Teknik 5425907 User manual

Steel Gorge Desk Milled Mesquite
Model 5425907
Sit and surf.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
3
4
5-28
29-32
33-36
37-38
39
Part Identification
Hardware Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT LEG (1)
B LEFT LEG (1)
C CENTER LEG (1)
D TOP (1)
E RIGHT END (1)
F CENTER END (1)
G CENTER UPRIGHT (1)
H LEFT UPRIGHT (1)
I BACK (1)
J LARGE BACK (1)
K SHELF (1)
L LARGE EXTENSION BLOCK (2)
M SMALL EXTENSION BLOCK (2)
N BRACE (1)
O LONG BRACE (2)
P SHORT BRACE (2)
Q LARGE DRAWER RIGHT SIDE (1)
R LARGE DRAWER LEFT SIDE (1)
S LARGE DRAWER BACK (1)
T LARGE DRAWER BOTTOM (1)
U DRAWER RIGHT SIDE (1)
V DRAWER LEFT SIDE (1)
W DRAWER BACK (1)
X DRAWER BOTTOM (1)
Y DRAWER BRACE (1)
Z DRAWER FRONT (1)
AA LARGE DRAWER FRONT (1)
Now you know
our ABCs.
Page 3
A
B
C
D
E
F
G
H
I
J
K
N
O
P
Q
R
S
T
U
V
WX
Y
Z
AA
O
M
L
P
ML

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 1-3/4" PAN HEAD SCREW - 10
13 BLACK 1" PAN HEAD SCREW - 4 14
BLACK 1" FLAT HEAD SCREW - 8
15
BLACK 1/2" FLAT HEAD SCREW - 12
19
BLACK 5/16" MACHINE SCREW - 1
21
BLACK 11/16" FLAT HEAD SCREW - 4
16
BLACK 1/2" PAN HEAD SCREW - 22
18
BLACK 1/2" MACHINE SCREW - 4
20
NUT - 1
11
WOOD DOWEL - 4
8
METAL BRACKET - 6
9TOOL - 1
12
Page 4
HIDDEN CAM - 12
5SMALL HIDDEN
CAM - 12
6CAM SCREW - 24 7
4EXTENSION SLIDE - 2 3EXTENSION RAIL - 2
(EXTENSION SET SHOWN SEPARATED)
1LEFT RAIL - 1 2RIGHT RAIL - 1
KNOB SET - 2
10 BUMPER
CARD - 1
22
BLACK 1" MACHINE SCREW - 2
23

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Fasten the LEFT LEG (B) to the LEFT UPRIGHT (H). Use
two BLACK 1-3/4" PAN HEAD SCREWS (13) and two
BLACK 1/2" PAN HEAD SCREWS (18).
Page 5
BLACK 1/2" PAN HEAD SCREW
(2 used in this step)
18
Edge with holes
Surface with holes
BLACK 1-3/4" PAN HEAD SCREW
(2 used in this step)
13
B
H
Holes facing up

Step 2
å Fasten the LEFT RAIL (1) and one of the SMALL
EXTENSION BLOCKS (M) to the LEFT UPRIGHT (H)
exactly as shown. Use two BLACK 11/16" FLAT
HEAD SCREWS (16).
å NOTE: Find the back hole first. Then, slide the inner
cartridge of the LEFT RAIL in to find the other hole that
lines up with the hole in the SMALL EXTENSION BLOCK
and LEFT UPRIGHT. Turn a SCREW into this hole.
å NOTE: You should start each SCREW a few turns before
completely tightening any of them.
Page 6
BLACK 11/16" FLAT HEAD SCREW
(2 used in this step)
16
H
M
1
These edges
should be even.
This hole is closer
to this edge.
Line up the
back hole first.
Finished surface
1
Holes facing up

å Fasten four METAL BRACKETS (9) to the CENTER
LEG (C) exactly as shown. Use four BLACK 1/2" PAN
HEAD SCREWS (18).
Step 3
Page 7
BLACK 1/2" PAN HEAD SCREW
(4 used in this step)
18
C
9

Step 4
å Fasten the CENTER LEG (C) to the CENTER END (F) and
CENTER UPRIGHT (G). Use four BLACK 1/2" PAN HEAD
SCREWS (18) through the METAL BRACKETS on the CENTER
LEG and into the CENTER END and CENTER UPRIGHT.
å Finish fastening the CENTER LEG (C) to the CENTER END (F)
and CENTER UPRIGHT (G). Use four BLACK 1-3/4" PAN
HEAD SCREWS (13).
å Turn two CAM SCREWS (7) into the CENTER END (F).
Page 8
BLACK 1/2" PAN HEAD SCREW
(4 used in this step)
18
BLACK 1-3/4" PAN HEAD SCREW
(4 used in this step)
13
G
C
F
Surface with holes
Surface with
fewer holes
Edge without holes
7

å Fasten one of the LARGE EXTENSION BLOCKS (L) to the
CENTER END (F). Use two BLACK 1" PAN HEAD SCREWS (14)
in the outer holes.
Step 5
Page 9
F
L
C
Surface with
more holes
This hole is closer
to this edge.
BLACK 1" PAN HEAD SCREW
(2 used in this step)
14

Step 6
å Carefully flip the CENTER LEG (C) over.
å Fasten the RIGHT RAIL (2) and the remaining SMALL
EXTENSION BLOCK (M) to the CENTER UPRIGHT (G) exactly
as shown. Use two BLACK 11/16" FLAT HEAD SCREWS (16).
å NOTE: Find the back hole first. Then, slide the inner cartridge
of the RIGHT RAIL in to find the other hole that lines up with
the hole in the SMALL EXTENSION BLOCK and CENTER
UPRIGHT. Turn a SCREW into this hole.
Page 10
C
BLACK 11/16" FLAT HEAD SCREW
(2 used in this step)
16
M
These edges
should be even.
This hole is closer
to this edge.
Line up the
back hole first.
Finished surface
2
G
2