Sunny Health & Fitness SF-E905 User manual

MAGNETIC ELLIPTICAL BIKE
SF-E905
USER MANUAL
IMPORTANT! Please retain owner’s manual for maintenance and adjustment instructions.
Your satisfaction is very important to us,PLEASE DO NOT RETURN UNTIL YOU HAVE
CONTACTED US: [e-mail] or 1- 877 - 90SUNNY (877-907-8669).

1
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this
equipment correctly. It is important to read this entire manual before assembling and using the
equipment. Safe and effective use can only be achieved if the equipment is assembled,
maintained and used properly. It is your responsibility to ensure that all users of the equipment
are informed of all warnings and precautions.
1. Before starting any exercise program, you should consult your physician to determine if
you have any medical or physical conditions that could put your health and safety at risk, or
prevent you from using the equipment properly. Your physician’s advice is essential if you
are taking medication that affects your heart rate, blood pressure or cholesterol level.
2. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health.
Stop exercising if you experience any of the following symptoms: pain, tightness in your
chest, irregular heartbeat, shortness of breath, lightheadedness, dizziness or feelings of
nausea. If you do experience any of these conditions, you should consult your physician
before continuing with your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use
only.
4. Use the equipment on a solid, flat level surface with a protective cover for your floor or
carpet. To ensure safety, the equipment should have at least 4 feet (1.2 M) of free space
all around it.
5. Ensure that all nuts and bolts are securely tightened before using the equipment. The
safety of the equipment can only be maintained if it is regularly examined for damage
and/or wear and tear.
6. Always use the equipment as indicated. If you find any defective components while
assembling or checking the equipment, or if you hear any unusual noises coming from the
equipment during exercise, discontinue use of the equipment immediately and do not use
until the problem has been rectified.
7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may
become entangled in the equipment.
8. Do not place fingers or objects into the moving parts of the equipment.
9. The maximum weight capacity of this unit is 220 pounds (100 KG).
10.The equipment is not suitable for therapeutic use.
11.To avoid bodily injury and/or damage to the product or property, proper lifting and moving
is required.
12.Your product is intended for use in cool, dry conditions. You should avoid storage in
extreme cold, hot or damp areas as this may lead to corrosion and other related problems.
13.This equipment is designed for indoor and home use only, it is not intended for commercial
use!

2
EXPLODED DIAGRAM 1

3
EXPLODED DIAGRAM 2
HARDWARE PACKAGE
#102 S8 1PC
#103 S6 1PC
#19LΦ16*89*L23*B0.5*20-L 1PC
#19RΦ16*89*L23*B0.5*20-R 1PC
#37 M8*40 4PCS
#28 M10*L45*L25 4PCS
#104 S13
、
S14 2PCS
#105 S17
、
S19 2PCS
#29 d10*1.5 4PCS
#30 M10 4PCS
#14 Φ20*d8.5*R25 4PCS
#33 M8 4PCS
#39 Φ
13XB2
2PCS
#40L
B0.5X20
1 PC
#40R
B0.5X20
1 PC

4
PARTS LIST
No.
Description
Spec.
Qty.
No.
Description
Spec.
Qty.
1 Main Frame
1
39 Spring Washer Φ13XB2 2
2 Front Stabilizer 1
40L/R Nylon Nut B0.5X20 1pr.
3 Rear Stabilizer 1
41 Nut Cap S17 4
4 Roller Cap 2
42 Square End Cap 2
5 Leveler Cap 2
43 Foam Grip 2
6 Carriage Bolt M10XL57 4
44 Foam Grip 2
7 Arc Washer
Φ
10X1.5X
Φ
25XR28
4
45 Round End Cap 2
8 Domed Nut M10 4
46 Pulse Sensor Wire 2
9 Handlebar Post 1
47 Spherical Cap 2
10a Tension Controller 1
48 Mushroom Cap 2
10b Tension Cable 1
49 Crank Arm 1
11 Phillips Screw 1
50
Tension Controller
Cover
1
12 Flat Washer 1
51 Hex Bolt M10X50 2
13 Allen Bolt M8X20 4
52 Connecting Joint 2
14 Arc Washer Φ20Xd8.5XR25 8
53 Axle Bushing 1 4
15 Upper Senor Wire 1
54 Flat Washer d10X1.5 2
16 Lower Sensor Wire 1
55 Alloy Bushing 4
17 Tension Hook 1
56 Nylon Nut M10 2
18L/R Pedal Support Tube 1pr.
57 Nut Cap S19 2
19L/R Hinge Bolt Φ16X89 1pr.
58 Nut Cap S14 4
20 Nut Cap S13 2
59 Spacer Φ32X59 2
21 Hex Bolt M8X55 2
60 Axle Bushing 2 4
22 Flat Washer d8X15 2
61 Wave Washer Φ17.1XΦ23 X 0.3 2
23 Nylon Nut M8（Black color）
2
62 Nylon Nut 1
24L/R Swing Bar (L/R) 1pr.
63 Plug 2
25 Hex Bolt M8X15 2
64 Crank Cover 2
26 Flat Washer Φ8.2XΦ32X2 2
65L/R Chain Cover 1pr.
27L/R Pedal 1pr.
66 Nut 1
28 Hex Bolt M10XL45 4
67 Washer 1
29 Flat Washer d10X1.5 4
68 Two-slot Nut 1
30 Nylon Nut M10 (White color) 4
69 Ball Bearings 2
31 Armrest 1
70 Bearing Housing 2
32L/R Handlebar 1pr.
71 Sensor 1
33 Domed Nut M8 4
72 Bolt ST3X10 2
34 Spring Washer d8X1.5 2
73 Three-slot Nut 1
35 Hex Bolt 2
74 Big Washer 1
36 Decorative Cover 1
75 Belt 1
37 Carriage Bolt M8X40 4
76 Belt Pulley 1
38 Meter 1
77 Hex Bolt M5XL60 1

