Sony BVE-700 User manual

EDITING CONTROL UNIT
BVE-700
INSTALLATION MANUAL
1st Edition
Serial No. 10001 and Higher

BVE-700
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
Attention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please make
sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.

1 (E)
BVE-700
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 2 (E)
Related manuals................................................................................................... 2 (E)
Trademarks .......................................................................................................... 2 (E)
Installation
1-1. Operating Environment .........................................................................1-1 (E)
1-2. Power Supply ........................................................................................1-1 (E)
1-3. Installation Space ..................................................................................1-2 (E)
1-4. Matching Connectors and Cables..........................................................1-4 (E)
1-5. Input/Output Signals of Connectors......................................................1-5 (E)
1-6. Switch Settings on Boards and LED Description .................................1-8 (E)
1-7. Rack Mounting....................................................................................1-11 (E)
1-8. Installing the BKE-701 .......................................................................1-12 (E)

2 (E) BVE-700
Purpose of this manual This manual is the installation manual of Editing Control Unit BVE-700.
This manual is intended for use by trained system and service engineers, and
describes the information on installing the BVE-700.
Related manuals Beside this Installation Manual, the following manuals are available for the unit.
..
..
.User’s Guide (Supplied with BVE-700)
This manual describes the application and operation of the unit.
..
..
.Operation Manual (Supplied with BVE-700)
This manual describes the overview, system connection examples, and specifica-
tions of the unit.
..
..
.BKE-701 Installation Manual (Supplied with BKE-701)
This manual describes the information related to the installation of the unit.
..
..
.BVE-700/BKE-701 Maintenance Manual (Available on request)
This manual describes the information that premise the service of BVE-700/BKE-
701 based on components replaced.
Trademarks Trademarks and registered trademarks used in this manual are follows.
. Windows is a registered trademark of Microsoft Corporation.
.IBM is a registered trademark of International Business Machine, Inc.
.Ethernet is a registered trademark of Xerox Corporation.
Manual Structure

1-1 (E)
BVE-700
1-1. Operating Environment
Operating guaranteed temperature : +5 dC to +35 dC
Performnace guaranteed temperature : +10 dC to +30 dC
Operating humidity : 10 % to 90 %
(relative humidity)
Storage temperature : _20 dC to +60 dC
Mass : 10 kg
Prohibited locations
.Areas where the unit will be exposed to direct sunlight or
any other strong lights.
.Dusty areas
.Areas where it is subject to vibration.
.Areas with strong electric or magnetic fields.
.Areas near heat sources.
.Areas where is subjected to electricity noise.
.Areas where is subjected to static electricity noise.
Ventilation
The inside of the BVE-700 is cooled by a fan (rear and
sides).
The power supply can be damaged if the exhaust vent (rear
panel) and air intake (front panel) are blocked or the fan is
stopped.
Therefore, leave a blank space of more than 10 cm in the
front and back of the BVE-700.
1-2. Power Supply
1. Power specifications
A switching regulator is used for the power supply of this
unit. The voltage within the range of 100 V to 240 V can
be used without changing the supply voltage.
Power requirements : AC 100 to 240 V ±10 %
50/60 Hz
Current consumption : Maximum 2.5 A
(with all optional boards installed)
n
As the inrush current at turn-on is the maximum 25 A (at
100 V/50 A (at 200 V), the capacity of the AC power must
be commensurate in it.
If the capacity of the AC power is not the adequately large,
the breaker of the AC power at the supply side will operate
or the unit will abnormally operate.
Installation
2. Recommended Power Cord
w
.The power cord is not supplied with the BVE-700. Be
sure to use the power cord that is applicable to places in
the area.
To avoid a fire or an electric shock, be sure to use the
designated power cord.
.Do not damage the power cord.
Otherwise, a fire or electric shock may result.
Required Parts for the U.S.A. and Canada
1Power cord : !1-551-812-11
Required Parts for Europe
1Power cord : !1-782-929-21
1
AC inlet
1
AC inlet

1-2 (E) BVE-700
1-3. Installation Space
Processor unit
26.5
520
440
465
57.2
375
482
61 380
17.5
132.4
Unit : mm
1-3. Installation Space

1-3 (E)
BVE-700
Control panel unit
Unit : mm
340
315.5
281
277.2
315
16.9
15
1-3. Installation Space

