Items of the Secondary Station” of the SYS-
TEM SETUP MANUAL for details.
1-3. Upgrading the Application Software
Version
Preparation
1. Check that the network cable is connected to the
network connector NETWORK of BKS-R6010 and
the Ethernet switch is connected. (Fig.1)
Fig.1
2. Configure the network parameters of the personal
computer used for upgrading software versions so that
it can connect to BKS-R6010.
m
.Check that the subnet mask matches that of BKS-
R6010.
.Check that the higher 3 bits of the IP address
matches those of BKS-R6010.
3. Check the IP address of BKS-R6010.
The IP address can be checked by using the terminal
menu “V: DISPLAY UNIT STATUS” of the second-
ary station or using the status indicator of BKS-R6010.
Refer to the SYSTEM SETUP MANUAL and IN-
STALLATION MANUAL for the terminal menu of the
secondary station and the status indicator, respectively.
Procedure
1. Turn on the power of the personal computer.
2. Copy the application program data to the personal
computer.
3. Start the terminal software of the personal computer.
4. Connect (Link) the personal computer to BKS-R6010
via Ethernet.
Set the same IP address as that of BKS-R6010 for the
TCP/IP of the terminal software and set the port
number to “1001”.
When checking the IP address of BKS-R6010, refer to
“2-2. Checking Equipment Status” of the INSTALLA-
TION MANUAL.
5. Check that a starting screen is displayed in the termi-
nal menu.
Ethernet Switch
BKS-R6010 PC
NETWORK
Network Cable
(straight)
Network Cable
(straight)
Example of screen
6. Press [Ctrl] _[D] to return to the menu screen of the
primary station.
7. Press [Ctrl] _[X] to return to the system status screen.

1-4 (E) BKS-R6010 MM
1-4. Writing the PLD Data
This section describes how to upgrade the PLD version of
each board using the PLD download tool.
Equipment required
.A personal computer equipped with the USB port (For
the target OS, refer to the operation manual supplied
with the PLD Download Tool.)
.PLD Download Tool Ver 3.X or later (for USB port)
(J-7120-220-A)
Connection
1. Connect the PLD Download Tool to the USB port of
the personal computer.
2. Connect the cable (10-pin connector) coming from the
PLD Download Tool to the following connector on the
target board.
Target board Ref. No. Project file No.
CA-72 Board CN800 E-000-004-00-xx
KY-627 Board CN900 E-000-004-01-xx
n
No setup is required in board.
Downloading
1. Start up the PLD Download Tool Software on the
personal computer.
After reading data for upgrading the PLD version,
write the data and confirm that is correctly written.
n
For details of the operation, refer to the operation
manual of the PLD Download Tool
2. Upon completion of downloading, turn off the main
power of the BKS-R6010 once.
1-5. Cleaning for Remote Control Panel
Wipe the remote control panel, switches, and LCD with a
dried cleaning cloth.
Use a cleaning cloth moistened with water or lukewarm
water for persistent stain.
n
Be sure to use a wrung cloth for wiping the remote control
panel since water droplet causes the malfunction.
Do not use any chemical, solvent, or cleaner, or wipe it
hard to avoid damaging it.
1-6. Circuit-Protection Part
This unit is equipped with the positive characteristics
thermister (s) (power thermister) as the circuit protection
element. The positive characteristics thermister limits the
electric current flowing through the circuit as the internal
resistance increases when an excessive current flows or
when the ambient temperature increases.
If the positive characteristics thermister works, turn off the
main power of the unit and inspect the internal circuit of
this unit. After the cause of the trouble is re-moved, turn on
the main power back again. The unit works normally.
It takes about one minute to cool down the positive charac-
teristics thermister after the main power is turned off.
Board Ref. No. Address Part No.
CA-72 THP1 E-3 (A side) !1-802-063-21
CA-72 THP2 E-3 (A side) !1-802-063-21
1-7. Unleaded Solder
Boards requiring use of unleaded solder are printed with a
lead free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come
printed with the lead free mark due to their particular size.)
: LEAD FREE MARK
m
.Be sure to use the unleaded solder for the printed circuit
board printed with the lead free mark.
.The unleaded solder melts at a temperature about 40 dC
higher than the ordinary solder, therefore, it is recom-
mended to use the soldering iron having a temperature
regulator.
