Teknik Hideaway Cotswold 5430446 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Hideaway Cotswold Office/Craft Station
Model 5430446
Get crafty.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
2-3
4-6
7
7-32
33-36
37-40
41-42
43
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D FIXED SHELF (1)
E BOTTOM (1)
F BACK (1)
G RIGHT DOOR (1)
H LEFT DOOR (1)
I PULL-OUT TOP (1)
J PULL-OUT BACK (1)
K FLIP-UP TOP (1)
L OUTER UPRIGHT (2)
M INNER UPRIGHT (2)
N SHELF UPRIGHT (1)
O SLIDE-OUT SHELF (1)
P SLIDING SHELF BACK (1)
Q ADJUSTABLE SHELF (6)
R LEG (1)
S FRONT MOLDING (1)
T RIGHT MOLDING (1)
U LEFT MOLDING (1)
V LEG STOP (1)
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
Part Identification
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A
B
C
D
E
F
G
H
J
K
L
I
L
M
M
N
O
P
Q
Q
Q
Q
Q
Q
R
S
T
U
V
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
18E ADJUSTABLE
GLIDE - 4
17E LEVELER
BRACKET - 4
1D OUTLET - 1
(EXTENSION SET SHOWN SEPARATED)
EXTENSION
SLIDE - 2
40MC
EXTENSION
RAIL - 2
40MA
35AW CABINET RIGHT - 1 35AY DRAWER RIGHT - 1 35AZ DRAWER LEFT - 1 35AX CABINET LEFT - 1
(EXTENSION SET SHOWN SEPARATED)
LOCKING EXTENSION
SLIDE - 2
ZY LOCKING EXTENSION
RAIL - 2
CASTER - 2
15C 16C CASTER BRACKET - 2
430446 www.sauder.com/servicePage 4
*
* This part is not suitable for the UK market

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
14M PROPEL NUT - 4
1P GROMMET
CAP - 1
16H HINGE - 2 16F MOLDING
CONNECTOR - 2
4P CORD CLIP - 1
1R METAL PIN - 24
67H HINGE - 4
5I MAGNETIC
CATCH - 2 96K PULL - 2
10P GROMMET - 1
6I STRIKE
PLATE - 2
1N NAIL - 42
2R RUBBER
SLEEVE - 24
FURNITURE TIPPING
RESTRAINT KIT - 1
97
Page 5
17P SCREW
COVER - 4
12F TWIST-LOCK®
FASTENER - 14

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
1S BLACK 9/16" LARGE HEAD SCREW - 8
9S BLACK 1-1/8" PAN HEAD SCREW - 2
7S BLACK 1-1/4" FLAT HEAD SCREW - 2
17S BLACK 7/8" LARGE HEAD SCREW - 4
27S BLACK 1-5/8" PAN HEAD SCREW - 6
2S BLACK 1-7/8" FLAT HEAD SCREW - 9
57S SILVER 2" FLAT HEAD SCREW - 5
18S BROWN 1" FLAT HEAD SCREW - 4
66S BLACK 2" PAN HEAD SCREW - 4
12S BROWN 1" FLAT HEAD SCREW - 4
23S SILVER 5/8" FLAT HEAD SCREW - 4
62S BLACK 9/16" EURO SCREW - 4
11S BLACK 1/2" FLAT HEAD SCREW - 2
3S GOLD 5/16" FLAT HEAD SCREW - 16
54S SILVER 9/16" LARGE HEAD SCREW - 16
Page 6

Hardware Usage Guide
1. Insert the dowel end of the FASTENER into the
hole of the adjoining part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoining
part while locking the FASTENER.
2. Tighten the FASTENER with a Phillips
screwdriver as tight as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the large hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push eight SAUDER TWIST-LOCK® FASTENERS (12F) into
the large holes in the FIXED SHELF (D) and BOTTOM (E).
12F
12F Do not tighten the TWIST-LOCK® FASTENERS in this step.
D
E
Page 7

Step 2
å Separate the LOCKING EXTENSION SLIDES (Z) from the LOCKING EXTENSION RAILS (Y) as shown in the upper
diagram below. Be prepared, the parts are greasy.
å Fasten the LOCKING EXTENSION RAILS (Y) to the ENDS (A and B). Use four GOLD 5/16" FLAT HEAD SCREWS (3S).
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner cartridge
of the EXTENSION RAIL in to find the other hole that lines up with the hole in the END. Turn a SCREW into this hole.
å NOTE: The EXTENSION SLIDES will be used later.
å Fasten the CABINET RIGHT (35AW) to the RIGHT END (A) and the CABINET LEFT (35AX) to the LEFT END (B). Use four
GOLD 5/16" FLAT HEAD SCREWS (3S ) through the first and second holes from the roller end in the RAIL and into the
holes of your choice in the ENDS.
å Now, insert the CORD CLIP (4P) into the hole in the RIGHT END (A). The CORD CLIP is used to hold your ELECTRICAL
OUTLET cord in place.
Push the silver tab in and pull the SLIDE from the RAIL.
Y
Z
Finished edge
Open end
Open end
4P
A
B
Y
Y
Finished edge
GOLD 5/16" FLAT HEAD SCREW
(8 used in this step)
3S
Roller end
Roller end
Page 8

å Fasten the FIXED SHELF (D) and BOTTOM (E) to the
LEFT END (B). Tighten four TWIST-LOCK® FASTENERS.
Step 3
Do not stand the unit upright without the
BACK fastened. The unit may collapse.
Caution
B
D
E
Surface with TWIST-LOCK® FASTENERS
Surface with TWIST-LOCK® FASTENERS
Page 9

Step 4
å Push two SAUDER TWIST-LOCK® FASTENERS (12F) into
the large holes in the SHELF UPRIGHT (N).
å Fasten the SHELF UPRIGHT (N) to the FIXED SHELF (D).
Use two BLACK 1-7/8" FLAT HEAD SCREWS (2S).
12F
N
D
N
BLACK 1-7/8" FLAT HEAD SCREW
(2 used in this step)
2S
Surface without
TWIST-LOCK®
FASTENERS
Page 10