Sony MKS-9011A User manual

CENTER CONTROL PANEL PACK
CCP-9000A-C
INSTALLATION MANUAL
2nd Edition
HK-PSU11
MKS-8011A
MKS-8031ATB
MKS-8032A
MKS-8033A
MKS-8035A
MKS-8041
MKS-8075A
MKS-9011A
1 M/E CONTROL PANEL
MKS-9012A
2 M/E CONTROL PANEL
SWC-5002
SWC-5005
SWC-5010

CCP-9000A
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
HK-PSU11 Serial No. 10001 and Higher
MKS-8011A Serial No. 10001 and Higher
MKS-8031ATB Serial No. 10001 and Higher
MKS-8032A Serial No. 10001 and Higher
MKS-8033A Serial No. 10001 and Higher
MKS-8035A Serial No. 10001 and Higher
MKS-8041 Serial No. 10001 and Higher
MKS-8075A Serial No. 10001 and Higher
MKS-9011A Serial No. 10001 and Higher
MKS-9012A Serial No. 20001 and Higher
SWC-5002 Serial No. 10001 and Higher
SWC-5005 Serial No. 10001 and Higher
SWC-5010 Serial No. 10001 and Higher

CCP-9000A
WARNING
This unit has no power switch.
When installing the unit, incorporate a readily
accessible disconnect device in the fixed wiring, or
connect the power cord to a socket-outlet which must be
provided near the unit and easily accessible, so that the
user can turn off the power in case a fault should occur.
WARNUNG
Dieses Gerät hat keinen Netzschalter.
Beim Einbau des Geräts ist daher im Festkabel ein
leicht zugänglicher Unterbrecher einzufügen, oder das
Netzkabel mu
ß mit einer in der Nähe des Geräts
befindlichen, leicht zugänglichen Wandsteckdose
verbunden werden, damit sich bei einer
Funktionsstörung die Stromversorgung zum Gerät
jederzeit unterbrechen lä
ß t.
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to the
following ports.
: PERIPH (peripheral) connector
: CTRL (control) connector
: DATA connector
Follow the instructions for the above ports.
For the customers in the Netherlands
Voor de klanten in Nederland
Hoe u de batterijen moet verwijderen, leest u in de
Onderhoudshandleiding.
Gooi de batterij niet weg maar lever deze in als klein
chemisch afval (KCA).
Für Kunden in Deutschland
Entsorgungshinweis: Bitte werfen Sie nur entladene
Batterien in die Sammelboxen beim Handel oder den
Kommunen. Entladen sind Batterien in der Regel dann,
wenn das Gerät abschaltet und signalisiert “Batterie
leer”oder nach längerer Gebrauchsdauer der Batterien
“nicht mehr einwandfrei funktioniert”. Um
sicherzugehen, kleben Sie die Batteriepole z.B. mit
einem Klebestreifen ab oder geben Sie die Batterien
einzeln in einen Plastikbeutel.
1 (P)

1
CCP-9000A
Table of Contents
Manual Structure
Purpose of this manual .............................................................................................. 2
Related manuals ......................................................................................................... 2
Contents ..................................................................................................................... 2
1. Installation
1-1. Operating Environment (Common) ............................................................ 1-1
1-2. Power Supply .............................................................................................. 1-1
1-3. Installation Space ........................................................................................ 1-2
1-3-1. External Dimensions .................................................................. 1-2
1-3-2. Installation Space ....................................................................... 1-5
1-4. Installing on the Control Console ............................................................... 1-7
1-4-1. MKS-9011A ............................................................................... 1-7
1-4-2. MKS-9012A ............................................................................... 1-8
1-5. Installing the Menu Panel.......................................................................... 1-10
1-6. Installation of Options ............................................................................... 1-10
1-6-1. Installing HK-PSU11 ............................................................... 1-11
1-6-2. Installation to MKS-8075A (Extension Adaptor) .................... 1-12
1-6-3. How to Connect the MKS-8075A ............................................ 1-13
1-6-4. How to Connect the Cables ...................................................... 1-17
1-6-5. Rack Mounting the MKS-8075A (Extension Adaptor) ........... 1-17
1-7. Matching Connectors and Cables .............................................................. 1-19
1-8. Input/Output Signals of Connectors .......................................................... 1-20
1-9. Description of On-board Switches and LEDs ........................................... 1-22
1-10. System Connection.................................................................................... 1-24
1-10-1. System Connection of the MVS-8000A Series ........................ 1-24
1-10-2. Connecting the Center Control Panel ....................................... 1-25
2. Service Overview
2-1. Troubleshooting .......................................................................................... 2-1
2-1-1. Center Control Panel MKS-9011A/9012A ................................ 2-1
2-1-2. Menu Panel MKS-8011A ........................................................... 2-1
2-2. Periodic Inspection and Maintenance ......................................................... 2-2
2-2-1. Cleaning ..................................................................................... 2-2
2-3. About the Data Backup Capacitor ............................................................... 2-3
2-4. Removing/Reinstalling Front Panel ............................................................ 2-3