.The ordinary soldering iron can be used but the iron tip
has to be applied to the solder joint for a slightly longer
time. The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful.

1-5 (E)
BKS-R6010 MM
1-8. Downloading the Font Data
<BKS-R6010 (Ver.2.00 or higher)>
The BKS-R6010 of ver. 2.00 or higher supports the
multilingual display. Make sure that the font data corre-
sponding to the language must be downloaded to display
the characters correctly. The font data currently available
are as follows.
Font data type Supported language
TYPE1 English, Japanese
TYPE2 English, Chinese (Simplified Chinese)
Download the font data corresponding to the language
from the designated download site.
The font data are also stored in the CD-ROM supplied with
the IXS-6600-C/IXS-6700-C.
n
The type1 font data is installed as the factory default
setting. This font data corresponds to the English and
Japanese areas.
Preparation
1. Check that the network cable is connected to the
network connecter NETWORK of the unit and
connected to the Ethernet Switch. (Fig. 1)
2. Configure the network setting of the PC used to
download the data to the one that can be connected to
the unit.
m
.Check if the subnet mask corresponds to that of the
unit.
.Check if the upper three digits of the IP address
corresponds to those of the unit.
3. Check the IP address of the unit.
The IP address can be checked in the secondary station
terminal menu “V: DISPLAY UNIT STATUS” or
with the status indicator of the unit.
For the secondary station terminal menu, refer to the
system setup manual, and for the status indicator, refer
to the installation manual.
SONY ROUTING SYSTEM BKS-6010 V2.00 STATION NUMBER 2
ITEM
ROM CHECK SUM AEDA
S-BUS LINK TERMINATE OK
REAL TIME CLOCK OK
STARTED
Standard operation time
The standard time for each operation is as follows.
Trans Writing to Restarting Total
ferring the flash
data memory
About 6 About 3 About 1 About 10
minutes minutes minutes minutes
n
The time shown above is just a standard. The time may
differ depending on the working environment.
Procedure
1. Turn on the power of the PC.
2. Copy the font data to be downloaded to the PC.
3. Start the terminal software on the PC.
4. Connect (link) the PC to the unit via Ethernet.
Set the same IP address as that of the unit for the TCP/
IP of the terminal software, and set the Port number to
1001.
For checking the IP address of the unit, refer to "2-2.
Checking Equipment Status” of the Installation
manual.
5. Check that the startup screen is displayed in the
terminal menu.
6. Send the font data from the terminal software to the
unit.
7. When the data is written to the flash memory after the
data is sent, the unit automatically restarts.
n
While writing the data to the flash memory (for about
3 minutes) after transferring the data, all LCD displays
on the panel turn blue. This is not a failure.
Do not turn off the power while all the LCD displays
on the panel light in blue (the data is written to the
flash memory).
8. Exit the terminal software.
9. Check that the unit restarts normally.
Ethernet Switch
BKS-R6010 PC
NETWORK
Network cable
(straight)
Fig. 1
Network cable
(straight)

1-6 (E) BKS-R6010 MM
Checking after downloading
Check the type and version of the font data in the terminal
menu connected to the primary station.
n
For details about the terminal menu, refer to the system
setup manual.
Procedure
1. Simultaneously press [Ctrl] and [X] in the system
status screen to display the menu of the primary
station.
2. Select “R : CALL SECONDARY SATATION”.
3. Enter the station ID of the unit that has been upgraded,
and press [ENTER].
4. Select “V : DISPLAY UNIT STATUS”.
5. Check that the type and version are the same as those
of the downloaded font data.
For details about the display items, refer to “V :
DISPLAY UNIT STATUS” in “2-4. Setting Items of
the Secondary Station (BKS-R6010)” of the System
Setup Manual
Display screen example
6. Simultaneously press [Ctrl] and [D] to return to the
menu of the primary station.
7. Simultaneously press [Ctrl] and [X] to return to the
system status screen.
