Target wiley TGZLMEDXWH User manual

wiley
media cabinet
>> assembly instructions
style # TGZLMEDXWH (true white)
dpci # 249-10-1972
tcin # 53546407
style # TGZLMEDXBL (orion blue)
dpci # 249-10-1973
tcin # 53546411
style # TGZLMEDXGY (gray)
dpci # 249-10-1974
tcin # 53546412
© 2018 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re condent you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a working surface to prevent product damage during assembly.
3. Read through and review assembly steps.
4. Gather all tools prior to assembly.
tools needed

3
table of contents
introduction 2
hardware 4-5
parts list 6
how to use the cam lock system 7
assembly 8-20
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.

4
hardware
(H1) x 31
dowel
(H2) x 24
cam bolt
(H3) x 24
cam
(H4) x 23
short pan head screw
(H5) x 2
knob
(H6) x 2
knob bolt
(H7) x 32
short at head screw
(H8) x 16
bolt
(H9) x 16
lock washer
(H10) x 18
washer
(H11) x 1
allen wrench
(H12) x 4
mounting plate
(H13) x 8
conrmat screw
(H14) x 1
wall anchor
(H15) x 1
wall screw

5
hardware
(H16) x 1
wall strap
(H17) x 1
long pan head screw
(H18) x 8
long at head screw
(H19) x 8
corner block

exploded diagram
ITEM DESCRIPTION QUANTITY
1 top panel 1
2 left side panel 1
3 right side panel 1
4 bottom panel 1
5 back panel 1
6 upper rail 1
7 upper partition 1
8xed shelf 1
9 lower partition 1
10 drawer front 2
11 left drawer side 2
12 right drawer side 2
13 drawer back 2
14 drawer bottom 2
15 foot 4
16 center foot 1
6
QUANTITY

how to use the cam lock system
1.
Screw cam bolt into panel
2.
Align cam bolt(s) with cross-bored
hole(s) and insert all the way until
panels are ush
3.
Push cam into panel - arrow feature
on cam top points to panel edge
4.
Rotate cam(s) clockwise 180° to
lock panels together
5.
Panels should be tight against each
other and connection should be rigid
7
1. 2. 3.
4. 5.

step 1: attach upper rail to top panel
(H1) x 3
wooden dowel
(H2) x 2
cam bolt
(H3) x 2
cam
1.1. Carefully tap small wooden dowels into place in upper rail. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush in upper rail.
1.3. Refer to page 7 for instructions on how to use the cam lock system.
1.4. Do not over tighten bolts.
8

step 2: attach top panel and xed shelf to upper partition
(H1) x 4
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
2.1. Carefully tap small wooden dowels into place in top panel and xed shelf. Leave 1/2” of the dowels sticking out.
2.2. Screw-In cam bolts must be screwed down ush in top panel and xed shelf.
2.3. Refer to page 7 for instructions on how to use the cam lock system.
2.4. Do not over tighten bolts.
9
nished edge
1.1. Carefully tap small wooden dowels into place in upper rail. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down ush in upper rail.
1.3. Refer to page 7 for instructions on how to use the cam lock system.
1.4. Do not over tighten bolts.

step 3: attach lower partition and bottom panel
(H1) x 4
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
3.1. Carefully tap small wooden dowels into place in xed shelf and bottom panel. Leave 1/2” of the dowels sticking out.
3.2. Screw-In cam bolts must be screwed down ush in xed shelf and bottom panel.
3.3. Refer to page 7 for instructions on how to use the cam lock system.
3.4. Do not over tighten bolts.
10
nished edge

step 4: attach left side panel
(H1) x 6
wooden dowel
(H2) x 7
cam bolt
(H3) x 6
cam
4.1. Carefully tap small wooden dowels into place in left side panel. Leave 1/2” of the dowels sticking out.
4.2. Screw-In cam bolts must be screwed down ush in left side panel.
4.3. Refer to page 7 for instructions on how to use the cam lock system.
4.4. Do not over tighten bolts.
11
(H1) x 6
wooden dowel
(H2) x 7
cam bolt
(H3) x 6
cam

step 5: attach right side panel
(H1) x 6
wooden dowel
(H2) x 7
cam bolt
(H3) x 6
cam
5.1. Carefully tap small wooden dowels into place in right side panel. Leave 1/2” of the dowels sticking out.
5.2. Screw-In cam bolts must be screwed down ush in right side panel.
5.3. Refer to page 7 for instructions on how to use the cam lock system.
5.4. Do not over tighten bolts.
12
(H3) x 6

step 6: attach upper rail
(H3) x 2
cam
6.1. Finish attaching upper rail by installing remaining cams.
6.2. Refer to page 7 for instructions on how to use the cam lock system.
6.3. Do not over tighten bolts
13
Finish attaching upper rail by installing remaining cams.
Refer to page 7 for instructions on how to use the cam lock system.

step 7: attach back panel
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H4) x 23
short pan head
screw
7.1. Make sure the short pan head screws go through the pre-drilled holes properly to attach back panel. Do not over tighten screws.
14
hole for anti-tip

step 8: attach mounting plate to foot
(H12) x 4
mounting plate
(H13) x 8
conrmat screw
8.1. Align conrmat screws with pre-drilled holes to attach mounting plate to foot. Do not over tighten screws.
15

step 9: attach feet
(H8) x 16
bolt
(H9) x 16
lock washer
(H10) x 16
washer
(H11) x 1
allen wrench
9.1. Align bolts with pre-drilled holes to attach feet to bottom panel. Do not over tighten bolts.
9.2. Align center foot with pre-drilled hole to attach to bottom panel.
16
(H11) x 1
allen wrench
Align bolts with pre-drilled holes to attach feet to bottom panel. Do not over tighten bolts.
Align center foot with pre-drilled hole to attach to bottom panel.

step 10: attach drawer sides to drawer front
(H1) x 8
dowel
(H7) x 32
short at head
screw
(H19) x 8
corner block
10.1. Align short at head screws with pre-drilled holes to attach corner blocks to drawer front. Do not over tighten screws.
10.2. Carefully tap small wooden dowels into place in drawer front. Leave 1/2” of the dowels sticking out.
10.3. Align short at head screws with pre-drilled holes to attach drawer sides to drawer front. Do not over tighten screws.
17

step 11: attach drawer bottom and drawer back
(H18) x 8
long at head
screw
11.1 Insert drawer bottom into grooves located on drawer sides and drawer face.
11.2. Align long at head screws with pre-drilled holes to attach drawer back to drawer sides. Do not over tighten screws.
18

step 12: attach knobs and install drawers
(H5) x 2
knob
(H6) x 2
knob bolt
12.1. Align knob bolts with pre-drilled holes to attach knob to drawer front. Do not over tighten bolts.
12.2. Carefully align glides on drawer sides with glides on cabinet to install drawer.
19
(H6) x 2
knob bolt

step 13: install anti-tip kit
(H10) x 2
washer
(H17) x 1
long pan head
screw
(H14) x 1
wall anchor
(H15) x 1
wall screw
(H16) x 1
wall strap
Position against wall
Mark position of strap hole on wall
Drill 1/4” hole
Tap in wall anchor
Fasten anti-tip strap with wall screw
provided
20
(H15)
(H14)
(H10)
(H16)
(H10)
(H17)
Mark position of strap hole on wall
Fasten anti-tip strap with wall screw
provided