2CCP-9000A
Purpose of this manual
This manual is the installation manual of Center Control Panel Pack CCP-9000A-C
and the optional units.
This manual is intended for use by trained system and service engineers, and
describes the information on installing the CCP-9000A-C.
Related manuals
The following manuals are prepared for CCP-9000A-C and the optional units.
..
..
.Operation Manual (Supplied with CCP-9000A-C)
This manual describes the overview, system connection example and specifica-
tions of options of CCP-9000A-C.
..
..
.User’s Guide (Volume 1, Volume 2) (Supplied with CCP-9000A-C)
This manual describes the application and operation of CCP-9000A-C.
..
..
.Maintenance Manual (Available on request)
This manual describes the detailed service information.
If this manual is required, please contact your local Sony Sales Office/Service
Center.
Contents
This manual is organized by following sections.
Section 1 Installation
This section describes the operating environment, power supply, installation space,
installation of option, installing on the control console, connectors, input and output
signals of connectors, checking upon completion of installation, and system configu-
ration.
Section 2 Service Overview
This section describes the troubleshooting and periodic inspection and maintenance.
Manual Structure

1-1
CCP-9000A
For customers in the all European countries
1Power cord, 250 V 10 A (2.4 m) : !1-782-929-22
1
AC inlet
For customers in the U.S.A. and Canada
1Power cord, 125 V 10 A (2.4 m) : !1-557-377-11
AC inlet
1
Section 1
Installation
1-1. Operating Environment (Common)
Operating guaranteed temperature : +5 dC to +40 dC
Performance guaranteed temperature : +10 dC to +35 dC
Operating humidity : 10 % to 90 %
Storage temperature : _20 dC to +60 dC
Mass
MKS-9011A : Approx. 10.0 kg
MKS-9012A : Approx. 11.5 kg
MKS-8011A : Approx. 2.3 kg
MKS-8031ATB : Approx. 0.7 kg
MKS-8032A : Approx. 0.7 kg
MKS-8033A : Approx. 0.7 kg
MKS-8035A : Approx. 0.6 kg
MKS-8041 : Approx. 0.4 kg
MKS-8075A : Approx. 0.6 kg
Prohibited locations for installation
.Areas where the unit will be exposed to direct sunlight or
any other strong lights.
.Dusty areas
.Areas subject to vibration.
.Areas with strong electric or magnetic fields.
.Areas near heat sources.
.Areas where is subject to electrical noise.
.Areas subject to static electricity.
Ventilation
The inside of the MKS-9011A/9012A is cooled by a fan.
The power supply can be damaged if the exhaust vent (on
the rear) and air intake (on the front) are blocked or the fan
is stopped.
Therefore, leave a blank space of more than 10 cm in the
front and back of the MKS-9011A/9012A.
1-2. Power Supply
Power specifications
A switching regulator is used for the power supply of
MKS-9011A/9012A. A voltage within the range of 100 V
to 240 V can be used without changing the supply voltage.
Power requirements: AC 100 to 240 V ±10 %
Power frequency: 50/60 Hz
Current consumption
MKS-9011A: 1.0 - 0.6 A
MKS-9012A: 1.0 - 0.6 A
n
As the inrush current at turn-on is a maximum 21.5 A (at
100 V) /52 A (at 240 V), the capacity of the AC power
source must be commensurate with this load.
If the capacity of the AC power is not adequately large, the
AC power source breaker will operate or the unit will
abnormally operate.
Recommended power cord
This unit does not come with a power cord.
To get a power cord, please contact your local Sony Sales
Office/Service Center.
w
.Use the approved Power Cord (3-core mains lead)/
Appliance Connector/Plug with earthing-contacts that
conforms to the safety regulations of each country if
applicable.
.Use the Power Cord (3-core mains lead)/Appliance
Connector/Plug conforming to the proper ratings (Volt-
age, Ampere).
If you have questions on the use of the above Power Cord/
Appliance Connector/Plug, please contact your local Sony
Sales Office/Service Center.
w
.Never use an injured power cord.
.Plugging the power cord in the AC inlet, push as far as it
will go.