SONY ROUTING SYSTEM SETUP MENU BKS-R6010 V2.00 STATION NUMBER 2
c+E: MENU c+D:RTN
DISPLAY UNIT STATUS
UNIT PREFERENCE
UBOOT SYS IP-ADDRESS MULTICAST SERIAL
V1.00 V2.00 43.1.32.222 123.123.123.123 12345
REMOTE1 STATUS
ID BAUDRATE
A 2 312kbps
B 1 312kbps
PRIMARY STATION
S-BUS : OK
ETHER : OK (Delegate)
FONT
TYPE1 V1.00
Check the type and version of the font data.

BKS-R6010 MM 2-1
2-1. Notes on Repair Parts
1. Safety Related Components Warning
w
Components marked !are critical to safe operation.
Therefore, specified parts should be used in the case of
replacement.
2. Standardization of Parts
Some repair parts supplied by Sony differ from those
used for the unit. These are because of parts common-
ality and improvement.
3. Stock of Parts
Parts marked with “o” at SP (Supply Code) column of
the spare parts list may not be stocked. Therefore, the
delivery date will be delayed.
4. Harness
Harnesses with no part number are not registered as
spare parts.
Section 2
Spare Parts
2-1.

2-2 BKS-R6010 MM
No. Part No. SP Description
1 A-1052-994-B s CASE (12) ASSY, SW
2 A-1246-059-A s MOUNTED CIRCUIT BOARD, KY-627
3 A-1359-016-A s LCD SW ASSY
4 ! 1-802-550-11 s DISPLAY PANEL, LIQUID CRYSTAL
5 2-236-956-02 s SCREW, STEP
6 3-215-640-01 s BRACKET, ORNAMENT
7 3-215-641-01 s BRACKET (1U), RACK MOUNT
8 3-268-104-01 s KNOB, VOLUME
9 3-650-537-01 o WASHER
10 3-853-740-02 s CAP(12)
11 3-853-743-03 s PLATE,DIFFUSION(12)
12 3-624-821-01 s +PSW 3X6 (CU, NI)
7-682-547-09 s SCREW +B 3X6
7-682-561-04 s SCREW +B 4X8
FRONT PANEL ASSEMBLY
2-2. Exploded Views
SW-1377
board
10
3
3
3
3
11
10
11
9
7
8
6
9
7
2
4
5
5
5
6
1
1
CPU BOX (HIGH)
ASSEMBLY
B3 x6
B4 x8
B4 x8
B4 x8 B4 x8
B3 x6
12
12
12
12
12
12
12
12

2-3
BKS-R6010 MM
No. Part No. SP Description
101 A-1246-057-A s MOUNTED CIRCUIT BOARD, CPU-417
102 A-1246-058-A s MOUNTED CIRCUIT BOARD, CA-72
103 A-1256-255-A s MOUNTED CIRCUIT BOARD, PS-735 (Serial No.10001 - 10060)
A-1512-243-A s MOUNTED CIRCUIT BOARD, PS-756 (Serial No.10061 - )
104 X-2068-004-1 s TERMINAL ASSY
105 ! 1-528-174-31 s BATTERY, LITHIUM (CR2032 TYPE)
106 2-068-008-01 s WASHER
107 2-280-622-22 s SUPPORT (M3X10), HEXAGON
108 2-580-595-01 s SCREW, +PSW M3X12
109 2-990-241-02 s HOLDER (A), PLUG
110 3-637-901-02 s SCREW M2.6X5
111 3-624-821-01 s SCREW +PSW 3X6 (CU, NI)
7-685-146-11 s SCREW +P 3X8 TYPE2 NON-SLIT
CPU BOX (HIGH) ASSEMBLY
101
103
105
102
110
109
104
106
108
107
P3 x8
111
111
111
111
111
111

2-4 BKS-R6010 MM
2-3. Electrical Parts List
------------------------
CA-72 BOARD (Suffix -13)
------------------------
Ref. No.
or Q’ty Part No. SP Description
1pc A-1246-058-A s MOUNTED CIRCUIT BOARD, CA-72
1pc 7-621-770-87 s SCREW +B 2.6X5
BT200 1-756-076-21 s HOLDER, LITHIUM BATTERY
C100 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C101 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C102 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C103 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C104 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C106 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C107 1-128-536-21 s CAP, CHIP ELECT 100MF
C108 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C109 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C110 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C203 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C204 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C206 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C207 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C301 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C302 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C303 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C304 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C305 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C307 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C308 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C310 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C313 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C314 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C315 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C317 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C318 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C326 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C327 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C401 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C402 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C403 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C404 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C405 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C406 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C407 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C408 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C409 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C410 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C411 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C412 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C413 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C414 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C415 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C416 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C417 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C418 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C419 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C420 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C421 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C501 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C503 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C505 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C507 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C509 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
(CA-72 BOARD (Suffix -13))
Ref. No.