1-4 (E) BVE-700
1-4. Matching Connectors and Cables
Use the following connectors, cables, or equivalents when connecting cables to the unit.
Panel indication Connector name Matching connector and cable
Name Sony part No.
Processor unit
PLAYER-1 D-sub 9-pin, Female D-sub 9-pin, Male
PLAYER-2 Connector 9-pin, Male 1-560-651-00*1
PLAYER-3 Junction Shell 9-pin 1-561-749-00
RECORDER
MIXER
SWER
Processor unit
EDL D-sub 9-pin, Male D-sub 9-pin, Female
Connector 9-pin, Female 1-563-815-21
Junction Shell 9-pin 1-561-749-00
Processor unit
GPI D-sub 15-pin, Female D-sub 15-pin, Male
Connector 15-pin, Male 1-564-600-11*1
Junction Shell 15-pin 1-563-376-11
Processor unit
SDI INPUT BNC, 75 ZBNC, 75 Z
SDI OUTPUT 5C-FB coaxial cable*3
Processor unit
REF VIDEO BNC, 75 ZBNC, 75 Z
5C-2V coaxial cable*4
Processor unit/Control panel unit
PANEL D-sub 25-pin, Female D-sub 25-pin, Male
Connector 25-pin, Male 1-560-904-11*1
Junction Shell 25-pin 1-563-377-11
Processor unit
NETWORK RJ-45 modular jack*2__
*1 : To use plugs, the following crimp contacts are required.
AWG #18 to #22 : 1-566-493-21
AWG #22 to #24 : 1-564-774-11
AWG #24 to #30 : 1-564-775-11
*2 : Conforms to the IEEE 802.3 Ethernet 10BASE-T/100BASE-TX standards.
*3 : It is recommend to use the 5C-FB coaxial cable of Fujikura America Inc. or Fujikura Europe Ltd.
*4 : It is recommend to use the 5C-2V coaxial cable of Fujikura America Inc. or Fujikura Europe Ltd.
1-4. Matching Connectors and Cables

1-5 (E)
BVE-700
1-5. Input/Output Signals of Connectors
The input/output signals of the connectors at the rear panel
are as follows.
.Processor unit
PLAYER-1
PLAYER-2
PLAYER-3
RECORDER
MIXER
SWER : RS-422A (D-sub 9-pin, Female)
Pin No. Signal Function
1 GND Ground
2RX_Received data (_)
3TX+Transmitted data (+)
4 GND Ground
5_No Connection
6 GND Ground
7 RX+ Received data (+)
8TX_Transmitted data (_)
9_No Connection
EDL : RS-232C (D-sub 9-pin, Male)
Pin No. Signal Function
1_No Connection
2 RXD Received data
3 TXD Transmitted data
4_No Connection
5 GND Ground
6_No Connection
7 RTS (Not used at present)
8 CTS (Not used at present)
9_No Connection
_ EXT VIEW _
1
5
69
_ EXT VIEW _
5
1
96
GPI : D-sub 15-pin, Female
Pin No. Signal Function
1 GND Ground
2 OUT-1A Relay output-1A
3 OUT-2A Relay output-2A
4 OUT-3 (TTL) Open collector output-3
5 OUT-4 (TTL) Open collector output-4
6 IN-1 (TTL) Input-1
7 IN-3 (TTL) Input-3
8 GND Ground
9 OUT-1B Relay output-1B
10 OUT-2B Relay output-2B
11 _No Connection
12 _No Connection
13 GND Ground
14 IN-2 (TTL) Input-2
15 IN-4 (TTL) Input-4
EXT VIEW
1
8
9
15
1-5. Input/Output Signals of Connectors

1-6 (E) BVE-700
PANEL : D-sub 25-pin, Female
Pin No. Signal Function
1 GND Ground
2 12 V Panel Power Supply
3RX+Received data (+)
4 GND Ground
5TX_Transmitted data (_)
6 12 V Panel Power Supply
7 12 V Panel Power Supply
8_No Connection
9 GND Ground
10 GND Ground
11 GND Ground
12 GND Ground
13 GND Ground
14 12 V Panel Power Supply
15 12 V Panel Power Supply
16 RX_Received data (_)
17 GND Ground
18 TX+Transmitted data (+)
19 12 V Panel Power Supply
20 GND Ground
21 _No Connection
22 GND Ground
23 12 V Panel Power Supply
24 12 V Panel Power Supply
25 GND Ground
NETWORK : 10BASE-T/100BASE-TX (8-pin, Modular jack)
Pin No. Signal Function
1TX+Transmitted data (+)
2TX_Transmitted data (_)
3RX+Received data (+)
4_No Connection
5_No Connection
6RX_Received data (_)
7_No Connection
8_No Connection
1
13
14
25
EXT VIEW
18
_ EXT VIEW _
1-5. Input/Output Signals of Connectors

1-7 (E)
BVE-700
.Control panel unit
PANEL : D-sub 25-pin, Female
Pin No. Signal Function
1 GND Ground
2 12 V Panel Power Supply
3TX+Transmitted data (+)
4 GND Ground
5RX_Received data (_)
6 12 V Panel Power Supply
7 12 V Panel Power Supply
8_No Connection
9 GND Ground
10 GND Ground
11 GND Ground
12 GND Ground
13 GND Ground
14 12 V Panel Power Supply
15 12 V Panel Power Supply
16 TX_Transmitted data (_)
17 GND Ground
18 RX+Received data (+)
19 12 V Panel Power Supply
20 GND Ground
21 _No Connection
22 GND Ground
23 12 V Panel Power Supply
24 12 V Panel Power Supply
25 GND Ground
1
13
14
25
EXT VIEW
1-5. Input/Output Signals of Connectors