1-2 CCP-9000A
1-3. Installation Space
1-3-1. External Dimensions
Center control panel MKS-9012A
440
186.6 (4U +9)
142.6
119.4 7
260
26
18.2 442 (10U)
384
428
Unit : mm

1-3
CCP-9000A
Center control panel MKS-9011A/Menu panel MKS-8011A
MKS-8011A
MKS-9011A
220
160
213
424 46
440
175 (4U)
131
115.3
384
428
80.8 7
18.2
260
26
385.3 (9U)
324.2
Unit : mm

1-4 CCP-9000A
Extension adaptor MKS-8075A
263
79
85
91
396
Unit : mm
BANK
1
BANK
2
BANK
3
BANK
4
DSK3
DSK4
DSK3
ONONON
DSK2
ON
DSK1
DSK1
DSK4
DSK2
K-SS
STORE
TAKE TAKE TAKE TAKE
WIPE
MIX
DME
CUT
K-SS
SHIFT
UNDO

1-5
CCP-9000A
1-3-2. Installation Space
When the control panel is recessed into a control console or similar, make holes as shown below into the
control console with the following dimensions.
Center control panel MKS-9012A
450
481
465
177.8 311.2
446.7
39.4
6-M5
384.1
15
35
30 or more 30 or more
50 or more
120 or more
35
Unit : mm

1-6 CCP-9000A
Center control panel MKS-9011A
450
481
465
177.8 311.2
39.4
6-M5
402.7
15
35
30 or more 30 or more
50 or more
120 or more
35
Unit : mm

1-7
CCP-9000A
1-4. Installing on the Control Console
1-4-1. MKS-9011A
c
Be sure to install the MKS-9011A on the control console
by two or more persons. Installing it by one person may
cause backache.
The following parts supplied with the MKS-9011A are
required to install the MKS-9011A on the control console.
.Rack angle assembly (L) (R)
.Blank panel
.Screw B4 x12 (6)
.Screw B5 x8 (6)
.Screw B3 x6 (4)
1. Remove the six screws (B4 x6) of the MKS-9011A.
2. Remove the screws (B3 x4) from the rack angle
assembly (L) and the rack angle assembly (R) respec-
tively, and remove the rack angle cover (L) and the
rack angle cover (R).
3. Install the rack angle assembly (L) and the rack angle
assembly (R) on the MKS-9011A using the supplied
six screws (B4 x12).
4. Install the blank panel on the rack angle assemblies
with the supplied four screws (B3 x6).
B4 x6
B4 x6
MKS-9011A
B3 x4
B3 x4
Rack angle assembly (R)
Rack angle
assembly (L)
Rack angle
cover (L)
Rack angle cover (R)
B4 x12
B4 x12
MKS-9011A
Rack angle assembly (R)
Rack angle assembly (L)
B3 x6
B3 x6
Rack angle
assembly (R)
Blank panel
Rack angle
assembly (L)

1-8 CCP-9000A
5. Install the MKS-9011A on the control console with the
supplied six screws (B5 x8).
6. Install the rack angle cover (L) and the rack angle
cover (R) removed in step 2 on the rack angle assem-
bly (L) and the rack angle assembly (R) respectively.
n
Fit the covers on the rear side first and push them on
the front side lightly to install.
7. Tighten the rack angle cover (L) and the rack angle
cover (R) using the screws removed in step 2.
B5 x8
B5 x8
MKS-9011A
Control console
B3 x4
B3 x4
Rack angle
cover (L)
Rack angle
cover (R)
Rear side
Front side
Rack angle cover
B3 x4
B3 x4
B4 x6
B4 x6
MKS-9012A
Rack angle assembly (R)
Rack angle
assembly (L)
Rack angle
cover (L)
Rack angle cover (R)
1-4-2. MKS-9012A
c
Be sure to install the MKS-9012A on the control console
by two or more persons. Installing it by one person may
cause backache.
The following parts supplied with the MKS-9012A are
required to install the MKS-9012A on the control console.
.Rack angle assembly (L) (R)
.Blank panel (2)
.Screw B4 x12 (6)
.Screw B5 x8 (6)
.Screw B5 x20 (2)
1. Remove the six screws (B4 x6) of the MKS-9012A.
2. Remove the screws (B3 x4) from the rack angle
assembly (L) and the rack angle assembly (R) respec-
tively, and remove the rack angle cover (L) and the
rack angle cover (R).