or Q’ty Part No. SP Description
C511 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C513 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C515 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C601 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C603 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C605 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C607 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C609 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C611 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C613 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C615 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C701 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C703 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C704 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C805 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C820 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C901 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C902 1-164-854-81 s CAP, CHIP CERAMIC 15PF CH 1005
C903 1-164-854-81 s CAP, CHIP CERAMIC 15PF CH 1005
C904 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225
C905 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225
C906 1-107-819-81 s CAP,CHIP CERAMIC 22000PF B1005
C907 1-107-819-81 s CAP,CHIP CERAMIC 22000PF B1005
C908 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C909 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C910 1-100-159-91 s CAP, CERAMIC 22MF B (SMD) 3216
C911 1-100-159-91 s CAP, CERAMIC 22MF B (SMD) 3216
C912 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C913 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C914 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C915 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C916 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C917 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C950 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C951 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C952 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C953 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C954 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C955 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1000 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005
C1001 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005
C1002 1-164-874-81 s CAP,CHIP CERAMIC 100PF CH 1005
C1003 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005
C1004 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005
C1005 1-164-874-81 s CAP,CHIP CERAMIC 100PF CH 1005
C1006 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005
C1007 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005
C1009 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1010 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1011 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1012 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1200 1-135-348-21 s CAP, ELECT 150MF (10X8)
C1201 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1204 1-164-939-81 s CAP, CHIPCERAMIC 2200PF B 1005
C1205 1-164-862-81 s CAP, CHIP CERAMIC 33PF CH 1005
C1206 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1207 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1208 1-164-939-81 s CAP, CHIPCERAMIC 2200PF B 1005
C1214 1-119-923-81 s CAP, CERAMIC 0.047MF B 1005

2-5
BKS-R6010 MM
(CA-72 BOARD (Suffix -13))
Ref. No.
or Q’ty Part No. SP Description
C1215 1-107-819-81 s CAP,CHIP CERAMIC 22000PF B1005
C1216 1-164-850-81 s CAP, CHIP CERAMIC 10PF CH 1005
C1218 1-164-850-81 s CAP, CHIP CERAMIC 10PF CH 1005
C1222 1-164-939-81 s CAP, CHIPCERAMIC 2200PF B 1005
C1224 1-164-939-81 s CAP, CHIPCERAMIC 2200PF B 1005
C1225 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1226 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1228 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225
C1230 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1234 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1236 1-135-960-91 s CAP, CHIP CERAMIC 10MF B(3225)
C1238 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225
C1239 1-100-055-21 s CAP, CHIP CERAMIC 22MF B 3225
C1244 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1245 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1250 1-165-989-91 s CAP, CERAMIC 10MF (2012)
C1251 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1252 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1253 1-119-923-81 s CAP, CERAMIC 0.047MF B 1005
C1254 1-119-923-81 s CAP, CERAMIC 0.047MF B 1005
C1256 1-164-874-81 s CAP,CHIP CERAMIC 100PF CH 1005
C1257 1-100-581-81 s CAP,CHIP CERAMIC0.0047MF B1005
C1258 1-164-939-81 s CAP, CHIPCERAMIC 2200PF B 1005
C1262 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1263 1-100-421-21 s CAP, ELECT 220MF (6.3X5.9)
C1264 1-100-421-21 s CAP, ELECT 220MF (6.3X5.9)
C1265 1-127-710-21 s CAP, CHIP ELECT 47MF (7343)
C1266 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1267 1-165-989-91 s CAP, CERAMIC 10MF (2012)
C1400 1-100-159-91 s CAP, CERAMIC 22MF B (SMD) 3216
C1401 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1402 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1403 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1404 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1405 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1406 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1407 1-100-159-91 s CAP, CERAMIC 22MF B (SMD) 3216
C1408 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1409 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1410 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1411 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1412 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1413 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1414 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1415 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1416 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1417 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1418 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1419 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1420 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1421 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1422 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1423 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1424 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1425 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1426 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1427 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1428 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1429 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
(CA-72 BOARD (Suffix -13))
Ref. No.