5
78 Hex Nut M5 2
92 Bearing 6000z 2
79 Hex Bolt M6XL15 2
93 Flywheel Axle 1
80 Spring Washer d6 2
94 Flywheel 1
81 Flat Washer D6 2
95 Bolt ST4.3X20 5
82 Axle Stop Ring
2
96 Flange Nut 1
83 Magnetic Board Axle
1
97 Bolt ST5X20 4
84 Magnetic Board
1
98 Flat Washer d10X20X1.5 1
85 Spring
1
99 Flat Washer d5X1 4
86 Square Magnet
8
100 Flat Washer d8X19X1.5 2
87 Hex Thin Nut
M10X1
1
101 Alloy Sleeve
1
88 Adjusting Chain Bolt
M6X50
2
102 Wrench
S=8
1
89 Adjusting U Washer
2
103 Wrench
S=6
1
90 Hex Nut
M6
2
104 Spanner
S=13
、
14
2
91 Spacer 1
105 Spanner
S=17
、
19
2
Ordering Replacement Parts (U.S. and Canadian Customers only)
Please provide the following information in order for us to accurately identify the part(s) needed:
The model number (found on cover of manual)
The product name (found on cover of manual)
The part number found on the “EXPLODED DIAGRAM” and “PARTS LIST” (found near the front
of the manual)
Please contact us at [e-mail] or 1- 877 - 90SUNNY (877-907-8669).

6
ASSEMBLY INSTRUCTION
STEP 1:
Attach the Front Stabilizer (No. 2) and
Rear Stabilizer (No. 3) onto the Main
Frame (No. 1), secure with 4 Carriage
Bolts (No. 6), 4 Arc Washers (No. 7)
and 4 Domed Nuts (No. 8) which are
pre-attached to the stabilizer, tighten
with the Spanner (No. 105).
★Ensure that all bolts and washers are
in place and partially threaded in before
completely tightening any of them.
STEP 2:
A: Connect the Lower Sensor Wire
(No. 16) to the Upper Senor Wire (No.
15), and then connect Tension Hook
(No. 17) with Tension Cable (No. 10b)
as shown in Picture A.
Note: Make sure the Tension
Controller (No. 10a) is at the lowest
level before you connect the Tension
Control Cable. This ensures the wires
are at their longest point. We
recommend the assistance of a second
person to help hold the Handlebar Post
(No. 9). This will make the connection
easier when you are attaching Tension
Hook (No. 17) to Tension Cable (No.
10b).
B: Remove the preassembled 4 Allen
Bolts (No. 13) and 4 Arc Washers (No.
14) from the Main Section. Insert the
Handlebar Post (No. 9) into the post of
the Main Frame (No. 1); secure in place
with 4 Allen Bolts (No. 13) and 4 Arc
Washers (No. 14) with the Wrench (No.
103).
★Ensure that all bolts and washers
are in place and partially threaded in
before completely tightening any of
them.

