Steelcase Migration SE Pro User manual

Migration SE Pro
User Guide
用户指南

Ergonomics for sit and stand desk
Sit position
1. Sit fully back into your chair and adjust your seat height so that your thighs
and feet are parallel to the ground.
2. Relax your shoulders and adjust the table height so that your elbows
and forearms can rest comfortably at 90 degree angle on the chair arm or
the worktop.
3. If you use a monitor arm, look straight ahead and adjust the top of the
monitor to your eye level, adjust the monitor so that it is one arm’s length
away from your body.
Stand position
1. Stand up straight with your feet parallel to the floor.
2. Relax your shoulders and adjust the table height so that your forearms can
rest comfortably at 90 degree angle on the worktop.
3. If you use a monitor arm, look straight ahead and adjust the top of the
monitor to your eye level, adjust the monitor so that it is one arm’s length
away from your body.

Pinch Points, Keep Clear
RISKS OF SERIOUS INJURY
If not used as intended, moving worksurfaces can pinch and cause injury or
property damage. Always follow these instructions:
1. Keep height-adjustment range free from obstructions above and below
the worksurface.
2. Plan for a minimum 25mm gap against a wall or panel.
3. Plan for a minimum 25mm gap to adjacent furniture.
WARNING
Max.
Min.
>1"
(25mm)
>1"
(25mm)
>1"
(25mm)
X
NO CHILDREN

Reset Instructions
RESETTING THE BASE
Note:
Make sure there is nothing under the base before setting to its
lowest position. If the cable is obstructed it will not reset
properly.
1. Press and hold the Down arrow; the desk will begin to go down.
2. Once the desk reaches its lowest height, continue to press the Down arrow
for 5 seconds, until the digital display shows “RST”.
3. Release and then press the Down arrow again; the recalibration process will
now begin.
4. When reset is complete, the digital display will show 650mm (3-stage) or
720mm (2-stage).
Standard Handset - Up/Down Controls
A. Up Button
B. Down Button
Upgraded Handset - 4 Memory Preset
A. Height Adjustment Buttons
B. Memory Position Buttons
C. Memory Setting Buttons
D. Digital Display
Height Ranges
2-Stage : 720mm - 1180mm
3-Stage : 650mm - 1250mm
CONTROLLER LAYOUT

Troubleshooting Guide
Most issues will resolve by re-setting the base. See reset instructions on previous
page.
Note:
Make sure there is nothing under the base before setting to its lowest
level. If the cable is obstructed it will not reset properly.
Please ensure that all connections are tight and intact before further troubleshooting.
ISSUE SOLUTION
ASR/RST Error Code Reset the base.
No power/LED on control box The control box may be damaged-contact us for
is off replacement.
E07/E08 Error Code (legs not 1. Reset the base.
moving uniformly) 2. If the issue persists, swap the connecting
cables.
3. If the issue persists, contact us for a
replacement.
H01 Error Code (Controller Disconnect the power for 1 minute and then
Overheat) reconnect the handset.
Handset Display Error (eg: The handset may be damaged-contact us for
“88.8”) replacement.
Base is not moving or 1. Make sure that all connections are intact and
operates irregularly. that the outlet has power.
2. Once connection are verified, reset the base.
3. If the issue persists, please contact our
Customer Care.
Base stops and can only 1. Base might be overloaded.
move downwards. 2. Remove some of the weight on the
worksurfaces and try again.
3. If the issue persists, please contact customer
service.
Movement only in one leg. 1. Make sure that all connections are intact and
the outlet has power.
2. Once connections are verified, reset the base.
3. If the issue persists, please contact customer
service.
For questions and support, please contact Steelcase Customer Care.

以人体工程学的坐姿和站姿使用升降桌
最适合的坐姿
1. 请完全就坐于座椅中，并调整座椅高度，使您的大腿及双脚与地面呈平行。
2. 放松肩部，并调整桌子高度，使您的肘部与前臂呈90度舒适地置于座椅扶手或
桌面上。
3. 如果您使用显示屏支臂，请直视前方，并调整显示屏的顶部与您的视线齐平，
再调节显示屏，使其与您的身体保持一个手臂的长度距离。
最适合的站姿
1. 呈挺直站姿，双脚与地面平行。
2. 放松肩部，并调整桌子高度，使您的前臂呈90度舒适地置于桌面上。
3. 如果您使用显示屏支臂，请直视前方，并调整显示屏的顶部与您的视线齐平，
再调节显示屏，使其与您的身体保持一个手臂的长度距离。

1. 在可升降的范围内，确保桌面的上方和下方不会触碰到任何
阻碍物。
2. 确保与相邻的办公家具之间至少有25mm的空隙。
安全间隙
WARNING
最高
最低
>1"
(25mm)
>1"
(25mm)
>1"
(25mm)
X
严禁儿童单独使用

重置设定
基本控制 - 上/下控制键
A. “向上”按鈕
B. “向下”按鈕
A. 升降調節按鈕
B. 記憶位置按鈕
C. 記憶設置按鈕
D.
數字顯示
高度范围
2-段: 720mm - 1180mm
3-段: 650mm - 1250mm
控制键选项
1. 按住向下的箭头按钮不放；桌子会开始下降。
2. 一旦桌子达到了最低的高度，继续按住向下箭头按钮5秒，直到数字显示面板
显示“RST”
3. 松开然后按住向下箭头按钮，校准过程将会开始。
4. 当重新设置完成后，数字显示将会显示650mm (3-段)或者720mm (2-段)。
注意：在调节至最低的高度之前，确保底座下没有任何其它异物。如果有阻碍物
阻挡了电缆线，则无法进行重新设置。
。
升级控制 - 4档预设参数界面

故障排除
请确保故障排除之前，所有的连接线路完好
问题 解决方案
ASR/RST 错误模式 重新调整基座
无电源控制箱上的LED 不亮 控制箱可能破损联系更换
E07/E08 错误模式（桌腿不是
同步活动）
1. 重新调整基座
2. 如果问题还是存在，掉换连接线缆
3. 如果问题还是存在，联系更换
H01 错误模式（控制器过热） 拔掉电源1分钟，然后重新连接手控
手控显示器出错（如，"88.8"） 手控可能破损联系更换
底座无法活动或者偶尔无法
操作
1. 确保所有的连接线路完好，电源插座通电
2. 一旦排除连接问题，重新调整基座
3. 如果问题还是存在，请联系客户服务
基座停止不动或者只能向下
活动
1. 基座负载量过大
2. 移除工作台上的一些重量，重试
3. 如果问题还是存在，请联系客服
只有一个桌腿可活动 1. 确保所有的连接线路完好，电源插座通电
2. 一旦排除连接问题，重新调整基座
3. 如果问题还是存在，请联系客户服务
如果有任何问题或需要支持，随时联系Steelcase 客服。
大部分的问题可以通过以下重新调整底座来解决，如果问题还是存在，请联系客
户服务。
注意：在调节至最低的高度之前，确保底座下没有任何其它异物。如果有阻碍物
阻挡了电缆线，则无法进行重新设置。