1-8 (E) BVE-700
1-6. Switch Settings on Boards and LED Description
1. CKG-27 board
Switch
n
Do not change the setting of the “Factory use” switches.
Ref. No. Address Name Function Factory setting
S651 (B-11) _Factory use
LEDs
Ref. No. Address Color Name Function Normal state
D101 (A-1) Orange +5 V AOK Lights up when +5 V power for analog is supplied. Lights up
D102 (A-1) Orange _5 V AOK Lights up when _5 V power for analog is supplied. Lights up
D104 (A-2) Green REF OK Lights up during reference signal input. Lights up
D105 (A-2) Green PLL OK Lights up when the internal PLL circuit is locked to Lights up
reference signal input (during HD only).
Lights up dim when PLL is not locked
(during HD only).
Side A (component side)
D105 D104 D102 D101
S651
A
B
C
D
E
F
G
H
1234567891011
Factory setting
( indicates the knob position.)
ON
12345678
1-6. Switch Settings on Boards and LED Description

1-9 (E)
BVE-700
2. CPU-317A board
Switches
nn
nn
n
Do not change the setting of the “Factory use”switches.
Ref. No. Address Name Function Factory setting
S1 (D-5) Mode select Sets the operation mode (1).
switch (1) S1-1 : Sets the operation mode.
OPEN : Normal
CLOSE : Forced download mode in order
to write programs in flash memory
(IC26, C27) attached directly to the
CPU board.
S1-2 : Sets the operation mode.
OPEN : Normal
CLOSE : Hardware test mode
S1-3 : Factory use
S1-4 : Factory use
S1-5 : Factory use
S1-6 : Factory use
S1-7 : Factory use
S1-8 : Factory use
S2 (E-5) Mode select Sets the operation mode (2).
switch (2) S2-1 to S2-5 : Sets the reference signal that is input
to REF IN.
Reference S2
Signal -1 -2 -3 -4 -5
1125/59.94 OFF OFF OFF OFF OFF
525/59.94 OFF OFF OFF ON OFF
1125/50 OFF ON ON OFF OFF
625/50 OFF ON ON ON OFF
1125/24 PsF ON OFF ON OFF ON
1125/23.98 PsF ON OFF OFF OFF ON
OFF : OPEN
ON : CLOSE (Push the switch to
the UP position)
Any switch setup other than the
those shown on the above table
is invalid.
S2-6 : Factory use
S2-7 : Setup status
OPEN : Normal operation
CLOSE : The machine starts up with the setup
of USER SETUP DATA1 state.
OPEN
12345678
Factory setting
( indicates the knob position.)
D15 D16 D18 D27
S1 S2 S5
D101
D1 D2 D3 D4 D5 D6 D7 D8
D11 D19 D20 D21 D22
D10
D13
ABCDEFGHJK L
1
2
3
4
5
S3 S4 D14D12
D9
D100
Side A (component side)
OPEN
12345678
Factory setting
( indicates the knob position.)
1-6. Switch Settings on Boards and LED Description

1-10 (E) BVE-700
Ref. No. Address Name Function Factory setting
S2 (E-5) Mode select S2-8 : Initializes setup data of backup
switch (2) memory to the state of factory setting.
OPEN : Normal
CLOSE : Initializing
S3 (K-5) ABORT switch Factory use _
S4 (K-5) Reset switch Resets the BVE-700 and initializes it. _
S5 (E-5) Rotary switch Factory use
LEDs
Ref. No. Address Color Name Function Normal state
D1 (H-5) __Factory use Lights off
D2 (H-5) __Factory use Lights off
D3 (H-5) __Factory use Lights off
D4 (H-5) __Factory use Lights off
D5 (H-5) __Factory use Lights off
D6 (J-5) __Factory use Lights off
D7 (J-5) __Factory use Lights off
D8 (J-5) __Factory use Lights off
D9 (H-4) Green 10B Lights up during 10Base-T Lights up
connection. (when network is not connected)
D10 (H-4) Green ACT Lights up when network is Lights off
communicated. (when network is not connected)
D11 (H-4) Green 100B Lights up during 100Base-TX Lights off
connection. (when network is not connected)
D12 (L-4) Green RUN Factory use Undefined
D13 (L-4) Red FAIL Factory use Lights off
D14 (K-4) Orange VD Lights up when VIDEO reference Lights up (Flickers a bit.)
signal is supplied to the CPU board.
(Flickers a bit.)
D15 (A-5) Orange +5V Lights up when +5 V power for Lights up
digital is supplied.
D16 (A-5) Orange +3V Lights up when +3 V power for Lights up
digital is supplied.
D18 (B-5) Green _5V Lights up when _5 V power for Lights up
analog is supplied.
D19 (H-4) Green RX Lights up during network reception. Lights off
(when network is not connected)
D20 (H-4) Green TX Lights up during network Lights off
transmission. (when network is not connected)
D21 (H-4) Green LINK Lights up when network link is Lights off
established. (when network is not connected)
D22 (H-4) Green COLL Lights up when network collision Lights off
occurs. (when network is not connected)
D27 (B-5) Orange +12 V Lights up when +12 V power is Lights up
supplied.
0
2
3
5
6
7
1
8
Factory setting
4
9
A
B
C
0
F
E
D
1-6. Switch Settings on Boards and LED Description
OPEN
12345678
Factory setting
( indicates the knob position.)