1-9
CCP-9000A
B4 x12
B4 x12
MKS-9012A
Rack angle assembly (R)
Rack angle assembly (L)
3. Install the rack angle assembly (L) and the rack angle
assembly (R) on the MKS-9012A with the supplied six
screws (B4 x12) .
4. Install the MKS-9012A on the control console with the
supplied six screws (B5 x8).
B5 x8 B5 x8
MKS-9012A
Control console
5. Install the rack angle cover (L) and the rack angle
cover (R) removed in step 2 on the rack angle assem-
bly (L) and the rack angle assembly (R) respectively.
n
Fit the covers on the rear side first and push them on
the front side lightly to install.
6. Tighten the rack angle cover (L) and the rack angle
cover (R) using the screws removed in step 2.
7. Install the blank panels on the control console with the
supplied two screws (B5 x20).
B3 x4
B3 x4
B5 x20
B5 x20
Blank panel
Blank
panel
Rack angle
cover (L)
Rack angle
cover (R)
Rear side
Front side Rack angle cover

1-10 CCP-9000A
100 mm
75 mm 4-M4
4-M4
100 mm
75 mm
B3 x5
B3 x5
Adapter
Menu panel
50-pin cable
100 mm
75 mm
75 mm
Adapter
Monitor arm
B4 x8
B4 x8
100 mm
2. Install a commercially available monitor arm to the
adapter with the attached four screws (B4 x8).
n
For installation of monitor arm, refer to its operation
manual.
1-6. Installation of Options
The CCP-9000A-C system is comprised of the following
models according to the system to be used, and shipped
from the factory.
Model name
MKS-9011A 1 M/E CONTROL PANEL
MKS-9012A 2 M/E CONTROL PANEL
HK-PSU11 POWER SUPPLY UNIT
MKS-8011A MENU PANEL
MKS-8031ATB TRACK BALL MODULE
MKS-8032A DSK FADER MODULE
MKS-8033A UTILITY/SHOTBOX MODULE
MKS-8035A KEY CONTROL MODULE
MKS-8041 BLANK PANEL (1/2)
MKS-8075A EXTENSION ADAPTOR
SWC-5002 PANEL CABLE (2 m)
SWC-5005 PANEL CABLE (5 m)
SWC-5010 PANEL CABLE (10 m)
1-5. Installing the Menu Panel
The menu panel MKS-8011A can be installed to the
monitor arm compliant with VESA Standard using the
adapter supplied with CCP-9000A-C. See the dimensions
for installation below.
Adapter installation dimensions (compliant with
VESA Standard)
The following parts supplied with CCP-9000A-C are
required to install the menu panel.
n
Use the specified accessories when installing the menu
panel.
.Adapter
.50-pin cable
.Screws B3 x5 (4)
.Screws B4 x8 (4)
Installation
n
Connect the 50-pin cable attached to the menu panel, and
then perform the following steps.
1. Install the adapter to the menu panel with the attached
four screws (B3 x5).

1-11
CCP-9000A
1-6-1. Installing HK-PSU11
n
Before installing the HK-PSU11, be sure to unplug the
power cord, and confirm that the power is off.
1. Remove the screw which secures the release lever.
2. Turn the release lever counterclockwise.
B3 x6
Release lever
Release lever
3. Remove the blank panel.
n
Store the removed blank panel in a safe place.
4. Insert the HK-PSU11 securely along the guides.
5. Secure the release lever with the screw removed in
step 1 to lock the HK-PSU11.
Blank panel
HK-PSU11
HK-PSU11
HK-PSU11
Guide
Guide
Guide