or Q’ty Part No. SP Description
C1430 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1431 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1432 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1433 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005
C1500 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1501 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1502 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1503 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1504 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
C1505 1-100-505-91 s CAP, CERAMIC 0.1MF C (1005)
CN100 1-815-187-11 s JACK, MODULAR
CN102 1-573-566-11 s CONNECTOR, D-SUB(ANGLE TYPE)9P
CN103 1-565-388-11 o CONNECTOR, D-SUB 9P
CN104 1-816-587-21 s PIN, CONNECTOR (PC BOARD) 15P
CN105 1-794-822-11 s CONNECTOR, COAXIAL (BNC TYPE)
CN106 1-816-587-21 s PIN, CONNECTOR (PC BOARD) 15P
CN201 1-764-087-21 s PIN, CONNECTOR (PC BOARD) 14P
CN800 1-784-254-21 s CONNECTOR 10P
CN1000 1-793-324-11 o CONNECTOR, COAXIAL (BNC TYPE)
CN1201 1-816-587-21 s PIN, CONNECTOR (PC BOARD) 15P
CN1401 1-770-625-21 s PIN, CONNECTOR 8P
D101 8-719-069-55 s DIODE UDZSNPTE-175.6B
D102 8-719-069-55 s DIODE UDZSNPTE-175.6B
D104 8-719-069-55 s DIODE UDZSNPTE-175.6B
D105 8-719-069-55 s DIODE UDZSNPTE-175.6B
D203 8-719-056-48 s DIODE 1SS388(TPL3)
D800 8-719-074-31 s DIODE CL-196YG-CD-T
D801 8-719-074-31 s DIODE CL-196YG-CD-T
D802 8-719-074-31 s DIODE CL-196YG-CD-T
D803 8-719-074-31 s DIODE CL-196YG-CD-T
D804 8-719-074-31 s DIODE CL-196YG-CD-T
D805 8-719-074-31 s DIODE CL-196YG-CD-T
D806 8-719-074-31 s DIODE CL-196YG-CD-T
D807 8-719-074-31 s DIODE CL-196YG-CD-T
D808 8-719-074-31 s DIODE CL-196YG-CD-T
D809 8-719-074-31 s DIODE CL-196YG-CD-T
D900 8-719-056-48 s DIODE 1SS388(TPL3)
D901 8-719-056-48 s DIODE 1SS388(TPL3)
D1000 8-719-016-87 s DIODE 02DZ2.2-TPH3
D1001 8-719-016-87 s DIODE 02DZ2.2-TPH3
D1200 8-719-065-59 s DIODE MBR0530T1
D1201 8-719-065-59 s DIODE MBR0530T1
D1204 8-719-072-43 s DIODE RB050L-40TE25
D1205 8-719-072-43 s DIODE RB050L-40TE25
E1200 1-535-877-22 s CHIP, CHECKER
E1201 1-535-877-22 s CHIP, CHECKER
E1202 1-535-877-22 s CHIP, CHECKER
FB900 1-469-094-21 s FERRITE, EMI (SMD) (1608)
FB901 1-469-094-21 s FERRITE, EMI (SMD) (1608)
FB1000 1-469-094-21 s FERRITE, EMI (SMD) (1608)
FB1001 1-469-094-21 s FERRITE, EMI (SMD) (1608)
IC100 6-701-098-11 s IC THC63LVDM83R-T
IC102 6-702-547-11 s IC SN65LVDS2DR
IC103 6-702-546-11 s IC SN65LVDS1DR
IC201 6-710-018-01 s IC CAT24C02WI-GT3
IC202 6-700-108-01 s IC RV5C387A-E2-FB
IC203 6-710-018-01 s IC CAT24C02WI-GT3

2-6 BKS-R6010 MM
(CA-72 BOARD (Suffix -13))
Ref. No.
