Teknik Lateral Filer 5421114 User manual

www.teknikoffice.co.uk
Congratulations. You
are now an adult.
Lateral Filer
Clifton Place Collection | Model 5421114
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Teknik

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
3
4
5-24
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D TOP MOLDING (1)
E UPPER BACK (1)
F BRACE (1)
G LOWER BACK (1)
H BOTTOM (1)
I BOTTOM MOLDING (2)
J LEFT DRAWER SIDE (2)
K DRAWER BACK (2)
L RIGHT DRAWER SIDE (2)
M DRAWER BOTTOM (2)
N DRAWER BRACE (2)
O DRAWER FRONT (2)
P FOOT (4)
A
B
C
D
E
F
G
H
I
IJ
J
K
K
L
L
M
M
N
N
O
O
P
P
P
P
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
ANGLED HEAD
CAM SCREW - 20
2
Angled head
LARGE HIDDEN
CAM - 20
1
WOOD
DOWEL - 18
6SHORT WOOD
DOWEL - 6
7
LONG WOOD
DOWEL - 4
5
APPLIQUE CARD - 1
19
BLACK 1-1/2" FLAT HEAD SCREW - 14
21
SILVER 5/8" FLAT HEAD SCREW - 8
23 SILVER 1/2" FLAT HEAD SCREW - 8 24 BLACK 1/2" PAN HEAD SCREW - 36 25
SMALL HIDDEN
CAM - 12
3STRAIGHT HEAD
CAM SCREW - 12
4
Straight head
LARGE
APPLIQUE CARD - 1
20
ADJUSTABLE
GLIDE -4
16
GROMMET
WITH CAP- 1
9
PULL - 2
8
BLACK 1-1/8" FLAT HEAD SCREW - 9
22
(EXTENSION SET SHOWN SEPARATED)
QEXTENSION RAIL - 4 REXTENSION SLIDE - 4
WASHER - 4
14
ANTI TIP KIT -2
17 HOOK - 4 18
11 SHORT FILE GLIDE - 4
12 LONG FILE GLIDE - 2 13 NOTCHED FILE GLIDE - 2
10 FILE HANGER - 4
LOCK PACK - 2
15
Page 4

Step 1
Arrow (20 used)
Arrow
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å NOTE: If you are attaching the 421116 Hutch to your unit,
build the Hutch first.
å Push twenty HIDDEN CAMS (1) into the
ENDS (A and B), BRACE (F), LOWER BACK (G),
UPPER BACK (E) and BOTTOM (H).
Arrow
1
1
The arrow in the HIDDEN
CAM must point toward the
hole in the edge of the board.
Hole
A
B
F
E
H
G
Page 5www.sauder.com

å Peel an applique from the LARGE APPLIQUE CARD (20)
and stick one on each large hole in the BOTTOM (H).
å Flip the BOTTOM (H) over.
å Turn and tighten four FEET (P) into the threaded holes in
the BOTTOM (H).
å Turn four ADJUSTABLE GLIDES (16) into the threaded
holes in the FEET (P).
Step 2
H
20
H
P
P
P
P
16
Page 6
F
l
i
p
t
h
e
B
O
T
T
O
M
o
v
e
r
Surface without
HIDDEN CAMS

Step
I
Page 7
å Insert four SHORT WOODEN DOWELS (7) into the
BOTTOM (H).
å Fasten the BOTTOM MOLDINGS (I) to the BOTTOM (H).
Use six BLACK 1-1/8" FLAT HEAD SCREWS (22).
å NOTE: Be sure the SHORT WOODEN DOWELS insert
into the holes in the BOTTOM MOLDINGS.
Step 3
77
H
I
BLACK 1-1/8" FLAT HEAD SCREW
(6 used in this step)
22

StepStep 4
Angled head
2
å Turn twenty ANGLED HEAD CAM SCREWS (2) into the
ENDS (A and B) and TOP (C).
(20 used)
A
B
C
Page 8
Remember:
Righty tighty.
Lefty loosey.

StepStep 5
å Separate the EXTENSION SLIDES (R) from the EXTENSION RAILS (Q) as
shown in the enlarged diagram below. Be prepared, the parts are greasy.
å Fasten the EXTENSION RAILS (Q) to the ENDS (A and B). Use twelve
BLACK 1/2" PAN HEAD SCREWS (25).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in
the enlarged diagram. Then, slide the inner cartridge of the EXTENSION
RAIL in to find the other holes that lines up with the holes in the ENDS.
Turn a SCREW into those holes.
å NOTE: The EXTENSION SLIDES (R) will be used later for the DRAWERS.
Open end
Open end
Pull down on the black release lever and pull the SLIDE from the RAIL.
Q
Q
Q
Q
Q
QR
R
Use these holes.
A
B
Page 9
BLACK 1/2" PAN HEAD SCREW
(12 used in this step)
25

Step
å Gather two LOCK BRACKETS from the LOCK PACK (15).
å Fasten the LOCK BRACKETS to the BRACE (F) and TOP
MOLDING (D) as shown. Use four SILVER 1/2" FLAT
HEAD SCREWS (24).
Step 6
SILVER 1/2" FLAT HEAD SCREW
(4 used in this step)
24
Page 10
D
F
LOCK BRACKET from LOCK
PACK (15)