1-12 CCP-9000A
1-6-2. Installation to MKS-8075A (Extension
Adaptor)
c
Be sure to disconnect the power cord before starting to
install modules.
If installation of modules is started with the POWER
switch left on, it may cause electrical shock damage
printed circuit boards.
Applicable modules
.MKS-8031ATB Track Ball Module
.MKS-8032A DKS Fader Module
.MKS-8033A Utility/Shotbox Module
.MKS-8035A Key Control Module
Installation
1. Remove the module cover on both sides of the opera-
tion module that you want to remove, as shown.
2. Loosen the four screws (with drop-safe) fixing the
operation module.
3. Remove the operation module by holding the two
screws on the sides of the operation module.
4. Fit the operation module that you want to install into
the position as described in step 3. Fix the operation
module by tightening the four screws (with drop-safe)
on both sides.
n
Removal
1. Remove the screw which secures the release lever.
2. Turn the release lever in either of the following
direction.
To remove the HK-PSU11 on slot A : 2
To remove the HK-PSU11 on slot B : 3
3. Remove the HK-PSU11.
B3 x6
Release lever
Slot A
Slot B
Slot A
Slot B

1-13
CCP-9000A
Ball cover
Track ball
MKS-8031ATB
5. Install the module covers.
n
For MKS-8031ATB, installation of the track ball is
required after the module is installed in steps 1 to 5.
Install the track ball by following the procedure below.
6. Rotate the ball cover counterclockwise to release the
lock. Then remove the ball cover.
7. Install the track ball and the ball cover.
8. Rotate the ball cover clockwise until it is locked.
234
Number of
connections
: Blank panel
(Using the blank panel)
1-6-3. How to Connect the MKS-8075A
Structure of MKS-8075A (Extension adaptor)
Adaptor case : 1
Screw (BV3 x10) : 4
Connecting plate A : 2
Connecting plate B : 1
Connecting plate C : 1
Panel cover (L) : 1
Panel cover (R) : 1
Cable (D-sub 50-pin): 1
m
.A maximum of three extension adaptors (maximum of
four when using the blank panel) can be connected either
horizontally, or vertically. (Up to two extension adaptors
can be connected horizontally.)
(For an example of connection, refer to Fig. 1.)
.There are three methods of vertical connection as
described below. (Refer to Fig. 2 (on page 1-16).)
Connection method A :
Install the extension adaptors on the panel so that
they have differences in height like a flight of steps
and with the same outside appearance as that of the
main panel.
Connection method B :
Install the extension adaptors flat on the panel with
no difference in height. (In such a case as installed
on tabletop)
Connection method C :
Install the extension adaptors in the rack. (Horizon-
tal connection is also required.)
.When extension adaptors are installed using both
horizontal and vertical connections, be sure to perform
the vertical connections first then perform the horizontal
connections.
.When the vertical connection (A) is selected, be sure to
secure all of the side panels with screws. Never place the
connected extension adaptors on it a table top. (The
fixing method is same as that of the main panel.)
Fig. 1
MKS-8075A
Module covers
Operation module
Screws
(with drop-safe)
Screws
(with drop-safe)

1-14 CCP-9000A
When the Vertical connection is selected
(1) Connect the adaptor cases together.
(Be careful of the direction of the adaptor cases. See the
instruction given on the bottom of the adaptor case.)
(2) Fix the right sides and left sides of the adaptor cases as
shown in the illustration using the two pieces of the con-
necting plate A.
.When fixing the adaptor cases, you can select either
the flat connection or the connection like a flight of
steps.
.When selecting the connection like steps of the
connection method (A), (see Fig. 2 (on page 1-16).)
the two screws are secured with one notch offset
each other.
.When the flat connection method (B, C) is selected,
(see Fig. 2 (on page 1-16).) the two screws are
secured in the same height.
BV3 x10
BV3 x10
Adaptor case
Side plates
Module covers
Operation module
Cap (L)
Cap (R)
Scrwes
(with drop-safe)
Scrwes
(with drop-safe)
BV3 x10
BV3 x10
Connecting procedure
1. Remove the module covers. Remove the screws (BV3
x10) fixing the caps (L) and (R), and remove the caps
in the direction of the arrow.
2. Loosen the four screws (with drop-safe) fixing the
operation module.
3. Hold the two screws (with drop-safe) in the front of
the both sides of the operation module, and remove the
operation module.
4. Remove the screws (BV3 x10) fixing the side plates
to the adaptor case, and remove the side plates.
FRONT
FRONT
BV 3 x10
BV 3 x 10
Connecting
plate A
Connecting
plate A
Instruction given on
the bottom of the case
Adaptor cases