1-11 (E)
BVE-700
1-7. Rack Mounting
The BVE-700 is mounted in the 19-inch standard rack.
To mount the BVE-700 in the rack, use the specified rack
mount kit and follow the procedure described below.
Specified rack mount kit : RMM-10
n
If a rack mount kit other than the specified one is used, the
unit may not be mounted in the 19-inch standard rack.
Parts of the RMM-10
.Rack tools 2 pcs
.Right rack mount adapter 1 pc
.Left rack mount adapter 1 pc
.Rack tool attaching screws 6 pcs
(B4 x6 : 7-682-560-09)
.Rack tool attaching screws 6 pcs
(B4 x10 : 7-682-560-10)
1. Precautions for rack mounting
w
.To prevent the rack from falling or moving, fix the rack
on a flat and steady floor using bolt or others.
If the rack falls due to the weight of the equipment, it
may cause death or injury.
.Be sure to use the specified rack mount kit.
If not, injury may result and the equipment may fall due
to insufficient strength.
.After rack mounting, be sure to tighten the screws on the
rack angle and fix the unit in the rack.
If the screws on the rack angle are not tightened, the unit
may slip from the rack and fall, causing injury.
c
When mounting the unit in the rack, note the following:
.Be sure to mount in the rack with two persons or more.
.Be careful not to catch your fingers or hands in the rack
mount rail or others.
.Mount in the rack in a stable position.
n
If several units are mounted in a rack, it is recommended to
install a ventilation fan to prevent temperature rise inside
the rack.
2. Rack mounting procedure
This section describes the rack mounting procedure using
the RMM-10 rack mount kit.
n
Tighten the screws to the following torque.
Tightening torque : 120 x10_2N.m {12.2 kgf.cm}
1. Attach the rack tool to the side of the equipment using
the specified six screws.
n
Use B4 x6 screws.
2. Loosen the screws on the rear of the right and left
adapters and adjust the length of the adapter according
to the depth of the rack.
(The illustration below shows the left adapter.)
n
Maximum depth of adapter :750 mm
Minimum depth of adapter : 595 mm
B4 x6
B4 x6
1-7. Rack Mounting
B4 x6
Portion of
the rail
Adapter

1-12 (E) BVE-700
B4 x10
(with drop-safe)
B4 x10
(with drop-safe)
B4 x10
(with drop-safe)
Front panel
3. Attach the right and left adapters to the rack complete-
ly using the specified six screws.
(The illustration below shows the left adapter.)
4. Tighten the screws (B4 x6 : two screws each on the
right and left) for adjusting the length of the adapter
completely (the screws that were loosened in step 2).
5. Align the groove of the rack tool at the side of the
equipment with the rail, and slide the equipment to the
rear.
n
The rack tools are hooked on the rails as shown below.
6. Turn off the main power of this unit and disconnect the
plug from the outlet.
7. Fully loosen the four screws (with drop-safe) and
remove the front panel.
8. Fix the rack angle in the rack using the specified
screws.
9. Attach the front panel to the equipment.
1-8. Installing the BKE-701
For the installation procedure, refer to “4. Installation”of
the Installation Manual supplied with the BKE-701.
B4 x10
3U
B4 x10
31.75
31.75
Unit : mm
Rack tool Rack tool
Rail Rail
B5 x12
B5 x12
1-7. Rack Mounting
1-8. Installing the BKE-701

BVE-700
The material contained in this manual consists of
information that is the property of Sony Corporation.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens de
l’équipement à moins d’une permission écrite de Sony
Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind.
Die Sony Corporation untersagt ausdrücklich die
Vervielfältigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben für irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrüstung ohne ausdrückliche
schriftliche Erlaubnis der Sony Corporation.

Printed in Japan
Sony Corporation 2000. 8 16
Communication System Solutions Network Company ©2000
BVE-700 (SY) J, E
3-205-021-01