or Q’ty Part No. SP Description
IC205 6-708-016-01 s IC LM75BIMX-3/NOPB
IC302 6-708-324-01 s IC R3112N301A-TR-FA
IC303 8-759-437-39 s IC MB3771PF-ER
IC304 6-704-567-01 s IC R3112N451A-TR-FA
IC305 6-704-642-01 s IC R3112N131A-TR-FA
IC309 8-759-437-39 s IC MB3771PF-ER
IC310 6-707-869-01 s IC TC74VHC14FT(EKJ)
IC311 6-707-869-01 s IC TC74VHC14FT(EKJ)
IC312 8-759-675-47 s IC SN74LVC04APWR
IC500 8-759-392-81 s IC SN74LVC16245ADGGR
IC501 8-759-392-81 s IC SN74LVC16245ADGGR
IC600 8-759-392-81 s IC SN74LVC16245ADGGR
IC601 8-759-392-81 s IC SN74LVC16245ADGGR
IC701 6-709-716-01 s IC S29GL512N10TFI020
IC801 6-707-874-01 s IC TC74VHC244FT(EKJ)
IC901 8-759-327-14 s IC TL712CPSR
IC902 8-759-327-14 s IC TL712CPSR
IC912 6-707-883-01 s IC TC74VHCT00AFT(EKJ)
IC913 6-710-750-01 s IC LM393PSRG4
IC914 6-705-514-01 s IC MAX3222IPWR
IC952 8-759-396-99 s IC MAX489CSD+TG068
IC953 8-759-396-99 s IC MAX489CSD+TG068
IC956 6-707-884-01 s IC TC74VHCT04AFT(EKJ)
IC957 6-707-863-01 s IC TC74VHC08FT(EKJ)
IC958 6-707-884-01 s IC TC74VHCT04AFT(EKJ)
IC959 6-707-861-01 s IC TC74VHC04FT(EKJ)
IC1001 8-759-592-44 s IC TC7SZ04FU(TE85R)
IC1002 6-706-484-01 s IC TC7SH04FU(T5RSOYJF)
IC1003 6-702-231-01 s IC LMH6642MFX/NOPB
IC1004 6-702-231-01 s IC LMH6642MFX/NOPB
IC1200 6-702-510-01 s IC TPS5120DBTRG4
IC1250 6-703-721-01 s IC TPS54310PWPR
IC1500 6-701-874-01 s IC IDT71V016SA15PHG-TL
IC1501 6-701-874-01 s IC IDT71V016SA15PHG-TL
L1200 1-419-491-21 s COIL, CHOKE 10UH
L1201 1-419-491-21 s COIL, CHOKE 10UH
L1202 1-419-491-21 s COIL, CHOKE 10UH
L1203 1-419-491-21 s COIL, CHOKE 10UH
L1250 1-416-344-21 s COIL, CHOKE 10UH
LF200 1-456-826-11 s COIL, COMMON MODE CHOKE
LF201 1-456-826-11 s COIL, COMMON MODE CHOKE
LF202 1-456-826-11 s COIL, COMMON MODE CHOKE
LF203 1-456-826-11 s COIL, COMMON MODE CHOKE
LF204 1-456-826-11 s COIL, COMMON MODE CHOKE
LF205 1-456-826-11 s COIL, COMMON MODE CHOKE
LF206 1-456-826-11 s COIL, COMMON MODE CHOKE
Q200 8-729-929-09 s TRANSISTOR DTC123JE-TL
Q201 8-729-928-25 s TRANSISTOR 2SA1774TL-QR
Q300 8-729-929-09 s TRANSISTOR DTC123JE-TL
Q800 8-729-929-09 s TRANSISTOR DTC123JE-TL
Q902 8-729-230-61 s TRANSISTOR 2SA1586YG-TE85L
Q903 8-729-230-61 s TRANSISTOR 2SA1586YG-TE85L
Q904 8-729-142-11 s TRANSISTOR 2SA1226-T1E3E4
Q905 8-729-142-11 s TRANSISTOR 2SA1226-T1E3E4
Q906 8-729-929-09 s TRANSISTOR DTC123JE-TL
Q907 8-729-929-09 s TRANSISTOR DTC123JE-TL
Q950 8-729-920-75 s TRANSISTOR 2SC2412K-T-146-QR
Q951 8-729-920-75 s TRANSISTOR 2SC2412K-T-146-QR
(CA-72 BOARD (Suffix -13))
Ref. No.
