Teknik Clifton Place 5421116 User manual

www.teknikoffice.co.uk
Hutch
Clifton Place Collection | Model 5421116
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
For things 'n such.
Teknik

Table of Contents Assembly Tools Required
3
4
5-14
15-17
18-20
21-22
23
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Page 2
Electric drill with 1/4" bit
(ONLY in indicated step)

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BRACE (1)
E MOLDING (2)
F UPPER ADJUSTABLE SHELF (1)
G LOWER ADJUSTABLE SHELF (1)
H BACK (1)
Now you know
our ABCs.
Page 3
A
B
C
D
E
F
G
H
E

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
Page 4
CAM SCREW - 4
2
APPLIQUE CARD - 1
8
WOOD DOWEL - 4
3
RUBBER SLEEVE - 8
6
METAL PIN - 8
5
SHORT WOOD
DOWEL - 4
4
BLACK 1-1/2" FLAT HEAD SCREW - 4
10 BLACK 1-1/8" FLAT HEAD SCREW - 6 11
SILVER 5/8" FLAT HEAD SCREW - 6
13
BLACK 1" PAN HEAD SCREW - 8
12
HIDDEN CAM - 4
1
FURNITURE TIPPING RESTRAINT KIT - 1
99
BACK CONNECTOR - 6
7
BRACKET - 2
9

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Insert four HIDDEN CAMS (1) into the TOP (C).
Page 5
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
(4 used)
1
Arrow
C
Surface with groove

Step 2
å Insert four WOOD DOWELS (3) into the ENDS (A and B).
å Turn four CAM SCREWS (2) into the ENDS (A and B).
å Insert four SHORT WOOD DOWELS (4) into the MOLDINGS (E).
Page 6
A
B
E
E
3
2
4
3

å Fasten the MOLDINGS (E) to the TOP (C). Use six BLACK
1-1/8" FLAT HEAD SCREWS (11).
å NOTE: Be sure the SHORT WOOD DOWELS in the
MOLDINGS insert into the TOP.
Step 3
Page 7
Groove
EE
C
BLACK 1-1/8" FLAT HEAD SCREW
(6 used in this step)
11
Remember:
Righty tighty.
Lefty loosey.

Step 4
å Fasten the TOP (C) to the LEFT END (B). Tighten two
HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWEL in the LEFT END
inserts into the TOP.
å Unfold the BACK (H) and slide the BACK into the grooves
in the TOP (C) and LEFT END (B).
Page 8
C
Groove
C
B
H
B
1
2
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
NOTE: Position the
BACK exactly as shown.
Finished surface
without tape

å Place the BRACE (D) onto the WOOD DOWEL in the LEFT END (B).
å NOTE: Be sure the BACK inserts into the groove in the BRACE.
å Fasten RIGHT END (A) to the TOP (C). Tighten two HIDDEN CAMS.
å NOTE: Be sure the BACK inserts into the groove in the RIGHT END.
å NOTE: Be sure the WOOD DOWELS in the RIGHT END insert into
the TOP and BRACE.
Step 5
Page 9
C
A
Groove
D
B
Groove

Step
å Carefully turn your unit over onto its front edges.
å Fasten the ENDS (A and B) to the BRACE (D). Use two BLACK
1-1/2" FLAT HEAD SCREWS (10).
å Insert six BACK CONNECTORS (7) into the grooves in the
ENDS (A and B). Space the BACK CONNECTORS as shown in
the diagram.
å NOTE: You may need to gently tap them in with your hammer.
å Fasten the BACK (H) to your unit. Use six SILVER 5/8" FLAT
HEAD SCREWS (13) through the BACK CONNECTORS and
into the ENDS.
Step 6
Page 10
BLACK 1-1/2" FLAT HEAD SCREW
(2 used in this step)
10
D
A
B
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
H
7
7
SILVER 5/8" FLAT HEAD SCREW
(6 used in this step)
13