7
STEP 3:
A: Attach the Swing Bar (No. 24L/R)
to the long axle of the Handlebar Post
(No. 9) with Hex Bolt (No. 25)and
Flat Washer (No. 26) with 2
Spanners (No. 104).
Note: Please do not fully tighten at this
time.
B: Attach the 2 Pedal Support
Tubes (No. 18L/R) to the Crank Arm
(No. 49) with 2 Hinge Bolts (No.
19L/R), 2 Wave Washers (No. 61),
then put on 2 Spring Washers (No.
39) and 2 Nylon Nuts (No. 40L/R) to
the end of 2 Hinge Bolts (No. 19L/R)
using Wrench (No. 102) and Spanner
(No. 105). (Note: The end of LEFT
Nylon Nut (No. 40L) is Blue, while the
RIGHT Nylon Nut (No. 40R) is White.
Note: Please do not fully tighten at this
time.
C: Fasten the 2 Swing Bars (No.
24L/R) and the 2 Pedal Support
Tubes (No. 18L/R) tightly with 2 Hex
Bolts (No. 21), 2 Flat Washers (No.
22) and 2 Nylon Nuts (No. 23) using 2
Spanners (No. 104).
D: Fasten 2 Hex Bolts (No. 25) and 2
Nylon Nuts (No. 40L/R) tightly now.
Then cover with the 8 Nut Caps (No.
20) (No. 58) (No. 57).
★Ensure that all bolts and washers
are in place and partially threaded in
before completely tightening any of
them.
IMPORTANT: Hinge Bolt (No. 19L/R) is labeled L for LEFT and R for RIGHT.
Please make sure to turn Left Hinge Bolt (No. 19L) counter clockwise and
Right Hinge Bolt (No. 19R) clockwise.
The Hinge Bolt (No. 19L/R) must fully penetrate the nylon ring of the Nylon Nut
(No. 40L/R). This will ensure the stability and durability of your Elliptical Trainer.
In order to install the hinge bolt properly, it must go through the Connecting
Joint (No. 52L/R) and then screw into the hole of the Crank Arm (No. 49L/R).
Then attach Spring Washer (No. 39) and Nylon Nut (No. 40L/R) to the end of
Hinge Bolt (No. 19L/R). If the hinge bolt is connected to the crank arm at an
angle, damage to both the hinge thread and the crank arm may occur.

8
If you experience any trouble with this step; please STOP and read our alternate assembly directions
below before continuing. Incorrect installation can result in permanent damage to your machine.
If you have trouble connecting this part; try this alternate assembly suggestion:
Step A
Disconnect the Connecting Joint (No.
52L/R) from the Pedal Support Tube (No.
18L/R).
Step B
Insert the Locking Bolt (No. 19L/R)
through the hole of the Connecting Joint
(No. 52L/R), then screw the Locking Bolt
(No. 19L/R) in the Crank Arm (No. 49).
*Remember when assembling the left side,
you must screw counter-clockwise to
tighten. Connect the Spring Washer (No.
39) and Nylon Nut (No. 40L/R) and attach
the End Cap (No. 41). You can now
reattach the Connecting Joint (No. 52L/R)
to the Support Tube (No.18L/R).
STEP 4:
Secure the 2 Pedals (No. 27L/R) to the 2
Pedal Support Tubes (No. 18L/R)
respectively using 4 Hex Bolts (No. 28), 4
Flat Washers (No. 29) and 4 Nylon Nuts
(No. 30) using Spanner (No. 105).
CAUTION:
Both pedals are labeled; L for LEFT and
R for RIGHT.

9
STEP 5:
A: Remove the preassembled 2Spring
Washers (No. 34) and 2 Hex Bolts (No.
35) from the Handlebar Post (No. 9).
Attach Armrest (No. 31) to the
Handlebar Post (No. 9) in place. Secure
it with 2 Spring Washers (No. 34) and 2
Hex Bolts (No. 35) that just removed
using Wrench (No. 103), and then pull
the Pulse Sensor Wire (No. 46) out of
the Handlebar Post (No. 9). Finally
attach the Decorative Cover (No. 36)
onto the Armrest (No. 31).
B: Attach the 2 Handlebars (No. 32L/R)
on the 2 Swing Bars (No. 24L/R) with 4
Carriage Bolts (No. 37), 4 Arc Washers
(No. 14) and 4 Domed Nuts (No. 33)
using Spanner (No. 104).
Note:If the Handlebar (No. 32L/R) rubs
against the Armrest (No. 31) during the
workout please confirm you assembled
the correct parts to the correct side. You
should attach Handlebar (No. 32L) to
Swing Bar (No. 24L)according to the
label marked with L or R. while
assembling the left side.
STEP 6:
Connect the 2 Pulse Sensor Wires
(No. 46) and Upper Sensor Wire
(No. 15) to the Meter (No. 38)
respectively. Align the slot of the
Handlebar Post (No. 9) to the bulge
inside the Meter (No. 38) then slide it
onto the Handlebar Post (No. 9)
slowly.
Note: To avoid damaging the wires
please push them into the Handlebar
Post (No. 9) before sliding the Meter
(No. 38)onto it.
ASSEMBLY IS COMPLETE!