or Q’ty Part No. SP Description
Q952 8-729-920-75 s TRANSISTOR 2SC2412K-T-146-QR
Q953 8-729-920-75 s TRANSISTOR 2SC2412K-T-146-QR
Q1200 6-551-261-01 s TRANSISTOR SI4804BDY-T1
Q1201 6-551-261-01 s TRANSISTOR SI4804BDY-T1
R13 1-208-927-81 s RES, CHIP 47K (1005)
R14 1-208-927-81 s RES, CHIP 47K (1005)
R15 1-208-927-81 s RES, CHIP 47K (1005)
R100 1-208-927-81 s RES, CHIP 47K (1005)
R101 1-208-927-81 s RES, CHIP 47K (1005)
R102 1-208-863-81 s RES, CHIP 100 (1005)
R103 1-208-871-81 s RES, CHIP 220 (1005)
R104 1-208-871-81 s RES, CHIP 220 (1005)
R106 1-208-863-81 s RES, CHIP 100 (1005)
R107 1-218-990-81 s CONDUCTOR, CHIP (1005)
R108 1-218-990-81 s CONDUCTOR, CHIP (1005)
R109 1-218-990-81 s CONDUCTOR, CHIP (1005)
R110 1-218-990-81 s CONDUCTOR, CHIP (1005)
R111 1-208-927-81 s RES, CHIP 47K (1005)
R114 1-218-990-81 s CONDUCTOR, CHIP (1005)
R116 1-218-990-81 s CONDUCTOR, CHIP (1005)
R117 1-218-990-81 s CONDUCTOR, CHIP (1005)
R118 1-218-990-81 s CONDUCTOR, CHIP (1005)
R119 1-218-990-81 s CONDUCTOR, CHIP (1005)
R213 1-208-895-81 s RES, CHIP 2.2K (1005)
R217 1-208-887-81 s RES, CHIP 1.0K (1005)
R218 1-208-863-81 s RES, CHIP 100 (1005)
R222 1-208-855-81 s RES, CHIP 47 (1005)
R223 1-208-855-81 s RES, CHIP 47 (1005)
R224 1-208-855-81 s RES, CHIP 47 (1005)
R225 1-208-855-81 s RES, CHIP 47 (1005)
R226 1-220-870-81 s RES, CHIP 10 (1005)
R227 1-220-870-81 s RES, CHIP 10 (1005)
R228 1-218-990-81 s CONDUCTOR, CHIP (1005)
R240 1-208-911-81 s RES, CHIP 10K (1005)
R241 1-208-911-81 s RES, CHIP 10K (1005)
R242 1-208-911-81 s RES, CHIP 10K (1005)
R243 1-208-887-81 s RES, CHIP 1.0K (1005)
R244 1-220-878-81 s RES, CHIP 22 (1005)
R245 1-220-878-81 s RES, CHIP 22 (1005)
R246 1-220-878-81 s RES, CHIP 22 (1005)
R247 1-218-990-81 s CONDUCTOR, CHIP (1005)
R248 1-208-927-81 s RES, CHIP 47K (1005)
R249 1-208-927-81 s RES, CHIP 47K (1005)
R250 1-208-927-81 s RES, CHIP 47K (1005)
R251 1-218-990-81 s CONDUCTOR, CHIP (1005)
R252 1-218-990-81 s CONDUCTOR, CHIP (1005)
R253 1-218-990-81 s CONDUCTOR, CHIP (1005)
R254 1-218-990-81 s CONDUCTOR, CHIP (1005)
R255 1-218-990-81 s CONDUCTOR, CHIP (1005)
R303 1-208-943-81 s RES, CHIP 220K (1005)
R304 1-208-927-81 s RES, CHIP 47K (1005)
R305 1-208-927-81 s RES, CHIP 47K (1005)
R306 1-208-903-81 s RES, CHIP 4.7K (1005)
R307 1-208-903-81 s RES, CHIP 4.7K (1005)
R308 1-208-943-81 s RES, CHIP 220K (1005)
R309 1-208-927-81 s RES, CHIP 47K (1005)
R310 1-208-927-81 s RES, CHIP 47K (1005)
R311 1-208-903-81 s RES, CHIP 4.7K (1005)
R315 1-208-927-81 s RES, CHIP 47K (1005)