Steelcase FitWork 7 Series User manual

FitWork™Walkstation
Series 7 AdjusTable
If you have a problem, question, or request, call
your local dealer, or Steelcase Line 1 at
888.STEELCASE (888.783.3522)
for immediate action by people who want to help you.
(Outside the U.S.A., Canada, Mexico, Puerto Rico,
and the U.S. Virgin Islands, call: 1.616.247.2500)
Or visit our website: www.steelcase.com
©2015 Steelcase Inc.
Grand Rapids, MI 49501
U.S.A.
Printed in U.S.A.
®
Page 1 of 20
005720D Rev F
Tools required:
#2 Phillips Bit
with Extension
7/16"
10mm
Socket Wrench
A7TG660606H A7TR663232H
A7TG660632H
A7TR383030H
A7TG663206H A7TR782929H
#2 Square
Drive Bit

Page 2 of 20
005720D Rev F
®
1
2
3
4
STRETCHER ELECTRICAL
PIGTAIL
Unpack and sort all components.
Position top upside down on the assembly surface.
Layout the left and right lift columns, lift the stretcher
into each dovetail, connect loosely. (Left and right is
determined when the table is standing on the base
and is viewed from the front.)
Note: A clean, abrasion free
surface will be necessary for
table assembly.
Worksurface Assembly
NOTCH
RIGHT COLUMN
LEFT COLUMN
STRETCHER
DOVETAIL
DOVETAIL
COLUMN STRETCHER
TOP VIEW
For each lift column, fold the electrical 'pig-tail' towards
the center of the surface. Secure in the notch
provided in each lift column.
5
REAR VIEW
Once each lift column has been engaged, lightly tap each
connection point with a rubber mallet 1/8-1/4 inch at a time, until
completely seated. Do not completely install one lift column at a
time...they must be installed incrementally.
FLUSH

Page 3 of 20
005720D Rev F
®
With the top still upside down on the floor, turn the base over
(flipping is a 2 person job) and align the attachment plates
to the pre-drilled holes in the top. Loosely install one phillips
head fastener in each of the 4 corners of the attachment plate.
Don't install all fasteners until the unit
has been operated through one
cycle (Step 13).
PHILLIPS
HEAD
SCREW
4mm HEX HEAD FASTENERS
ATTACHMENT PLATE
Locate and install each attachment plate using 4mm hex head
fasteners provided. Tighten securely.
67

Page 4 of 20
005720D Rev F
®
Remove four (4) screws on each foot.
Lower treadmill receiver onto legs and attach
using four (4) screws on each leg.
SCREWS
8
9
TREADMILL
RECEIVER

Page 5 of 20
005720D Rev F
®
Install control box in the predetermined
location, using pre-drilled holes.
12
CONTROL BOX
Connect the 120V plug into the control box. Secure the cord to the
control box using the molded-in relief as shown. Do not plug into
the wall outlet/power source yet.
8.
Route lifting column cables through the molded-in channels on
the underside of the control box, and plug into ports 1 and 2.
POWER
CABLE
NOT YET
10
11
11
OR
LIFTING COLUMN 2
CABLE
LIFTING COLUMN 1
CABLE
10
12

Page 6 of 20
005720D Rev F
®
(a)
(e)
(d)
(c)
(b)
Locate pilot holes and place one (1) console mounting bracket assembly
onto underside of worksurface. Attach bracket using three (3) screws (a).
Slide console next to bracket and make sure threaded studs are inserted
into slot (b). Slide other console mounting bracket next to console making
sure holes in bracket are lined up with pilot holes on worksurface (c).
Secure bracket to worksurface using three (3) screws (d).
Secure brackets to each side of console using
two (2) nuts and two (2) flat washers (e).
13
SHOULDER
WASHER
CONSOLE
SHOULDER
WASHER
CONSOLE MOUNTING
BRACKET ASSEMBLY
SCREWS
SCREWS
FLAT WASHERS
AND NUTS
SLOT

Page 7 of 20
005720D Rev F
®
Install the wire management
cableway on the underside of
the worksurface about 5" in
front of the control box.
Connect the cables of each lift column. Route these
cables in the wire management cableway. Refer to
the wiring guide for more information.
15
14
5"
WIRE MANAGER
Note: stretchers and cables not shown for clarity.

Page 8 of 20
005720D Rev F
®
Install the cable located on the back of the console
into the control box as shown. Store extra cable
length into wire manager. Plug the power cord
into an outlet and check for binding. Then,
lower to the bottom and unplug unit.
CONTROLLER CABLE
FROM CONSOLE
16
LIFTING
COLUMN 2
LIFTING
COLUMN 1
POWER
TO PIGTAILS
IN COLUMNS
TO PIGTAILS
IN COLUMNS
CONTROL BOX
CONTROLLER CABLE
FROM CONSOLE
CONTROLLER CABLE
FROM CONSOLE

Page 9 of 20
005720D Rev F
®
Carefully turn the table over (2 person operation).
NOTE: Do NOT use either lift column as a brace
when turning the table over as this may cause
binding. The top must be lifted free, rotated
and set down carefully.
Install treadmill. Align treadmill with unit as
shown. Make sure the two (2) treadmill
feet are inserted into the two (2)
holes in the treadmill receiver.
NOTE: The holes in the treadmill
receiver are for the treadmill feet,
not the treadmill wheels.
HOLE IN TREADMILL
RECEIVER
18
17
TREADMILL
TREADMILL FOOT

Page 10 of 20
005720D Rev F
®
a
b
c
Locate back left of treadmill and plug in signal cable as indicated
(a). Locate back center of console and plug in other end of
signal cable as indicated (b). Plug the cord of the table and the
treadmill into an outlet. Make sure treadmill is turned on (c).
NOTE for (a) & (b): Be sure to secure signal cable to the console
and treadmill with the screws integral to the cable connector.
This will ensure a good connection.
REAR OF
TREADMILL
19
SIGNAL CABLE
CONSOLE
View from Underneath
Worksurface
SIGNAL CABLE
CONSOLE